A high performance, high solids, epoxy lining that is recommended for a variety of petroleum storage products including 180°F (82°C) crude oil, demineralized water 150°F (65°C), crude/water mixtures, fuel oil, jet fuel, biodiesel, and gasoline. Top Features High solids; Low VOC formula VOC compliant Excellent resistance to petroleum...
Jotun Jotamastic 80 WG
Jotun Jotamastic 80 WG (Wintergrade) is a two component polyamine cured epoxy mastic coating that is a surface tolerant, high solids product. Specially designed for application at lower temperatures to facilitate faster curing times on areas where optimum surface preparation is not possible or desired.
Jotun Jotamastic 80 WG (Wintergrade) is a two component polyamine cured epoxy mastic coating that is a surface tolerant, high solids product. Specially designed for application at lower temperatures to facilitate faster curing times on areas where optimum surface preparation is not possible or desired. Can be used as a primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces. It can be applied at sub zero surface temperatures.
Jotun Jotamastic 80 WG is primarily designed for maintenance and repair. Only aluminium containing versions to be used in immersed environments.
- Marine: Outside hulls, exterior and interior areas.
- Protective: Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller, Spray
- 7.2m² per litre
- Touch Dry
- 2.5 hours
Be the first to ask a question about this product!
Tor Non-Tainting Bitumen Solution, used to coat steelwork such as water tanks, hay sheds, etc by brush, roller or airless sprayer, drying for recoating after 8 hours. Allow tanks 7 days drying before refilling with water, allowing to stand for 24 hours before discharge and then re-fill. Ideal for farm buildings Good coverage, up to 10...
Cromadex 680 Two Pack Polyurethane Matt Primer Finish is a two pack matt primer finish; the high quality resin and curing agent help to produce excellent long term colour stability. The product contains zinc phosphate giving added corrosion resistance for greater durability. It is available in a wide range of colours, including BS, RAL, and special...
a single package, water-based, flexible mastic fire protective coating for cables and cable trays. Can be applied to electrical cables to retard fire propagation. Top Features Flexible Allows easy replacement of cables Asbestos-Free – complies with EPA and OSHA regulations Factory Mutual – tested and approved Does not de-rate cables
A higher solids, better coverage and lower VOC content product than the standard 9100 Epoxy. Two-pack, glossy epoxy coating for metal, walls and floors. The most efficient epoxy system providing a very hard coating with high layer thickness for lasting results even with a single coat application.
A high solids epoxy lining with exceptional chemical resistance. Primarily as a tank lining, it is recommended for storage of crude oil (180°F/82°C), demineralized water (150°F/65°C), tap water (200°F/93°C) food and beverage industries, and water and wastewater exposures. Top Features High solids; Low VOC formula VOC compliant Excellent...
Sherwin-Williams Dura-Plate 301K is a solvent-free, surface and humidity tolerant two-pack modified epoxy that can be applied without dew point restrictions and over wet steel surfaces. It is an anticorrosive coating for long service life steel protection that can be used for both immersion and above the waterline service in marine, offshore, construction...
Jotun Jotamastic 87 Alu provides long lasting protection in environments with high corrosivity. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces. It can be applied at sub zero surface temperatures.
Jotun Inhibitor 53 is a specially developed additive for Jotun Baltoflake Ecolife, Jotun Chemflake Special and Jotun Chemflake CV products - refer to each product data sheet for further information.
Jotun Penguard Universal is a two component polyamine cured pure epoxy coating that is a fast drying, all year round, high solids, high build product. Jotun Penguard Universal provides excellent corrosion protection as part of a complete coating system and can be used as primer, mid coat, finish coat or as a single coat system in atmospheric and immersed...
International Interseal 670HS (Winter Grade) is supplied with a winter grade curing agent to enable more rapid cure at lower temperatures. The product is still a low VOC, two component high build, high solids surface tolerant epoxy maintenance coating, for application to a wide variety of substrates including hand prepared rusty steel and a wide range of...
Jotun Baltoflake is a glass flake reinforced unsaturated polyester coating. This Jotun product is an ultra high build, extremely abrasion resistant and fast curing barrier coating that can be used as primer, mid coat or finish coat in atmospheric and immersed environments.
Jotun Jotamastic 90 GF is a two component polyamine cured epoxy mastic coating that is a surface tolerant, abrasion resistant, high solids and high build. It is reinforced with glass flakes for improved abrasion and scratch resistance. Specially designed for areas where optimum surface preparation is not possible or desired.
International Intergard 410 is a high build, high performance, two component epoxy with excellent chemical and abrasion resistance suitable for use as part of a high performance coating system to provide an anti-corrosive barrier in areas where aggressive corrosion conditions prevail.
Sherwin-Williams Macropoxy M922 (formerly Epigrip M922) is a high solids, 2-pack glass flake epoxy pigmented with micronised glass flake and anti-corrosives to provide anti-corrosive protection of blast cleaned steel and cathodically protected steel. Macropoxy M922 possess excellent abrasion resistance and has excellent resistance to immersion in sea...