Jotun Jotamastic 87 Alu provides long lasting protection in environments with high corrosivity. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces. It can be applied at sub zero surface temperatures.
Jotun Jotamastic 87 Alu paint from the popular direct to metal paint brand, Jotun, is a two component polyamine cured epoxy mastic coating for steel. It is a surface tolerant, high solids, high build product that is aluminium pigmented for improved barrier effect. Specially designed for areas where optimum surface preparation is not possible or desired.
Jotun Jotamastic 87 Alu provides long lasting protection in environments with high corosivity. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces. It can be applied at sub zero surface temperatures.
General: Primarily designed for maintenance and repair.
Marine: Outside hulls, exterior and interior areas, including water balast tanks.
Protective: Recommended for offshore environments, including splash zones, refineries, power plants, bridges, buildings, mining equipment and general structural steel.
Approvals and certificates
Low flame spread class 1, BS 476, Part 7, 1971. Warrinton Fire reasearch, Naval Eng, Stand 713: Isue 3
Grain, Newcastle Ocupational Health
Part of a complete system that is certified to Network Rail Line Specification NR/L3/CIV/039 System M24 (Cert. No's. XM92/M24-141, XM92/M24-142)
Additional certificates and approvals may be available on request
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Is this product Jotunmastic 87 heat resistant, if yes to what degree?
Answer from Rawlins’ Technical Team:
The temperature resistant properties of Jotun Jotamastic 87 Alu are as follows;
Immersed, sea water
Peak temperature duration max. 1 hour.
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures.
Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in the system have similar heat resistance.
Mike Hazeltine on 2017-10-18 14:11:33
Question: Its not so much a question on your product, but a question on preparation.
I have a steel keel on my yacht (type unknown), but its become very rusty (type D) and I am looking at using your paint. If I was to use power tools, would I need to remove all the rust marks and secondly where the steel is pitted should I use your paint first and then fill (Please advise type of filler) or should I perhaps use a 2 pack epoxy primer as a filler.
Answer from Rawlins’ Technical Team:
The way forward is to get the best possible surface preparation, removing most of the corrosion. More importantly we need a roughness so avoid polishing the steel if sanding/discing.
Vital is to then to detergent wash (fairy liquid soapy solution) and rinse thoroughly with fresh water, high pressure if possible to remove contamination.
We would then suggest (if application by brush) Jotamastic Smart Pack, minimum 3 coats, 4 is better. Apply 1 st coat direct to steel, allow to dry and then fill with an epoxy filler, allow to dry, sand and then continue with further coats.
Jotun Jotamastic 87 Alu is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
SET 1 (Hand Tools)
1 x Rust-Oleum...