Carboline Carbothane 134 HP(replaces Nullifire TS134 Acrylic Polyurethane Top Seal) is a two-component, high-gloss, and high-solid polyurethane topcoat, which can be easily sprayed with conventional as well as airless equipment. The coating has excellent flow and application properties which provides a smooth, durable, and easy to clean surface.
Please note: Colours are Made To Order subject to a MOQ of 80 units and an extended lead time of 10 working days
Excellent weatherability
Excellent flexibility
Excellent abrasion resistance
Available in 350+ RAL and BS colours
Easy application with airless and conventional equipment
Suitable for plural component and electrostatic spray
VOC compliant to current AIM regulations
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Professional use only - from the 24th August 2023, adequate training is required before industrial or professional use of this product.
Carboline Carbothane 134 HP, also known as Nullifire TS134 Acrylic Polyurethane Top Seal is a two-component, high-gloss and high-solid polyurethane topcoat, which can be easily sprayed with conventional as well as airless equipment. The coating has excellent flow and application properties which provides a smooth, durable, and easy to clean surface.
Easy application with airless and conventional equipment
Suitable for plural component and electrostatic spray
VOC compliant to current AIM regulations
Product Specification
Technical Data
Carboline Carbothane 134 HP
Volume Solids:
65% ± 2%
Theoretical Coverage Rate:
8,6 m² at 75 microns
Allow for loss in mixing and application
Dry Film Thickness:
75 microns per coat
Do not exceed 150 microns in a single coat
Dry Temperature Resistance:
Continuous: 93°C
Non-Continuous: 121°C
Discolouration and loss of gloss may occur above 93ºC
VOC Values:
As supplied: 300 g/l
These are nominal values and may vary slightly with colour
Shelf Life:
24 months at 24°C
Storage Temperature and Humidity:
4°C - 43°C
0-80% Relative Humidity
Drying Times
Curing Schedule
Surface Temp. and 50% Relative Humidty
Dry to Handle
Final Cure
4°C
18 hours
14 days
10°C
8 hours
7 days
24°C
4 hours
3 days
32°C
1 hour
1 day
These times are based on 50-75 microns dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure
Surface Preparation
General
Surfaces must be clean and dry
Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating
Steel
Prime with specific Carboline primers as recommended by Rawlins on Tech - 0113 2455450 (option 2) or [email protected]
Galvanised Steel
Sa1 and prime with specific Carboline primers as recommended by Rawlins
Aluminium
Sa1 and prime with appropriate Carboline primer as recommended by Rawlins
Previously Painted Surfaces
Lightly sand or abrade to roughen and de-gloss the surface. Existing paint must attain a minimum 3B rating in accordance with ASTM D3359 “X-Scribe” adhesion test
Prime with specific Carboline primers as recommended by Rawlins
Application Methods
Product Information
Mixing:
Power mix Part A separately, then combine with Part B and power mix
Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied
Ratio:
4:1 (A to B)
Pot Life:
4 Hours at 24ºC and less at higher temperatures
Pot Life ends when coating becomes too viscous to use. Moisture contamination will shorten Potlife and cause gellation
Conventional Spray
Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, .070” I.D. fluid tip and appropriate air cap
Airless Spray:
Pump Ratio: 30:1 min
Volume Output: 3.0 gpm min
Material Hose: 3/8” I.D. min
Tip Size: .015-.017”
Pressure: 148-162 BAR
Filter Size: 60 mesh
Brush and Roller:
Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding. Avoid re-brushing or re-rolling. For best results, tie-in within 10 minutes at 24°C
Brush:
Recommended for touch-up only. Use a medium, natural bristle brush
Roller:
Use a short-nap mohair roller cover with phenolic core
Application Conditions
Product Conditions
Condition
Material
Surface
Ambient
Humidity
Normal
16 -29°C
16 -29°C
16 -29°C
40-60%
Minimum
10°C
4°C
4°C
10%
Maximum
38°C
49°C
35°C
80%
Industry standards are for substrate temperatures to be 3ºC above the dew point
This product is moisture sensitive in the liquid stage and until fully cured. Protect from high humidity, dew, and direct moisture contact until fully cured
Application and/or curing in humidity above maximum, or exposure to moisture from rain or dew may result in a loss of gloss and/or micro bubbling of the product
Health and Safety
Clean Up
Use Thinner 2 or Acetone
In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
Read and follow all caution statements on this product data sheet and on the safety data sheet for this product and use personal protective equipment as directed
Hypersensitive persons should wear protective clothing, gloves, and use protective cream on face, hands, and all exposed areas
Ventilation
When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
User should test and monitor exposure levels to ensure all personnel are below guidelines
If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator
Refer to the product and safety data sheet in the attachments section above for further details
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Nullifire TS134 - Acrylic Polyurethane Top Seal is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...