Plasite 4550 S is a 100% solids, flake filled, premium novolac epoxy coating designed for internal steel and concrete substrates. It is a two-component system consisting of four-parts by volume of Part A resin and one part by volume of Part B hardener. Tested and is approved for crude oil storage and transportation up to 350°F (177°C). This...
Jotun Marathon 1000 GF
Jotun Marathon 1000 GF is a two component polyamine cured epoxy coating. It is a high build, solvent free, glass flake reinforced product. It has very good impact and abrasion resistance. Suitable for environments with very high corrosivity, such as areas in the splash or tidal zone. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments.
Jotun Marathon 1000 GF is a two component polyamine cured epoxy coating. It is a high build, solvent free, glass flake reinforced product. It has very good impact and abrasion resistance. Suitable for environments with very high corrosivity, such as areas in the splash or tidal zone. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel substrates.
- Suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed.
- Recommended for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel.
- Specially suited in areas where high mechanical strength is required, such as splash or tidal zones.
- Can be used as a non-slip deck system in combination with appropriate Anti-Skid aggregate and finish coat.
- Compatible with cathodic protection systems.
Approvals and certificates
- Pre-qualification testing in accordance with NORSOK M-501, Rev. 6, System 1, suitable for exterior exposure in offshore environment, below 120 °C.
- Pre-qualification testing in accordance with NORSOK M-501, Rev. 6, System 4, suitable for decks and walkways.
- Pre-qualification testing in accordance with NORSOK M-501, Rev. 6, System 7, suitable for splash zones.
Additional certificates and approvals may be available on request.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 1 - 2m² per litre
- Touch Dry
- 7 Hours
- Brush, Spray
Be the first to ask a question about this product!
Jotun Jotamastic Smart Pack is a two component amine cured epoxy mastic coating that is a surface tolerant, high solids, high build product. Specially designed for application with brush and roller with a 1:1 mixing ratio for easy use and reduced wastage. Specially designed for areas where optimum surface preparation is not possible or desired.
A two component, 95% solids epoxy based intumescent coating for the fire protection of structural steel. Designed to fireproof steelwork for up to a 4 hour fire rating. Top Features UL listed - for both interior and exterior environments Durable finish Thin film coating VOC compliant Easy repair
Jotun Jotamastic Plus is a two component amine cured epoxy mastic coating that is surface tolerant, high solids and high build. It is specially designed for areas where optimum surface preparation is not possible or desired. Provides long lasting protection in environments with high corrosivity and can be used as a primer, mid coat, finish coat or as a...
Aquazinga, a two-pack anti-corrosion system providing cathodic protection to ferrous metals, and can be used as an alternative to hot-dip galvanisation or metallisation. Designed to withstand high temperatures (up to 600°C) and corrosive environments and severe conditions such as ballast tanks, turbine exhausts and high-heat pipelines....
Sherwin-Williams Dura-Plate 301S is an anticorrosive coating for long service life steel protection, normally used as an intermediate or topcoat as part of a 301 based coating system when very high edge retentive is required. It can be used for both immersion and above the waterline service in marine, offshore, construction and industrial applications.
A glass reinforced chemically resistant epoxy coating with wide versatility in all industrial markets, including marine applications. Top Features Low-temperature version: 890 LT GF Self-priming and primer/finish capabilities Excellent abrasion resistance & hardness
Jotun Norpol Accelerator 9826 (formerly known as Jotun Accelerator DMA10) is a specially developed additive for Jotun Chemflake Special and Jotun Chemflake CV products - refer to each product data sheet for further information.
Jotun Jotamastic SF WG is a 'Wintergrade' version of Jotun Jotamastic SF to aid application in lower temperatures and to provide faster drying and curing times. Jotun Jotamastic SF WG is a two component polyamine cured epoxy mastic coating that is a surface tolerant, solvent free, high build product. Well suited for early immersion.
A quick drying, White Spirit based alkyd topcoat with good light and weather resistance that is suitable for interior and exterior use. Top Features May be diluted up to 20% 24 month shelf life High gloss finish
International Interbond 1202UPC (Universal Pipe Coating) is the universal pipe coating that reduces specification complexity and project costs. Suitable for protecting above-ground piping and accessories in new construction process plant operating at temperatures between -196ºC (-321ºF) to +650ºC (1202ºF).
A high performance immersion-grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures. It is typically used on hot steel substrates under insulation operating continuously up to 400°F/204°C. Top Features Continuous temperature resistance to 204°C Very good flexibility Acceptable for use...
Sikalastic 844 XT is a two part, elastic, very fast curing modified polyurea spray applied membrane where exposure to high acidic and alkaline chemical concentrations are present, therefore also suitable for the use in closed structures containing biogenic sulphuric acid. Sikalastic 844 XT can only be spray applied with special two part hot spray equipment.
Nu-Flame HB Metal Primer is ideal for priming cast iron and structural steel in preparation to apply the Nu-Flame Fire Retardant System for metals. Advantages Quick dry. Ideal for cast iron and structural steel. 8m²/Litre coverage. 3 colours available. 12-month shelf life.
An extremely abrasion and chemical resistant polyester coating with multiple layers of glass flakes incorporated in a highly cross-linked polyester matrix. Top Features Ideal for long-term protection in marine environments. Used as a tank lining and for areas exposed to many acids. Recommended for protection of steel.