Carboline Carboguard 890 LT is a highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. This product is self-priming and suitable for application over most existing coatings, and tightly adherent to rust.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].
Carboline Carboguard 890 LT is a highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Self-priming and suitable for application over most existing coatings, and tightly adherent to rust. Excellent for use as a primer or intermediate coat where low temperature cure is needed. Can be used in a variety of chemical environments. May be used as a self-priming or finish coat on exterior exposure if discolouration can be tolerated.
| Technical Data | ||||||
|---|---|---|---|---|---|---|
| Carboline Carboguard 890 LT | ||||||
| Volume Solids: | 80% +/- 2% | |||||
| Theoretical Coverage Rate: | 1283 ft²/gal at 1.0 mils (31.5 m²/l at 25 microns) | |||||
| 321 ft²/gal at 4.0 mils (7.9 m²/l at 100 microns) | ||||||
| 214 ft²/gal at 6.0 mils (5.2 m²/l at 150 microns) | ||||||
| Allow for loss in mixing and application | ||||||
| Dry Film Thickness: | Use 6-8 mils (152-203 microns) over tight rust or severe environments. Do not exceed 10 mils (250 microns) in a single coat. Excessive film thickness over inorganic zincs may increase damage during shipping or erection. | |||||
| Primer: | Self-priming. May be applied over inorganic zinc primers and other tightly adhering coatings. A mist coat may be required to minimize bubbling over inorganic zinc primers. | |||||
| Topcoat: | May be coated with acrylics, epoxies, or polyurethanes depending on exposure and need. | |||||
| VOC Values: | As supplied: 1.5 lbs/gal (180 g/l) | |||||
| Thinner 2: 15 oz/gal = 2.0lbs/gal (250 g/l) | ||||||
| Thinner 33: 14 oz/ga l= 2.0 lbs/gal (250 g/l) | ||||||
| These are nominal values and may vary slightly with colour | ||||||
| Flash Point: | 89°F (32°C) for Part A | |||||
| 73°F (23°C) for Part B | ||||||
| 85°F (29°C) for mixed | ||||||
| Limitations: | Do not apply over acrylic or alkyd coatings. If discolouration is objectionable it may be top coated. Use only factory-made colours for splash zone or immersion service. | |||||
| Shelf Life: | Part A: Min. 36 months at 75°F (24°C) | |||||
| Part B: Min. 15 months at 75°F (24°C) | ||||||
| Storage Temperature and Humidity: | 40° - 110°F (4° - 43°C) | |||||
| 0-100% Relative Humidity | ||||||
| Curing Schedule | ||||
|---|---|---|---|---|
| Surface Temp | Dry to Handle | Dry to Recoat and Topcoat with Other Finishes | Dry to Touch | Final Cure General |
| 35°F (2°C) | 18 Hours | 20 Hours | 5 Hours | 7 Days |
| 40°F (4°C) | 15.5 Hours | 16 Hours | 4.5 Hours | 5 Days |
| 50°F (10°C) | 6.5 Hours | 12 Hours | 3.5 Hours | 3 Days |
| 60°F (16°C) | 5 Hours | 8 Hours | 2 Hours | 2 Days |
| 75°F (24°C) | 2 Hours | 4 Hours | 1.5 Hours | 24 Hours |
| 90°F (32°C) | 1.5 Hours | 2 Hours | 1 Hour | 16 Hours |
Steel
Galvanised Steel
Concrete or CMU
Dry Wall and Plaster
Previously Painted Surfaces
| Product Information | |||||
|---|---|---|---|---|---|
| Mixing: | Power mix separately, then combine and power mix. DO NOT MIX PARTIAL KITS. | ||||
| Thinning: | Spray: Up to 13 oz/gal with Thinner 2 | ||||
| Brush or Roller: Up to 14 oz/gal with Thinner 33 | |||||
| Thinner 33 can be used for spray in hot/windy conditions. Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied. | |||||
| Ratio: | 1:1 Ratio (A to B) | ||||
| Pot Life: | 2 Hours at 75°F (24°C) Pot life ends when coating loses body and begins to sag. Pot life times will be less at higher temperatures. | ||||
| Spray Application (General) | This is a high solids coating and may require adjustments in spray techniques. Wet film thickness is easily and quickly achieved. | ||||
| Conventional Spray: | Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, 0.070” I.D. fluid tip and appropriate air cap. | ||||
| Airless Spray: | Pump Ratio: 30:1 (min) | ||||
| GPM Output: 3.0 (min) | |||||
| Material Hose: 3/8” I.D. (min) | |||||
| Tip Size: 0.017”-0.021” | |||||
| Output PSI: 2100-2300 | |||||
| Filter Size: 60 mesh | |||||
| Brush and Roller (General): | Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding. Avoid excessive re-brushing or rerolling. For best results, tie-in within 10 minutes at 75°F (24°C). | ||||
| Brush: | Use a medium bristle brush | ||||
| Roller: | Use a short-nap synthetic roller cover with phenolic core | ||||
| Product Conditions | |||||
|---|---|---|---|---|---|
| Condition | Material | Surface | Ambient | Humidity | |
| Minimum | 40°F (4°C) | 35°F (2°C) | 35°F (2°C) | 0% | |
| Maximum | 90°F (32°C) | 125°F (52°C) | 110°F (43°C) | 90% | |
Clean Up
Safety
Ventilation
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Carboline Thinner 2 is a thinner for use in industrial coatings. More Information
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
