Carboline Carbothane 133 HB

8659

Carboline Carbothane 133 HB is a two-component high build, low sheen finish that has excellent resistance to corrosion, chemicals, and abrasion. Suitable for application over several Carboline primers and intermediates, this material provides very good weathering performance.

  • Available in 350+ RAL and BS colours
  • Outstanding performance properties in both mild and aggressive environments
  • High build; suitable for many two-coat systems
  • Suitable for application direct to inorganic zincs
  • Indefinite re-coatability

Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.

Product customisation

Don't forget to save your customization to be able to add to cart
  • 250 char. max
Colour Group
Size
Finish
£73.80
£88.56 Incl. VAT
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

100% secure payments
Description

Carboline Carbothane 133 HB is a two-component, high build, low sheen finish that has excellent resistance to corrosion, chemicals, and abrasion. Suitable for application over several Carboline primers and intermediates, this material provides very good weathering performance in 400+ RAL colours



Click To Jump To Section:




Features and Benefits


  • Outstanding performance properties in both mild and aggressive environments
  • High build; suitable for many two-coat systems
  • Suitable for application direct to inorganic zincs
  • Application by spray, brush, or roller
  • Indefinite re-coatability
  • VOC compliant to current AIM regulations
  • Available in 400+ RAL colours



Product Specification


Technical Data
Carboline Carbothane 133 HB
Volume Solids: 57% +/- 2%
Theoretical Coverage Rate: 22.4 m²/l at 25 microns
7.5 m²/l at 75 microns
4.5 m²/l at 125 microns
Allow for loss in mixing and application
Dry Film Thickness: 76 - 127 microns per coat
Dry film thickness in excess of 175 microns per coat is not recommended
Dry Temperature Resistance: Continuous: 93°C
Non-Continuous: 121°C
Discolouration and loss of gloss is observed above 93°C
VOC Values: As Supplied : 383 g/l
Thinner 214: 403 g/l
Thinner 241: 423 g/l
Thinner 25: 420 g/l
Thinner 25: 18 oz/gal: 449 g/l
1.5 oz/gal of Additive 101 adds 10 g/l. These are nominal values and may vary slightly with colour
Topcoat: Topcoat with Carbothane Clear Coat when required
Limitations: The alignment of aluminium flakes in aluminium-filled finishes is very dependent on application conditions and techniques. Care must be taken to keep conditions as constant as possible to reduce variations in final appearance. It is also advisable to work from a single batch of material since variations can occur from batch to batch
Flash Point: Part A: 35°C
Part B: 33°C
Shelf Life: Part A: Min. 36 months at 24°C
Part B: Min. 24 months at 24°C
Storage Temperature and Humidity: 4°C - 43°C
0-90% Relative Humidity



Performance Data
Test Method System Surface
ASTM B117 Salt Fog Blasted Steel 1 ct. IOZ 1 ct. 133 HB No rusting, or blistering on plane or scribe 2,000 hours
ASTM B117 Salt Fog Blasted Steel 1 ct. OZ 1 ct. 133 HB No rusting, or blistering on plane or scribe 4,000 hours
ASTM D1735 Water Fog Blasted Steel 1 ct. Epoxy 1 ct. 133 HB No rusting or blistering after 8600 hours
ASTM D4213 Scrub Resistance 1 ct. 133 HB .0027 microliters erosion rate after 100 cycles with abrasive scrub medium.
ASTM D4585 Humidity Blasted Steel 1 ct. IOZ 1 ct. 133 HB No rusting or blistering after 3000 hours
ASTM D5894 QUV A Prohesion 1 ct. 133 HB No effect on plane area and 78% gloss retention after 1008 hours of wet/dry salt fog cycle
ASTM G26 Weatherometer Blasted Steel 1 ct IOZ 1 ct. 133 HB No blistering, rusting or cracking after 3500 hours
ASTM G53 QUV (2500 hours w/ UVA 340 bulb) Blasted Steel 1 ct. Epoxy 1 ct. 133 HB Colour change less than 2 McAdam units; no blistering, rusting, cracking, or chalking
Graffiti Resistance Blasted Steel 1 ct. Epoxy 1 ct. 133 HB All markings and stains removed by solvent after exposure to: shoe polish, sharpie marker, crayon, l



Drying Times


Curing Schedule
Surface Temp. Dry to Handle Dry to Recoat Final Cure General
4°C 20 Hours 20 Hours 28 Days
10°C 12 Hours 12 Hours 14 Days
24°C 5 Hours 5 Hours 7 Days
32°C 1 Hour 1 Hour 4 Days



  • These times are based on a 75-125 micron dry film thickness. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure
  • Maximum recoat times are indefinite
  • Surface must be clean and dry
  • As part of good painting practice it is recommended to test for adhesion by wiping the surface with Thinner 25
  • If the film shows a slight "tack" the surface is suitable for recoating without extensive surface preparation such as abrading
  • Carboline Additive 101 can be used to accelerate the film forming process in this product for conditions outside of the parameters of this data sheet. Carboline Additive 101 is added at a rate of 1.0-2.0 oz per mixed gallon or a maximum of 6 oz per mixed five gallons. At this addition rate, Additive 101 will accelerate the cure rate of the urethane product between 25-40% depending on the substrate temperature range and reduce the pot life of the product by approximately 40-50% of that stated on the product data sheet. With the use of Additive 101, this product will continue to cure at temperatures as low as -7°C



Surface Preparation


General

  • Surfaces must be clean and dry
  • Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating

Steel

  • SSPC-SP6 with a 37.5-62.5 micron surface profile for maximum protection
  • SSPCSP2 or SP3 as minimum requirement
  • Prime with specific Carboline primers as recommended by Rawlins on Tech - 0113 2455450 (option 2) or [email protected]

Galvanised Steel

  • Prime with specific Carboline primers as recommended by Rawlins
  • Refer to the specific primer’s product data sheet for substrate preparation requirements

Aluminium

  • SSPC-SP1 and prime with appropriate Carboline primer as recommended by Rawlins

Previously Painted Surfaces

  • Lightly sand or abrade to roughen and de-gloss the surface. Existing paint must attain a minimum 3A rating in accordance with ASTM D3359 “XScribe” adhesion test
  • Prime with specific Carboline primers as recommended by Rawlins



Application Methods


Product Information
Mixing: Power mix Part A separately, then combine with Part B and power mix
Do not mix partial kits
Thinning: Spray: Up to 11 oz/gal (9%) w/ Thinner 25
Roller: Up to 18 oz/gal (14%) w/ Thinner 25
Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied. Thinner 214 may also be used, up to 6 oz/gal, for either spray or brush/roller application. Carboline Thinner 236 E may also be used to minimize HAP and VOC emissions
Ratio: 6:1 Ratio (A to B)

.88 Gal. Kit Part A:

1 gal. can (partial filled) UC 133: 1 pint

5.0 Gal. Kit

Part A: 5 gal. can (partial filled) UC 133: 1 gallon can (partial filled)

Pot Life: 4 Hours at 24°C and less at higher temperatures
Pot life ends when coating becomes too viscous to use
Spray Application (General) This is a high solids coating and may require adjustments in spray techniques. Wet film thickness is easily and quickly achieved.
Conventional Spray Pressure pot equipped with dual regulators
3/8” I.D. minimum material hose
070” I.D. fluid tip and appropriate air cap
Airless Spray: Pump Ratio: 30:1 min
Volume Output: 3.0 gpm min.
Material Hose: 3/8” I.D. min
Tip Size: .013-.015”
Output PSI: 2000-2300 psi
Filter Size: 60 mesh
Brush and Roller:

Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding. Avoid excessive re-brushing or rerolling

For best results, tie-in within 10 minutes at 24°C

Brush:

Recommended for touch-up only

Use a medium, natural bristle brush

Roller: Use a medium-nap synthetic roller cover with phenolic core



Application Conditions


Product Conditions
Condition Material Surface Ambient Humidity
Minimum 4°C 4°C 4°C 0%
Maximum 38°C 43°C 43°C 90%



  • Industry standards are for substrate temperatures to be 3°C above the dew point
  • This product simply requires the substrate temperature to be above the dew point
  • Caution: This Product is moisture sensitive in the liquid stage and until cured. Protect from high humidity, dew, and direct moisture contact until cured. Application and/or curing in humidity's above maximum, or exposure to moisture from rain or dew may result in a loss of gloss and/or micro-bubbling of the product.



Health and Safety


Clean Up

  • Use Thinner 2 or Acetone
  • In case of spillage, absorb and dispose of in accordance with local applicable regulations

Safety

  • Read and follow all caution statements on this product data sheet and on the SDS for this product and use personal protective equipment as directed

Ventilation

  • When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
  • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
  • In addition to ensuring proper ventilation, appropriate respirators must be used by all application personnel
  • User should test and monitor exposure levels to ensure all personnel are below guidelines. If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator

Caution

  • This product contains flammable solvents
  • Keep away from sparks and open flames
  • Refer to the product data sheet and safety data sheets in the attachments section above for further details
Product Details
8659

Data sheet

Manufacturer
Carboline
Water / Solvent Based
Solvent
For Use On
Steel, Galvanized Steel, Aluminium
Application Method
Conventional Spray, Airless Spray, Brush, Roller
Sheen
Satin
Colour
Fully Tintable
Single, Two or Three Pack
Two-pack
Pack Size
5L
UN Number
UN1263, UN1866
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22
In Stock and Available for Delivery