Carboline Phenoline 353

0657A1NL

Carboline Phenoline 353 is a two-component, highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. It has a unique blend of resins that make it highly resistant to a variety of aggressive cargos like gasoline, gasoline blends, biodiesel, fuel oils, and others.

  • Outstanding overall chemical resistance
  • Dense, highly cross-linked film for superior barrier protection
  • Excellent abrasion resistance and toughness
  • Well-suited for hydrocarbon exposures
  • Low temperature cure version available

This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].

Colour
Size
Finish
Quantity
Product not available
This Product is Price on Application Only

100% secure payments
Description

Carboline Phenoline 353 is a two-component, highly cross-linked epoxy lining with extraordinary overall chemical resistance and versatility. It has a unique blend of resins that make it highly resistant to a variety of aggressive cargos like gasoline, gasoline blends, biodiesel, fuel oils, and others. It can be used is both acidic and high temperature caustic exposures. Markets served are terminals, refineries, petrochemical, wastewater, railcar linings, and many others.



Click To Jump To Section:




Features and Benefits


  • Outstanding overall chemical resistance
  • Dense, highly cross-linked film for superior barrier protection
  • Excellent abrasion resistance and toughness
  • Well-suited for hydrocarbon exposures
  • Low temperature cure version available



Product Specification


Technical Data
Carboline Phenoline 353
Volume Solids: 75% +/- 2%
Theoretical Coverage Rate:

29.5 m²/l at 25 microns

5.9 m²/l at 125 microns

4.9 m²/l at 150 microns

Allow for loss in mixing and application
Dry Film Thickness: 127 - 152 microns per coat
Two coats are generally recommended to 250-300 microns total DFT
VOC Values: As Supplied: 206 g/l

Thinner 2: 8 oz/gal w/ #:2 2.04 lbs/gal (244 g/l)

These are nominal values and may vary slightly with colour.

Dry Temp. Resistance: Continuous: 121°C
Non-Continuous: 149°C
Limitations: Linings exposed to cargos warmer than the outside steel temperature are subject to a “cold-wall” effect. The smaller the temperature differential the less negative effect on performance. Epoxies lose gloss, discolour and eventually chalk in sunlight exposure
Flash Point:

Part A: 27°C

Part B: 13°C

Mixed: 30°C

Shelf Life: Part A and B: Min. 24 months at 24°C
Storage Temperature and Humidity: 4°-43°C
0-90% Relative Humidity



Drying Times


Curing Schedule
Surface Temp Minimum Recoat Time Maximum Recoat Time Final Cure Immersion
16°C 12 Hours 10 Days 10 Days
24°C 8 Hours 7 Days 7 Days
32°C 6 Hours 2 Days 5 Days



  • These times are based on a 125-175 micron dry film thickness and adequate ventilation for the release of solvents for proper cure. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment, delamination between coats and premature failure
  • Excessive humidity or condensation on the surface during curing can interfere with the cure, can cause discolouration and may result in a surface haze. Any haze or blush must be removed by water washing before recoating
  • Recoat intervals may vary from those listed above when using under intumescent fireproofing products
  • Contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] for recommended cure times before applying Carboline intumescent products.
  • If the maximum recoat time is exceeded, the surface must be abraded prior to the application of additional coats
  • Note: It is recommended to cure above 16°C for aggressive service



Curing Schedule
Surface Temp Final Cure Immersion
66°C 8 Hours



  • The above curing schedule may be used to force cure the coating system
  • Allow the freshly applied coating to air dry for 4 hours prior to elevating temperature
  • Elevate temperature no more than 15°C every 30 minutes

Surface Preparation


General

  • Surfaces must be clean and dry
  • Employ adequate methods to remove dirt, dust, oil, and all other contaminants that could interfere with adhesion of the coating

Steel

  • Immersion: SSPC-SP10 minimum
  • Profile: 38-75 microns
  • When using under fireproofing products, defer to the primer surface preparation requirements in the product data sheet of the fireproofing product

Concrete or CMU

  • Immersion: Concrete must be cured 28 days at 24°C and 50% relative humidity or equivalent.
  • Prepare surfaces in accordance with ASTM D4258-92 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete
  • Voids in concrete may require surfacing



Application Methods


Product Information
Mixing:

Power mix separately, then combine and power mix

When using between 15-21°C, mix and allow the material to "sweat-in" for 15 minutes before using

Do not mix partial kits
Thinning: May be thinned up to 8 oz/gal with Thinner 2
Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied
Ratio: 4:1 Ratio (A to B)
Pot Life:

2 Hours at 24°C

Pot life ends when coating shows dramatic changes in viscosity

Pot life times will be less at higher temperatures

Conventional Spray: Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, 0.055-0.070” I.D. fluid tip and appropriate air cap
Airless Spray:

Pump Ratio: 30:1 (min.)

GPM Output: 3.0 (min.)

Material Hose: 3/8” I.D. (min.)

Tip Size: 0.015-0.019”

Output PSI: 2100-2300

Filter Size: 60 mesh

Brush and Roller (General): Not recommended for tank lining applications except when striping welds and touching up
Brush: Use a medium bristle brush
Roller: Use a short-nap synthetic roller cover with phenolic core



Application Conditions


Product Conditions
Condition Material Surface Ambient Humidity
Minimum 16°C 10°C 10°C 0%
Maximum 32°C 43°C 38°C 85%



  • This product simply requires the substrate temperature to be above the dew point
  • Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate
  • Special application techniques may be required above or below normal application conditions



Health and Safety


Clean Up

  • Use Thinner 2 or Acetone
  • In case of spillage, absorb and dispose of in accordance with local applicable regulations

Safety

  • Read and follow all caution statements on this product data sheet and on the safety data sheets for this product and use personal protective equipment as directed
  • Employ normal workmanlike safety precautions

Ventilation

  • When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
  • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
  • In addition to ensuring proper ventilation, appropriate respirators must be used by all application personnel

Caution

  • This product contains flammable solvents. Keep away from sparks and open flames
  • All electrical equipment and installations should be made and rounded in accordance with applicable local regulations
  • In areas where explosion hazards exist workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
  • Refer to the product data sheet and safety data sheets in the attachments section above for further details
Product Details
0657A1NL

Data sheet

Manufacturer
Carboline
For Use On
Steel, Concrete
Application Method
Brush, Roller, Spray
Sheen
Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
10L
Mixing Ratio
4:1 Ratio (A to B)
Coverage
1203 ft²/gal at 1.0 mils (29.5 m²/l at 25 microns) - 241 ft²/gal at 5.0 mils (5.9 m²/l at 125 microns) - 200 ft²/gal at 6.0 mils (4.9 m²/l at 150 microns)
Recommended Thinner/Cleaner
Carboline Thinner 2
Max. Application Temperature
Material: 32°C - Surface: 43°C - Ambient: 38°C - Humidity: 85%
Min. Application Temperature
Material: 16°C - Surface: 10°C - Ambient: 10°C - Humidity: 0%
Solids by Volume
75% +/- 2%
VOC
As Supplied: 1.72 lbs/gal (206 g/l)
Shelf Life (from date of manufacture)
Part A and B: Min. 24 months at 24°C
Recommended Dry Film Thickness
5 - 6 mils (127 - 152 microns) per coat
UN Number (Activator)
UN3469
UN Number (Base)
UN1263
Dry to Recoat
16°C: Min 12 Hours - Max 10 Days, 24°C: Min 8 Hours - Max 7 Days, 32°C: Min 6 Hours - Max 2 Days
Fully Cured
16°C: 10 Days - 24°C: 7 Days - 32°C: 5 Days
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22
In Stock and Available for Delivery