Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Carboline Phenoline 187 VOC is a two-component, high solids epoxy lining with exceptional chemical resistance. Primarily as a tank lining, it is recommended for storage of crude oil (82°C), demineralized water (65°C), tap water (93°C) food and beverage industries, and water and wastewater exposures.
Carboline Phenoline 187 VOC is a two-component, high solids epoxy lining with exceptional chemical resistance. Primarily as a tank lining, it is recommended for storage of crude oil 82°C, demineralized water 65°C, tap water 93°C food and beverage industries, and water and wastewater exposures. Is excellent as a protective coating under insulation, operating at 204°C. Outstanding resistance to wet/dry cycling conditions at these elevated temperatures.
Technical Data | ||||||
---|---|---|---|---|---|---|
Carboline Phenoline 187 VOC | ||||||
Volume Solids: | 84% +/- 2% | |||||
Theoretical Coverage Rate: | 33.1 m²/l at 25 microns 8.3 m²/l at 100 microns 5.5 m²/l at 150 microns | |||||
Allow for loss in mixing and application | ||||||
Dry Film Thickness: | 102 - 152 microns per coat | |||||
Two coats are needed for optimum performance. A third coat may be applied for additional thickness and/or service life | ||||||
VOC Values: | As Supplied: 119 g/l | |||||
Thinner 2: 20% by volume 240 g/l These are nominal values and may vary slightly with colour. | ||||||
Under Insulation Resistance: | Continuous: 204°C | |||||
Non-Continuous: 232°C | ||||||
Temperature Resistance (Immersion): | Immersion temperature resistance depends upon exposure. Consult Rawlins on Tech - 0113 2455450 (option 2) or [email protected] for specific information | |||||
Flash Point: | Part A: 11°C Part B: 15°C | |||||
Shelf Life: | Part A: Min.: 12 months at 24°C Part B: Min.: 6 months at 24°C | |||||
Storage Temperature and Humidity: | 4°-43°C | |||||
0-100% Relative Humidity |
Performance Data | |||
---|---|---|---|
Test Method | System | Results | |
Abrasion ASTM D4060 (CS17 Wheel, 1000 cycles, 1000 g load | 2 coats Phenoline 187 VOC | 95 mg loss | |
Thermal Shock, 3 cycles (-10°F to 410°F) (-23°C to 210°C) | 2 coats Phenoline 187 VOC | Unaffected except for discolouration | |
Thermal Shock, 5 cycles (-70°F to 200°F) (-57°C to 93°C) | 2 coats Phenoline 187 VOC | Unaffected except for discolouration |
Immersion Data | ||
---|---|---|
Test Method | System | Results |
Citric Acid 50%, 1-year immersion 100°F (38°C) | 2 coats Phenoline 187 VOC | Unaffected |
Corn Syrup, 1-year immersion 180°F (82°C) | 2 coats Phenoline 187 VOC | Unaffected |
Crude Oil (180°F/82°C), Modified NACE TM0174 Procedure B | 2 coats Phenoline 187 VOC | Unaffected |
Diesel (150°F/65°C), Modified NACE TM0174 Procedure B | 2 coats Phenoline 187 VOC | Unaffected |
Jet Fuel (150°F/65°C), Modified NACE TM0174 Procedure B | 2 coats Phenoline 187 VOC | Unaffected |
Curing Schedule | |||
---|---|---|---|
Surface Temp | Dry to Recoat | Maximum Recoat Time | Final Cure Immersion |
10°C | 36 Hours | 30 Days | 14 Days |
16°C | 24 Hours | 21 Days | 10 Days |
24°C | 12 Hours | 14 Days | 7 Days |
32°C | 6 Hours | 7 Days | 5 Days |
General
Steel
Stainless Steel
Product Information | |
---|---|
Mixing: | Power mix separately, then combine and power mix. |
Do not mix partial kits | |
Requires short 15 min sweat-in time | |
Thinning: | Thinning will be required to properly atomize the mixed material. Thin up to 20% (25 oz/gal) with Thinner 2 |
Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied | |
Ratio: | 2:1 Ratio (A to B) |
Pot Life: | 1 Hour at 24°C, 2 Hours at 15°C; less at higher temperatures. Pot life ends when coating loses body and begins to sag |
Conventional Spray: | Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, .070” I.D. fluid tip and appropriate air cap. Adjust air pressure to approximately 50 psi at the gun and provide 10-20 lbs. of pot pressure |
Airless Spray: | Pump Ratio: 30:1 (min.) GPM Output: 2.5 (min.) Material Hose: 3/8” I.D. (min.) Tip Size: 017”-.021” Output PSI: 1500-2300 Filter Size: 60 mesh |
Apply a “mist” bonding pass. Allow to dry approximately one minute but not long enough to allow film to completely dry. Apply crisscross multi-passes, moving gun at fairly rapid rate, maintaining a wet appearing film. Fast multi-passes may be applied until you have a wet film thickness of approximately 150-200 µ. Repeat this procedure for the second coat to obtain an 200-300 µ DFT | |
Brush: | Use medium bristle brush. Not recommended for tank lining applications except when striping welds. Avoid excessive re-brushing for best results |
Roller: | Not recommended for tank lining applications except when striping welds. Use a short-nap synthetic roller with phenolic core |
Product Conditions | |||||
---|---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity | |
Minimum | 16°C | 10°C | 10°C | 0% | |
Maximum | 32°C | 43°C | 38°C | 85% |
Clean Up
Safety
Ventilation
Caution
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Carboline Phenoline 187 VOC is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)