Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
Carboline Plasite 4301 HT is a two-component, high performance glass-flake filled coating which is designed for application over steel or concrete in extreme chemical exposures. It is resistant to a wide variety of aggressive chemicals, including organic and inorganic acids, most alkalies, and many solvents.
This product is available as POA. Click here to email us for more information.
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450 or email [email protected].
Carboline Plasite 4301 HT is a two-component, high performance glass-flake filled coating was designed for application over steel or concrete in extreme chemical exposures. It is resistant to a wide variety of aggressive chemicals, including organic and inorganic acids, most alkalies, and many solvents.
It is ideally suited for immersion service as internal steel tank linings, as well as for aggressive chemical splash, spill, and fume exposures on structural steel. Typical uses include steel tank and vat linings, secondary containment, structural steel, process floors, grating, sumps and trenches, scrubbers, and clarifiers.
Technical Data | |
---|---|
Carboline Plasite 4301 HT | |
Theoretical Coverage Rate: | 1.52-1.64 m2/l at 508 microns 1.96-2.31 m2/l at 381 microns |
Dry Film Thickness: | 381 - 508 microns per coat |
For tank linings: Two coats are recommended. For structural steel (other): One or two coats depending on the exposure For concrete: Two coats are recommended | |
VOC Values: | As Supplied: 16 g/l |
Dry Temp. Resistance: | Continuous: 149°C |
Flash Point: | Part A: 31 °C Part B: 80 °C |
Shelf Life: | 2 months |
Storage Temperature and Humidity: | 10-32 °C |
For 24-48 hours preceding use, narrow the storage temperature to 21-29°C to facilitate mixing |
Curing Schedule | |||
---|---|---|---|
Surface Temp | Dry to Recoat | Maximum Recoat | |
10°C | 12 Hours | 7 Days | |
24°C | 5 Hours | 7 Days | |
32°C | 2 Hours | 5 Days |
General
Concrete or CMU
Product Information | |
---|---|
Mixing: | This product is normally batch mixed and applied with standard airless application equipment but can be applied with plural component catalyst injection spray equipment For batch mixed, standard airless application the part A should be thoroughly mixed until uniform with a mechanical high-speed agitator. Once Part A is uniform the entire contents of part B should be added to the Part A and this catalszed material mixed with a mechanical high speed agitator until uniform and for a minimum of five minutes For plural component catalyst injection consult Rawlins on Tech - 0113 2455450 (option 2) or [email protected] |
Thinning: | Thinning is not normally required and not recommended when using plural component catalyst injection spray equipment Additive 47 at up to 5% by volume may be used for thinning when using standard airless application equipment but a reduction in the cure speed can be expected. |
Pot Life: | 30-40 minutes @ 24°C and significantly less at higher temperatures when batch mixed and applied with standard airless application equipment |
Spray Application (General): | Small quantities may be applied using a 2-gallon bottom-fed pot. Conventional atomizing spray system shall be equal to: Binks Model 2001 Gun with 59ASS Fluid Nozzle – 251 Air Cap 559SS Needle Heavy-duty trigger spring recommended. Pot pressure of approximately 50 psi (3.4 bars) Atomizing pressure of approximately 60 psi (4.1 bars). (Use standard production-type pressure pot with air motor drive agitator) Note: Application by conventional spray equipment may affect maximum film building capabilities and coverage rates |
Airless Spray: | Airless spray system requires a large capacity pump with a capacity of 3 g.p.m. (11.1 l.p.m.) similar or equal to: Graco (Bulldog may be used in certain instances) King air motor with 0.025” or larger fluid nozzle; 12in (30 cm) minimum spray width is recommended Use liquid pressure of approximately 1800 to 2200 psi (124-152 bars) All screens should be removed from pump and gun. A 3/8 in. (9 mm) diameter fluid line is recommended |
Plural Component Airless Spray: | Use a 45:1 fluid pump (less filters) on a special cart with a Binks Super Slave, 12 gal Stainless Steel hopper, air regulator assembly, up to a 100’ resin, catalyst and air hose assembly, swivel, Century Gun with T.C.Seat , needle and tip |
Brush and Roller (General): | Product may be applied using a brush or roller for small areas only |
Product Conditions | |||||
---|---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity | |
Minimum | 16°C | 10°C | 10°C | 0% | |
Maximum | 32°C | 49°C | 49°C | 80% |
Clean Up
Safety
Ventilation
Caution
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Carboline Plasite 4301 HT is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)