Carboline Plasite 7159 HAR

278PA1NL

A water-resistant epoxy coating polymerized with a polyamine type curing agent. A high performance lining for elevated temperature and pressure immersion services in high purity water, as well as the oil/water separating processes encountered in the petroleum industry. This HAR version of Plasite 7159 is extremely abrasion resistant.

Top Features

  • Easy-to-apply high performance thin film lining
  • Resists strong oxidizer and acid immersion
  • Can be air dried or force cured for prompt service
  • Outstanding abrasion resistance
Colour
Quantity

Description

Carboline Plasite 7159 HAR is a water-resistant epoxy coating polymerized with a polyamine type curing agent. A high performance lining for elevated temperature and pressure immersion services in high purity water, as well as the oil/water separating processes encountered in the petroleum industry. This HAR version of Plasite 7159 is extremely abrasion resistant.



Top Features & Benefits


  • Easy-to-apply high performance thin film lining
  • Protects I high temperature demineralized water immersion - 212°F (100°C)
  • Recommended in high pressure three phase service up to 250°F (121°C)
  • Resists strong oxidizer and acid immersion
  • Can be air dried or force cured for prompt service
  • Outstanding abrasion resistance



Preparation & Application


Remove any oil or grease from surface to be coated in accordance with SSPC-SP1.

Steel
SSPC-SP10; Surface Profile should be dense angular 2.0-3.0 mils (50-75 µ)

Aluminium
Surface shall be clean and grease-free with a blast produced anchor pattern or “tooth” as described earlier under STEEL. In addition, the blasted surface shall be given a chemical treatment such as: ALODINE 1200S available from Henkel Surface Tech IRIDITE 14-2 produced by MacDermid Incorporated OAKITE CRYSCOAT 747LTS and OAKITE CRYSCOAT ULTRASEAL produced by Oakite Products

Stainless Steel
Profile should be dense angular 2.0-3.0 mils (50-75 µ). Remove all surface contaminants that would interfere with the performance of stainless steel for the intended service such as, but not limited to, imbedded iron or chlorides.

Mixing
Thoroughly mix part A and B separately, then add part B slowly to the part A and mix completely. The coating should stand approximately 30 minutes after the curing agent has been thoroughly mixed in.

Thinning
Plasite Thinner 71 is recommended for normal application temperatures and conditions. Plastite Thinner 19 is recommended for above normal application temperatures and where tank design requires a slower evaporating thinner to help control overspray.

The amounts of thinner required will vary depending on air and surface temperatures and application equipment.

Normal application temperatures and conditions will require the addition of approximately 10% by volume with approximately 5% additional thinner added for each 5°F(3°C) of increased temperature. Airless spray equipment and above normal temperatures require additional thinning.

It is recommended that the thinner included on each order amount to approximately 20% of the coating order.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
278PA1NL
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Rust-Oleum 9100 High Performance Epoxy

A two-pack, glossy epoxy for metal, walls and floors. It is the most efficient epoxy system providing a very hard coating with high layer thickness giving lasting results with even a single coat application. 

Price £98.77
In stock

Jotun Jotamastic 90

Jotun Jotamastic 90 is a two component polyamine cured epoxy mastic coating that is a surface tolerant, abrasion resistant, high solids and high build. This Jotun product is tintable in a wide range of colours and is specially designed for areas where optimum surface preparation is not possible or desired. Provides long lasting protection in...

Price £52.14
In stock

PPG Dimetcote 9

PPG Dimetcote 9 (also known as Sigmazinc 9), is a two-component, moisture-curing zinc (ethyl) silicate coating for structural steel that can withstand substrate temperatures from –90°C (–130°F) up to 400°C (750°F), with good resistance to impact and abrasion. Anti-corrosive primer for structural steel. Specified for structural joints...

Price £270.50
In stock

Carboline Plasite 4301 HT

This high performance glass-flake filled coating was designed for application over steel or concrete in extreme chemical exposures. It is resistant to a wide variety of aggressive chemicals, including organic and inorganic acids, most alkalies, and many solvents. This product is available as POA. Click here to email us for more information....

In stock

Jotun Jotamastic 90 Alu B15 WG

Jotun Jotamastic 90 Alu B15 WG is a 'Wintergrade' version of Jotun Jotamastic 90 Alu B15 to aid application in lower temperatures and to provide faster drying and curing times. It is a two component polyamine cured epoxy mastic coating that is a surface tolerant, abrasion resistant, high solids, high build product.

Price £182.52
In stock

Carboline Thermaline 4900 Aluminum

An air-dried coating available in colours and suitable for high temperature exposures up to 525°F (273°C). Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Top Features Temperature resistance up to 273°C Air-dried curing capabilities Excellent resistance to thermal...

Price £78.38
In stock

Sherwin-Williams Dura-Plate 301S

Sherwin-Williams Dura-Plate 301S is an anticorrosive coating for long service life steel protection, normally used as an intermediate or topcoat as part of a 301 based coating system when very high edge retentive is required. It can be used for both immersion and above the waterline service in marine, offshore, construction and industrial applications.

Price £70.69
In stock

Blackfriar Matt Black Paint

Perfect for when you need a dead black matt surface. Its non-reflective finish makes it ideal for all interior surfaces such as old beams, panelling, decorative ironwork, stage scenery and darkrooms. To be used on wood and metal.

Price £14.08
In stock

Sherwin-Williams Dura-Plate 301K

Sherwin-Williams Dura-Plate 301K is a solvent-free, surface and humidity tolerant two-pack modified epoxy that can be applied without dew point restrictions and over wet steel surfaces. It is an anticorrosive coating for long service life steel protection that can be used for both immersion and above the waterline service in marine, offshore, construction...

Price £70.69
In stock

Carboline Carboguard 891

A high solids, high-build potable water coating widely used for lining interior steel and concrete tanks, valves and pipes. Top Features Excellent film build and edge protection VOC compliant to current AIM regulations Gloss finish Self-priming

Price £259.50
In stock

Jotun Norpol Accelerator 9826

Jotun Norpol Accelerator 9826 (formerly known as Jotun Accelerator DMA10) is a specially developed additive for Jotun Chemflake Special and Jotun Chemflake CV products - refer to each product data sheet for further information.

Price £30.31
In stock

Jotun Jotacote Universal N10

Jotun Jotacote Universal N10 is specially designed as a universal, all round, all year, new building coating where fast dry to handle times are required. Jotun Jotacote Universal N10 can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments and is replacing the current Jotacote Universal product.

Price £146.02
In stock

Jotun Jotamastic 87 Alu

Jotun Jotamastic 87 Alu provides long lasting protection in environments with high corrosivity. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces. It can be applied at sub zero surface temperatures.

Price £41.85
In stock

Carboline Phenoline 385

A high performance, high solids, epoxy lining that is recommended for a variety of petroleum storage products including 180°F (82°C) crude oil, demineralized water 150°F (65°C), crude/water mixtures, fuel oil, jet fuel, biodiesel, and gasoline. Top Features High solids; Low VOC formula VOC compliant Excellent resistance to petroleum...

Price £132.75
In stock

Jotun Jotamastic 90 White B16

Jotun Jotamastic 90 White B16 is a two component polyamine cured epoxy mastic coating that is a surface tolerant, abrasion resistant, high solids and high build. It has been specifically developed to meet the requirements of UK Highway Agency Item 116 for use on bridges and highway infrastructure.

Price £229.20
In stock

Carboline Plasite 4550 S

Plasite 4550 S is a 100% solids, flake filled, premium novolac epoxy coating designed for internal steel and concrete substrates. It is a two-component system consisting of four-parts by volume of Part A resin and one part by volume of Part B hardener. Tested and is approved for crude oil storage and transportation up to 350°F (177°C). This...

In stock