Carboline Plasite 9060 LT

360PA1NL

Carboline Plasite 9060 LT is a two-component, high performance tank lining with curing characteristics allowing the coating to be applied and cure at temperatures as low as 2°C while achieving unmatched chemical resistance in caustic, acid, solvent and ethanol service. Formulated for use in a large variety of facilities including waste water, chemical and fuel storage, wet-gas pipelines, rail cars, barges and ship tanks.

This product is available as POA. Click here to email us for more information

  • Outstanding overall chemical resistance
  • Superior immersion resistance
  • Excellent abrasion resistance and toughness
  • Well-suited for hydrocarbon exposures
  • Dry temperature resistant up to 121°C (continuous) and 149°C (non-continuous)
  • For industrial use only
  • Click to jump down to Technical Data

Colour
  • Current colour: White
Choose a colour
Close colour picker
  • White
  • Black
  • Grey
  • Red
  • Brown
  • Blue
Size
Finish
Quantity

Description

Carboline Plasite 9060 LT is a two-component, high performance tank lining with curing characteristics allowing the coating to be applied and cure at temperatures as low as 2°C while achieving unmatched chemical resistance in caustic, acid, solvent and ethanol service. The diversity of chemical resistance and unique low temperature curing allows the owner flexibility with their equipment. For industrial use only.



Click To Jump To Section:




Features and Benefits


  • Outstanding overall chemical resistance
  • Dense, highly cross-linked film for superior barrier protection
  • Superior immersion resistance
  • Excellent abrasion resistance and toughness
  • Well-suited for hydrocarbon exposures
  • Formulated for use in a large variety of facilities including waste water, chemical and fuel storage, wet-gas pipelines, rail cars, barges and ship tanks
  • Bis A free
  • Dry temperature resistant up to 121°C (continuous) and 149°C (non-continuous)
  • Cures down to 2°C



Product Specification


Technical Data
Carboline Plasite 9060 LT
Volume Solids: 76% +/- 2%
Theoretical Coverage Rate:

29.9 m²/l at 25 microns

6.0 m²/l at 125 microns

5.0 m²/l at 150 microns

Allow for loss in mixing and application
HAPs Values:

As supplied: 1.35 lbs/solid gallon

These are nominal values and may vary by colour

Dry Film Thickness:

127 - 152 microns per coat

Two coats are generally recommended to 200-250 microns total DFT

VOC Values:

As Supplied: 197 g/l

These are nominal values and may vary slightly with colour

Dry Temp. Resistance:

Continuous: 121°C

Non-Continuous: 149°C

Discolouration and loss of gloss is observed above 93°C

Limitiations:

Linings exposed to cargos warmer than the outside steel temperature are subject to a “cold-wall” effect. The smaller the temperature differential the less negative effect on performance.

Epoxies lose gloss, discolour, and eventually chalk in sunlight exposure

Flash Point:

Part A: 27°C

Part B: 13°C

Mixed: 32°C

Shelf Life:

Part A and B: Min. 24 months at 24°C

Shelf Life: (actual stated shelf life) when kept at recommended storage conditions and in original unopened containers



Drying Times


Curing Schedule
Surface Temp Final Cure Immersion Maximum Recoat Time Minimum Recoat Time
2°C 15 Days 10 Days 18 Hours
10°C 10 Days 7 Days 12 Hours
16°C 7 Days 5 Days 8 Hours
24°C 5 Days 3 Days 6 Hours
32°C 3 Days 1 Day 4 Hours



  • These times are based on a 125-175 microns dry film thickness and adequate ventilation for the release of solvents for proper cure
  • Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment, delamination between coats and premature failure
  • Excessive humidity or condensation on the surface during curing can interfere with the cure, can cause discolouration, and may result in a surface haze. Any haze or blush must be removed by water washing before recoating
  • If the maximum recoat time is exceeded, the surface must be abraded prior to the application of additional coats
  • Note: It is recommended to cure above 16°C for aggressive service



Curing Schedule
Surface Temp Final Cure Immersion
66°C 8 Hours
77°C 3.5 Hours
88°C 2 Hours



  • The above curing schedule may be used to force cure the coating system
  • Allow the freshly applied coating to air dry for 4 hours prior to elevating temperature
  • Elevate temperature no more than 15°C every 30 minutes
  • Force curing at temperatures approaching 88°C can result in a very slight colour change to the Plasite 9060 LT



Surface Preparation


Preparation
General:

Surfaces must be clean and dry

Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating

Steel: Immersion: SSPC-SP10 minimum Profile: 38-75 microns
Concrete or CMU:

Immersion: Concrete must be cured 28 days at 24°C and 50% relative humidity or equivalent

Prepare surfaces in accordance with ASTM D4258-92 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete

Voids in concrete may require surfacing



Application Methods


Product Information
Mixing:

Power mix separately, then combine and power mix

Use material immediately after mixing

Do not mix partial kits

Thinning:

May be thinned up to 8 oz/gal with Thinner 2

Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied

Ratio: 4:1 A:B
Pot Life:

1 Hours at 24°C

Pot life ends when coating shows dramatic changes in viscosity

Pot life times will be less at higher temperatures

Conventional Spray: Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, 0.055-0.070” I.D. fluid tip and appropriate air cap.
Airless Spray:

Pump Ratio: 30:1 (min.)

GPM Output: 3.0 (min.)

Material Hose: 3/8” I.D. (min.)

Tip Size: 0.015-0.019”

Output PSI: 2100-2300

Filter Size: 60 mesh

Brush and Roller: Not recommended for tank lining applications except when striping welds and touching up
Brush: Use a medium bristle brush
Roller: Use a short-nap synthetic roller cover with phenolic core



Application Conditions


Conditions
Condition Material Surface Ambient Humidity
Minimum 16°C 2°C 2°C 0%
Maximum 32°C 43°C 38°C 85%



  • This product simply requires the substrate temperature to be above the dew point
  • Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate
  • Special application techniques may be required above or below normal application conditions



Health and Safety


Clean Up

  • Use Thinner 2 or Acetone
  • In case of spillage, absorb and dispose of in accordance with local applicable regulations

Safety

  • Observe the precautionary notices on the container label, and read the safety data sheet before use
  • Employ normal workmanlike safety precautions

Ventilation

  • When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
  • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
  • In addition to ensuring proper ventilation, appropriate respirators must be used by all application personnel

Caution

  • This product contains flammable solvents
  • Keep away from sparks and open flames
  • All electrical equipment and installations should be made and grounded in accordance with regulations
  • In areas where explosion hazards exist, workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
  • Refer to the product data sheet and safety data sheets in the attachments section above for further details
Product Details
360PA1NL

Data sheet

Manufacturer
Carboline
For Use On
Steel, Concrete
Application Method
Brush, Roller, Spray
Sheen
Gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Mixing Ratio
4:1 A:B
Coverage
29.9 m²/l at 25 microns, 6.0 m²/l at 125 microns, 5.0 m²/l at 150 microns
Recommended Thinner/Cleaner
Carboline Thinner 2
Max. Application Temperature
Material: 32°C, Surface: 43°C, Ambient: 38°C, Humidity: 85%
Min. Application Temperature
Material: 16°C, Surface: 2°C, Ambient: 2°C, Humidity: 0%
Solids by Volume
76% +/- 2%
Heat Resistance (up-to)
Continuous: 121°C, Non-Continuous: 149°C
VOC
As Supplied: 197 g/l
Shelf Life (from date of manufacture)
24 months at 24°C
Recommended Dry Film Thickness
127 - 152 microns per coat
UN Number (Activator)
UN3066
UN Number (Base)
UN1263
Pot Life
1 Hours at 24°C
Dry to Recoat
2°C: 18 hours - 10 days, 10°C: 12 hours - 7 days. 16°C: 8 hours - 5 days, 24°C: 6 hours - 3 days, 32°C: 4 hours - 1 day
Fully Cured
2°C: 15 days, 10°C: 10 days, 16°C: 7 days. 24°C: 5 days. 32°C: 3 days
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Carboline Thinner 2

Carboline Thinner 2 is a thinner for use in industrial coatings. More Information **Available for delivery - see Delivery Options below**

Price £27.38
In stock

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £25.53
In stock