Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
In Stock and Available for Delivery
- There are no more items in your cart
- Shipping Calculated at checkout
- Sub-Total(ex. VAT)(inc. VAT)£0.00£0.00
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Description
Carboline Polyclad 952 is a two-component, epoxy lining for “dry” natural gas transmission pipelines. It is designed to increase flow efficiency of natural gas in pipelines. This lining provides a smooth surface inside the pipe that will increase flow and reduce energy cost of transporting natural gas.
Polyclad 952 offers corrosion protection of pipes during storage.
Fully meets criteria of API RP 5L2 for gas transmission pipelines.
Click To Jump To Section:
- Features and Benefits
- Product Specification
- Drying Times
- Surface Preparation
- Application Methods
- Application Conditions
- Health and Safety
Features and Benefits
- Improves flow efficiency in gas pipes
- Excellent flow and levelling
- Single-coat application
- Hard, smooth, glossy finish
- Excellent abrasion resistance
- Meets all criteria of API RP 5L2
- Corrosion prevention during storage
Product Specification
| Technical Data | |
|---|---|
| Carboline Polyclad 952 | |
| Volume Solids: | 75% +/- 1% |
| Theoretical Coverage Rate: | 29.5 m²/l at 25 microns 14.8 m²/l at 50 microns 4.9 m²/l at 150 microns |
| Allow for loss in mixing and application | |
| Primer: | Self-priming |
| HAPs Values: | 1.93 lbs/solid gallon |
| Dry Film Thickness: | 51 - 152 microns per coat |
| VOC Values: | As Supplied: 213 g/l Thinner 2: 12 oz/gal - 272 g/l |
| Dry Temp. Resistance: | Continuous: 120°C |
| Flash Point: | Part A: 80°C Part B: 87°C |
| Shelf Life: | Part A and B: Min 12 months at 24°C When kept at recommended storage conditions and in original unopened containers |
| Storage and Humidity: | 4-43°C 0-100% Relative Humidity |
| Performance Data | ||
|---|---|---|
| Test Method | System | Results |
| API 5L2 | One coat Polyclad 952 | Pass |
Drying Times
| Curing Schedule | |||
|---|---|---|---|
| Surface Temp | Dry to Handle | Dry to Touch | |
| 23°C | 11 Hours | 3 Hours | |
| 32°C | 5 Hours | 2 Hours | |
Surface Preparation
| Preparation | |
|---|---|
| General: | Surfaces must be clean and dry before abrasive blasting Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating |
| Steel: | SSPC-SP6, NACE 3, Sa 2 Surface Profile: 30-63 microns |
Application Methods
| Product Information | |
|---|---|
| Mixing: | Power mix part A separately, then combine part B in to part A and power mix Do not mix partial kits Mix ratio by volume is 2 to 1 |
| Thinning: | Thinning may be required to properly atomize the mixed material Thin up to 10% (13 oz/gal) with Thinner 2 or Thinner 76 Use of thinners other than those supplied by Carboline may adversely affect product performance and void product warranty, whether expressed or implied |
| Pot Life: | 3 Hours at 24°C usable pot life |
Application Conditions
| Conditions | ||||
|---|---|---|---|---|
| Condition | Material | Surface | Ambient | Humidity |
| Minimum | 16°C | 10°C | 10°C | 0% |
| Maximum | 32°C | 52°C | 49°C | 90% |
- This product simply requires the substrate temperature to be above the dew point
- Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate
Health and Safety
Clean Up
- Use Thinner 2 or Acetone
- In case of spillage, absorb and dispose of in accordance with local applicable regulations
Safety
- Observe the precautionary notices on the container label, and read the Material Safety Data Sheet before use
- Employ normal workmanlike safety precautions
Ventilation
- When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured
- The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
- User should test and monitor exposure levels to insure all personnel are below guidelines. If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator
Caution
- This product contains flammable solvents
- Keep away from sparks and open flames
- All electrical equipment and installations should be made and grounded in accordance with regulations
- In areas where explosion hazards exist, workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
Product Details
1073A1NL
Data sheet
- Manufacturer
- Carboline
- Water / Solvent Based
- Solvent
- For Use On
- Steel
- Application Method
- Spray, Airless Spray, Brush
- Sheen
- Gloss
- Colour
- Standard / Ready Mixed
- Single, Two or Three Pack
- Two-Pack
- Mixing Ratio
- 2 to 1
- Coverage
- 29.5 m²/l at 25 microns, 14.8 m²/l at 50 microns, 4.9 m²/l at 150 microns
- Recommended Thinner/Cleaner
- Carboline Thinner 2, Thinner 76
- Max. Application Temperature
- Material: 32°C, Surface: 52°C, Ambient: 49°C, Humidity: 90%
- Min. Application Temperature
- Material: 16°C, Surface: 10°C, Ambient: 10°C, Humidity: 0%
- Solids by Volume
- 75% +/- 1%
- Heat Resistance (up-to)
- Continuous: 120°C
- VOC
- As Supplied: 213 g/l
- Shelf Life (from date of manufacture)
- 12 months at 24°C
- Recommended Dry Film Thickness
- 2 - 6 mils (51 - 152 microns) per coat
- Touch Dry (at 23°C)
- 3 Hours
- Dry to Handle (at 23°C)
- 11 Hours
- Pot Life
- 3 Hours at 24°C
- Brand
- Carboline
Be the first to ask a question about this product!
IMPORTANT SHIPPING & DELIVERY INFORMATION
Carboline Polyclad 952 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
You might also like
Carboline Thinner 76
Carboline Thinner 76 thinner for use in industrial coatings. More Information Delivery Info
£57.16 (incl. VAT)
£47.63 (ex. VAT)
In Stock and Available for Delivery