Carboline Thinner 2
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
Carboline Thermaline 4900 is a single package, air-dried coating available in colours and suitable for high temperature exposures up to 260°C. Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings.
Please note: Colours are sold in the nearest tin size but actual paint volume per tin may vary up to 10% depending on colour.
Carboline Thermaline 4900 is a single package, air-dried coating available in colours and suitable for high temperature exposures up to 260°C. Air-drying characteristics allow for faster handling of in-shop applications than with other high-temperature coatings. Heat cure above 149°C is recommended and will impart added strength and integrity to the coating.
**most other colours resistant up to maximum 232°C
Technical Data | |
---|---|
Carboline Thermaline 4900 | |
Primer: | Self-priming on stainless steel, aluminum and metalized surfaces For carbon steel, apply over recommended zinc primer. A mist coating may be required to minimize bubbling over inorganic zinc primers |
Topcoats: | Not applicable |
Solid(s) Content: | By Volume 48% +/- 2% |
Theoretical Coverage Rate: | 15.7 m²/l at 25 microns 10.5 m²/l at 38 microns 7.9 m²/l at 50 microns Allow for loss in mixing and application |
Dry Film Thickness: | 1.5 - 2 mils (38 - 51 microns) per coat Don't exceed 2.5 mils (63 microns) in a single coat. Excessive film thickness over inorganic zincs may increase damage during shipping or erection |
VOC Values: | As Supplied: 528 g/l Thinner 235: 22 oz/gal (17%): 4.8 lbs/gal Thinner 25: 22 oz/gal (17%): 581 g/l Thinner 25: 8 oz/gal (6%): 550 g/l These are nominal values and may vary slightly with colour |
Flash Point: | 25°C |
Shelf Life: | 24 months at 24°C |
Curing Schedule | ||||
---|---|---|---|---|
Surface Temp. | Dry to Topcoat with Itself | Dry to Touch | ||
25°C | 4 Hours | 1 Hour |
Preparation | |
---|---|
General: | Surfaces must be clean and dry Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating |
Steel: | SSPC-SP10 with 0.5-1.0 mils (12-25 microns) surface profile Prime with specific Carboline primers as recommended by Rawlins on Tech - 0113 2455450 (option 2) or [email protected] |
Product Information | |
---|---|
Mixing: | Thoroughly mix to a uniform consistency prior to use |
Thinning: | Normally not required May be thinned up to 22 oz./gal. (17%) by volume with Thinner 25 for ambient conditions. For “hot” applications exceeding 66°C use Thinner 235 instead Use Thinner 238 up to 5% (6 oz) for brush or roller application. (Note: Shake Thinner 238 just prior to use) Use of thinners other than those supplied or recommended by Carboline may adversely affect product performance and void product warranty, whether expressed or implied |
Ratio: | N/A |
Conventional Spray: | Use DeVilbiss P-MBC, E-needle and tip, and a 704 air cap or equal Use adequate air volume for proper equipment operation. Hold gun 10-12” from the surface and at right angles. Lap each pass 50%. Apply 4.0-5.0 wet mils to obtain desired dry film |
Airless Spray: | Pump Ratio: *30:1 GPM Output: *3.0 Material Hose: 1/4" I.D. (6.4 mm) minimum Tip Size: *0.011" - 0.015" Output PSI: *1,800 - 2,700 Filter: *60 mesh *The equipment details listed above are intended to be used as guidelines. We recommend adjusting spray equipment and techniques as needed to provide the correct dry film thickness and the desired appearance. PTFE packings are recommended and available from equipment manufacturers |
Brush and Roller: | Recommended for touch-up of small areas or where spray application is not permitted. Avoid excessive re-brushing or re-rolling |
Brush: | Use a medium bristle brush |
Roller: | Use a short-nap mohair roller cover with phenolic core |
Conditions | ||||
---|---|---|---|---|
Condition | Material | Surface | Ambient | Humidity |
Minimum | 13°C | 4°C | 4°C | 0% |
Maximum | 35°C | 149°C | 49°C | 90% |
Clean Up
Safety
Ventilation
Caution
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Carboline Thermaline 4900 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
Carboline Thinner 25 is a thinner for use in industrial coatings.More Information Delivery Info
£39.16 (incl. VAT)
£32.63 (ex. VAT)
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)