
Rust-Oleum Mathys Noxyde Fleece
We no longer stock this product, but can recommend Rust-Oleum Mathys Noxyde Tape as a great alternative.
OPEN AS USUAL DURING LOCKDOWN #3
Rust-Oleum Mathys Noxyde is a single pack, water-based elastomeric coating with unequaled corrosion protection designed for spraying, offering 20 years of protection with excellent waterproofing and elasticity.
20KG sizes are temporarily unavailable; please contact our technical team regarding 20KG sizes on 0113 2455450 (option 2) or send a message to [email protected]
Rust-Oleum Mathys Noxyde is a water-based, single-component paint, designed for easy spray application and yet gives the same protection as a complicated and more expensive polyurethane systems. Rust-Oleum Mathys Noxyde forms a thick anticorrosive membrane that offers excellent protection against water, salt spray and aggressive environments. Independent research as per the ISO 12944 standard demonstrates that Noxyde is the absolute BEST in corrosive protection - it even offers more than 20 years of protection in the highest corrosion class C5-M.
Rust-Oleum Mathys Noxyde combines flexibility, strong adhesion, water resistance, excellent edge coverage and anti-corrosive pigments while requiring minimal surface preparation. Rust-Oleum Mathys Noxyde is a single pack water-based elastic coating ideal for use on metal cladding, metal roofs, bridges, silos, electrical isolation and more made from iron, steel, copper, aluminium, plastisol, zinc, lead, galvanised metal and PVDF (with a special primer).
* All guarantees are subject to approval by our Technical Department prior to purchase and/or use.
30 years track record!
Noxyde has been tested by many institutes and the results are phenomenal with reports of “unsurpassed corrosion control”. Since 1972, it has been applied all over the world in many different climates, from very hot and dry to humid, rural-coastal, onshore and offshore... No impact upon the product's effectiveness was recorded, therefore it is the number one choice for metal protection. See Project References in the "Attachments" section above for details of Noxyde used on the Golden Gate Bridge in San Francisco, and storage tanks in Rotterdam harbour.
Rust-Oleum Mathys Noxyde is a premium, state-of-the-art, easy-to-use product ideal for long-term corrosion protection of metal surfaces. Its unique formulation performs like no other coating on the market and offers unsurpassed rust protection with minimal labour. It is an excellent over coating and alternative to sandblasting, a more economical solution to epoxy/polyurethane coatings.
* All guarantees are subject to approval by our Technical Department prior to purchase and/or use.
TECHNICAL DATA | |
---|---|
Density: | 1,2 - 1,3 |
Gloss Level: | Satin |
Gloss level at 60º: | 20.00% |
Corrosion Class: | C5 very high protection |
Solids content in volume: | 55 % ± 3 % |
Solids Content in weight: | 62 % ± 3 % |
DRYING TIMES AT 20°C/RH 50% | |
---|---|
Touch dry: | 1,5 hours |
Dry to handle: | 3 hours |
Dry to recoat: | 24 hours |
Fully cured: | 2 weeks |
Recommended Wet Film Thickness
320 μm
Recommended Dry Film Thickness
175 μm
THEORETICAL CONSUMPTION | |
---|---|
Brush/roller: | 200 - 300 g/m²/coat |
Airless: | 300 - 500 g/m²/coat |
Total consumption for optimal rust preventive protection: | 800 g/m² = 350 μm dry film thickness |
Practical Consumption
Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.
Surface Preparation
Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam) cleaning (max. 200 Bars) in combination with appropriate detergents. The substrate has to be dust free and made rust free by means of sandblasting (Sa2, St2) or high pressure water jetting (min. 600 Bars). After jetting, the substrate has to be dust free. On new galvanised surfaces, new zinc, aluminium, stainless steel, apply first a coat of Pegalink. On ferrous substrates, apply Noxyde in red or grey as the first coat. In all instances apply contrasting Noxyde colours for subsequent layers.
Directions For Use
To ensure homogeneity, coating materials should be thoroughly stirred prior to use.
Application Conditions
Temperature between 8 and 55°C / Air humidity max. 80% R.H.
The substrate temperature must be at least 5°C above dew point.
Application & Thinning For Brush Applications
Undiluted as a rust preventive paint.
Diluted with approximately 25% volume water as an adhesion primer (consumption about 100 g/m²).
Application & Thinning For Roller Applications
Undiluted as a rust preventive paint. Diluted with approximately 25% volume water as an adhesion primer (consumption about 100 g/m²)
Application & Thinning For Airless Spray Applications
Undiluted. Nozzle: 13 - 17 / Pressure: min. 170 bars. Nozzle and pressure can vary depending on the type of substrate, equipment and the experience of the applicator.
Cleaning of Equipment & Spills
Water
Notes
When used for interior works, provide for adequate ventilation.During work stoppage, fully immerse brush or nozzle in water. Product is recoatable after 24 hours with itself, Coating PRT, high gloss alkyd enamels, high and satin gloss acrylic dispersion paints.
SAFETY DATA | |
---|---|
VOC level: | 15 g/l |
VOC readymix: | 15 g/l |
VOC category: | A/i |
VOC limit: | 140 g/l |
Grenelle: | Exterior |
Flashpoint: | Not flammable |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
![]() | Question:
Hi there. Would this require an airless spraygun? Thank you. |
Answer:
Yes, apply undiluted using a 13 - 17 Nozzle / Pressure: min. 170 bars. Nozzle and pressure can vary depending on the type of substrate, equipment and the experience of the applicator. | |
![]() | Question: Is Noxyd suitable for painting over existing Durbar chequerplate (walkway floorplate) and steel joists - presumed original painted with Red Oxide Primer around 40 years ago. What preparation would be necessary? Do you carry out paint analysis on existing decorations to ensure compatibility? Thank you. |
Answer: Rust-Oleum Mathys Noxyde cannot be used as a floor coating so for the chequer plate we would suggest something like Rust-Oleum 9200 Rust-O-Thane instead. Rust-Oleum Mathys Noxyde should be fine for the steel joists assuming these aren't walked on. Paint analysis normally wouldn't be required for Noxyde but we do recommend a test area is carried out prior to full application to ensure compatibility, adhesion, appearance, etc. If you would like to provide some more information about the project and your requirements we can be more specific or arrange a site visit if necessary. | |
![]() | Question: Hi is there a product I can use on the Noxyde to make it a gloss finish? Many Thanks |
Answer: Rust-Oleum Mathys Noxyde is recoatable after 24 hours with itself, Coating PRT, high gloss alkyd enamels, high and satin gloss acrylic dispersion paints. Alternatively you could instead use Rust-Oleum Pegarust instead of Noxyde if this is an option as this comes in a gloss finish as standard. | |
![]() | Question: Would this be suitable for painting a shipping container |
Answer: Yes. | |
![]() | Question: Hi can you mix colours as I need some colours that aren't on the colour list. As they are for a nursery I need pink blue and green which are colours on their signage. Also what area does the 20kg tins cover for a spray application. Many thanks ste |
Answer: Rust-Oleum Mathys Noxyde is only available in the standard colours shown unless you require more than 100kg of each colour at which point it can be manufactured to most RAL and BS colours on a 2 - 3 week lead time. Rust-Oleum Mathys Metal Cladding Primer and Rust-Oleum Mathys Metal Cladding Topcoat may be of interest for your project and can be mixed individually to most RAL, BS, NCS and bespoke colours. | |
![]() | Question: Hello, is this product suitable for painting a steel pick up bed on a 4x4 & what type of finish i.e gloss, matt, satin etc. Kind regards Darren |
Answer: No, we would instead recommend Smartkote Protectakote UVR for this application. | |
![]() | Question: Is your Noxyde paint suitable for use on acid primed aluminium greenhouse ? |
Answer: By 'acid prime' we are assuming you've used some sort of single pack, acid etch primer. We'd need a copy of the Technical Data sheet to confirm potential compatibility but subject to it being acceptable Rust-Oleum Mathys Noxyde is designed for airless spray application, if you intend to apply by brush or roller then Rust-Oleum Mathys Noxyde Peganox would be more suited. | |
![]() | Question: Can rust oleum mathys noxyde paint be used to paint a metal narrow boat below the water line .many thanks for any information on this request... |
Answer: No, Rust-Oleum Mathys Noxyde would definitely not be suitable for this, please call our Technical Department on 0113 2455450 for suitable options. | |
![]() | Question: Can this be painted onto Plastisol coating on roof cladding? |
Answer: Yes, Rust-Oleum Mathys Noxyde is ideally suited to this application. It can be applied directly to correctly cleaned and preparated Plastisol Colorcoat HP200 and HPS200 Metal Cladding. HP200 is easily recognised by its classic ‘leathery’ surface texture and has been available since 1987, HPS200 has been available from 1998 and has a ‘dimpled’ surface texture and looks quite different from the traditional ‘leathergrain’ Plastisol. Other metal cladding types such as PVDF, PVF2, Polyester, Polyurethane, Power Coating, etc. require special consideration and in most instances will require a primer coat prior to applicaiton. These surfaces are usually easily recognisable by their ‘smooth’ appearance, however due to the nature of these cladding types we ALWAYS recommend our Technical Department is consulted for advice prior to commencement of works. | |
![]() | Question: We have gates which have some rust and have previously been painted with Hammerite. Can we use this paint sprayed directly onto the (cleaned) prepainted and rusty surfaces? |
Answer: Yes, as long as you prepare the surface to remove any loose and flaking paint and rust, Rust-Oleum Mathys Noxyde can be applied directly. Surface Preparation should be as follows; Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam) cleaning (max. 200 Bars) in combination with appropriate detergents. The substrate has to be dust free and made rust free by means of sandblasting (Sa2, St2) or high pressure water jetting (min. 600 Bars). After jetting, the substrate has to be dust free. On new galvanised surfaces, new zinc, aluminium, stainless steel, apply first a coat of Rust-Oleum Mathys Pegalink Universal Adhesion Primer. On ferrous substrates, apply Noxyde in red or grey as the first coat. In all instances apply contrasting Noxyde colours for subsequent layers. | |
We no longer stock this product, but can recommend Rust-Oleum Mathys Noxyde Tape as a great alternative.
Rust-Oleum Mathys Noxyde Peganox is a water based, low VOC, single component, elastomeric coating that provides rust-proofing, corrosion and waterproofing protection optimized for brush or roller application. It forms an anti corrosive membrane that has a high resistance to water, salt spray, acid and aggressive environments making it...
Rust-Oleum Mathys Noxyde Pegarust is a rust preventing coating that is the solvent-based version of Rust-Oleum Mathys Noxyde that can be applied by brush, roller or spray in cold temperatures down to 0°C or on damp surfaces by brush, roller or spray. Excellent corrosion protection and waterproofing Approved for corrosion class C5-M...
Rust-Oleum Mathys Noxyde Tape is a self-adhesive tape made of a butyl rubber compound protected by a Fleece in Polypropylene used for reinforcement of overlaps of metal cladding roof and wall panels in combination with the Noxyde coating system. Easy to apply Excellent adhesive properties, even at low temperatures Excellent heat...
Please complete the following questions:
Please complete the following questions: