Axalta ViterShield 178 HS Epoxy Primer/Finish is a two-pack epoxy, high solids, zinc phosphate primer or primer/finish for steelwork. High performance, low VOC coating to help meet SED requirements.
Provides a high build single coat/two coat high performance system for steelwork
Exceptional sag resistance
Excellent cure speed and high build properties
Good resistance to undercutting from damaged areas
Overcoatable with most epoxy, acrylic or polyurethane coatings
Hard Dry in approximately 3hrs at 23°C
Use as a base coat for most thin film intumescent coatings
Axalta ViterShield 178 HS Epoxy Primer/Finish is a two-pack epoxy, high solids, zinc phosphate primer or primer/finish for steelwork. High performance, low VOC coating to help meet SED requirements.
Axalta ViterShield 178 HS Epoxy Primer/Finish has exceptional sag resistance, as well as excellent cure speed and high build properties. It is overcoatable with most epoxy, acrylic or polyurethane coatings and can be used as a base coat for most thin film intumescent coatings.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical Department on 0113 2455450 (option 2) or send a message to [email protected] for more information.
A two pack epoxy, high solids, zinc phosphate primer or primer/finish for steelwork
High performance, low VOC coating to help meet SED requirements
Exceptional sag resistance
Excellent cure speed and high build properties
Good resistance to undercutting from damaged areas
Overcoatable with most epoxy, acrylic or polyurethane coatings
Use as a base coat for most thin film intumescent coatings
Hard Dry in approximately 3hrs at 23°C
Product Specification
Technical Data
Axalta ViterShield 178 HS Epoxy Primer/Finish
Volume Solids
70 ± 2%
VOC Content
277 + 20 g/litre
SG
1.48 – 1.52 kg/lt mixed
Storage Conditions
Store in dry, cool conditions and protect from frost
Shelf Life
Minimum 12 months if stored as above in unopened containers
Flash Point
23-60°C
Pot Life
3 hours at 23°C
Film Thickness Range And Coverage
Film Thickness Range & Coverage
Dry Film Thickness
Wet Film Thickness
Theoretical Coverage
Minimum
75 µm
107 µm
9.3 m 2/litre
Maximum
280 µm
400 µm
2.5 m 2/litre
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated
Drying Times
Drying Times
Applied to 100 microns DFT
10℃
23℃
35℃
Dust Free
2 hr
1 hr
30 min
Hard Dry
6 hr
3 hr
1.5 hr
Overcoating
Minimum*
6 hr
3 hr
1.5 hr
Maximum
Indefinite if surface is clean and sound
*See Product Notes. Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
Surface Preparation
Blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50-75 microns
All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams
Mixing
Mixing Ratio:
Base 6178 - 5 parts by volume
Hardener 6400 003 - 1 part by volume
Notes:
Mix only in the proportions stated, mixing each component individually then together using a mechanical agitator
Agitate periodically during use to ensure product remains homogeneous
Only apply in conditions of good ventilation which must be maintained during drying and curing
Do not apply when rain, mist, sleet or snow are imminent
During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
Only apply this product when the above conditions can be maintained throughout the critical application and drying/curing process
Paint temperature should ideally be at a minimum of 15ºC
Application Methods
Airless Spray: Output fluid pressure at tip 2200 psi, Tip Size: 13 thou (0.33mm) for dft’s 75-125um; 15-17 thou (0.38-0.43mm) for 125-280um
Thinning of the coating will reduce the build qualities
Application by brush/roller will result in a reduced film thickness and is recommended only for small areas of touch up/remedial work
May be overcoated with itself or other products from the ViterShield, ViterSeal or ViterThane range
If overcoating with ViterThane PLV or PLS, allow a minimum of 12 hours at 23°C when the primer has been applied to 100 microns dft. Allow longer drying and overcoating times at higher dft’s and lower temperatures
The compatibility of overcoating should be confirmed prior to application
Certain configurations of steelwork may mean that the primer will have to be applied in more than one coat to achieve the higher film thicknesses
Whilst this product will display a matt finish at a dry film thickness of 75 microns, application to a dry film thickness above 125 microns will provide a low sheen finish, the degree of which may vary
Do not apply or cure below 5°C, temperatures above 10°C recommended
Like all epoxy coatings, this product will chalk on prolonged exterior exposure, the degree of which is subject to atmospheric conditions
Health & Safety
Containers are provided with safety labels which should be observed
Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Product Details
5332-874835
Data sheet
Manufacturer
Axalta Coating Systems
For Use On
Steel
Application Method
Airless Spray
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Pack Size
20L
Minimum Applied Thickness
75µm DFT/107µm WFT
Maximum Applied Thickness
280µm DFT/400µm WFT
Mixing Ratio
5 Base : 1 Hardener
Touch Dry (at 20°C)
60 mins
Coverage
2.5m²/litre - 9.3 m²/litre dependand on film thickness
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Axalta ViterShield 178 HS Epoxy Primer/Finish is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Axalta ViterThane PLS Recoatable PU Finish, A two pack recoatable polyurethane semi-gloss finish for use on protective systems for steelwork.Excellent colour retention and indefinitely overcoatable. Excellent chemical resistance and low temperature cure. An aliphatic polyurethane providing a tough and durable semi-gloss finish with...
Axalta 1031 Thinner, for use with the Axalta range of coatings, has a specially formulated blend of solvents designed to mix with its compatible paint/coating to create an optimal consistency for application whether it be for brush, roller or spray. Can also be used for the cleaning of some surfaces prior to application of the coating...
Axalta ViterThane PLV Finish is a two pack recoatable polyurethane gloss finish for use on protective systems for steelwork.Provides a tough and durable gloss finish together with excellent gloss and colour retention Excellent chemical resistance and low temperature curing down to -5ºC Withstands dry heat up to 150ºC (discolouration may...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...