A rust preventing coating that is the solvent-based version of Rust-Oleum Mathys Noxyde that can be applied by brush, roller or spray in cold temperatures down to 0°C or on damp surfaces by brush, roller or spray.
Rust-Oleum 9100 High Performance Epoxy
A two-pack, glossy epoxy for metal, walls and floors. It is the most efficient epoxy system providing a very hard coating with high layer thickness giving lasting results with even a single coat application.
Rust-Oleum 9100 High Performance Epoxy is a two-pack, glossy epoxy for metal, walls and floors. It is the most efficient epoxy system providing a very hard coating with high layer thickness giving lasting results with even a single coat application. Also ideal as a glossy floor paint for garages, warehouses, indoor car parks etc. Optimal protection can be achieved in only one or two layers.
With Rust-Oleum 9100 Epoxy you can save time on;
Application - Apply in one thick layer if required
Mixing - Easy 1:1 mixing ratio, no waste and no thinning required.
Surface Preparation - Can be applied directly to sound rusted surfaces without the need for blasting.
Maintenance - Longer lasting results means reduced downtime for repairs and re-coating.
Features & Benefits
- Single coat application directly over rusted surfaces
- Excellent results with minimal surface preparation
- Full colour intensity in one coat
- 1:1 mixing ratio
- Very resistant to abrasion
- Excellent resistance against immersion; can be used in swimming pools
- Resistant to oils, solvents and many chemicals
- Suitable for frequent cleaning with chemicals
- Tintable to virtually any colour
- Winter grade & high solids versions available
Choice of 3 versions:
- 9101 - Standard activator ideal for most circumstances
- 9101HS – Better coverage and low VOC
- 9101WG - For application temperatures down to 0°C
Rust-Oleum 9100 High Performance Epoxy is designed for application on manually prepared rusted steel surfaces and can also be used on clean, blasted steel, primed steel, concrete and previously coated surfaces. Rust-Oleum 9100 Topcoats are primarily intended for brush and airless spray application and can also be applied by roller.
Rust-Oleum 9100 High Performance Epoxy offers excellent protection against strong chemicals, acids, alkalis and solvents; frequent product spillage and chemical cleaning; high humidity and moisture conditions. If good U.V. resistance is required Rust-Oleum Polyurethane Topcoats 9200, 9600 or 9900 should be applied (except for the clear coatings).
Rust-Oleum 9100 High Performance Epoxy can be applied on cleaned, sound mineral substrates, sound, well prepared previous coatings; porous substrates should be primed with Rust-Oleum Impregnation Primer 5401; very dense substrates, like ceramic tiles, should be primed with Rust-Oleum Super Adhesive 3333.
- Light rusted metal - 9169 Epoxy Rust primer
- Bare metal - 9170/9180 Epoxy Metal primer
- Smooth concrete - 3333 Epoxy Adhesion primer
Please note: The outdoor durability and chemical resistance of the system can be further improved by the application of an additional topcoat Rust-O-Thane 9200 or 9600.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller, Spray
- 6m² per litre
- Touch Dry
- 6 Hours
|Elias on 28/01/2019|| |
Hi, Can this be applied on concrete floor that had previously been painted? The previous paint job was badly done and has areas of discolouration.
Yes, as long as the existing coating is sound, well adhered and compatible (carry out a test area) - Sand previous coatings, which are in good condition to remove gloss and to roughen the surface slightly before application.
|Emma Roberts on 01/07/2018|| |
Can it be used to cover a concrete floor for dogs to walk on that will be mopped with disinfectant 3-4 times a day?
Yes this should be suitable as long as adequate preparation is carried out. Our Technical Department can issue a list of chemicals and this products performance with them if required to ensure your disinfectant would be suitable. Please note this product is not UV stable so if exposed to sunlight, topcoat with Rust-Oleum 9200 Rust-O-Thane.
|marlene ford on 04/08/2016|| |
Question: Hi, could you tell me whether this paint could be used on wooden floors please? Thank you Marlene
Answer: No it can't. If you'd like to contact our Technical Team on 0113 2455450 or [email protected] so we can get some more information about your project, we will be able to offer a suitable alternative.
|Micaela on 13/04/2016|| |
Question: Can this product be used to paint over marble ??
A primer must be applied to the marble before application of Rust-Oleum 9100 High Performance Epoxy is carried out. If the marble is very smooth, use Rust-Oleum 3333 Super Adhesion Primer. If it is rough, textured or has a profile, use Rust-Oleum 3366 Epoxy Powerfloat Floor Primer Rapid.
International Interseal 670HS (Winter Grade) is supplied with a winter grade curing agent to enable more rapid cure at lower temperatures. The product is still a low VOC, two component high build, high solids surface tolerant epoxy maintenance coating, for application to a wide variety of substrates including hand prepared rusty steel and a wide range of...
A metal primer with surface tolerant properties, can also be used as an intermediate coat, or self-priming finish over steel and zinc primers. Top Features Ready to apply after mixing Economical fit for use epoxy Used as a primer, intermediate, or finish coat VOC compliant to current AIM regulations
An all-purpose immersion-grade epoxy that can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Top Features Low temperature cure (20°F) Excellent corrosion protection Excellent application characteristics Fast recoat times
A high solids epoxy lining with exceptional chemical resistance. Primarily as a tank lining, it is recommended for storage of crude oil (180°F/82°C), demineralized water (150°F/65°C), tap water (200°F/93°C) food and beverage industries, and water and wastewater exposures. Top Features High solids; Low VOC formula VOC compliant Excellent...
International Intertuf 16 is a one component, high build cold applied bituminous coating for use as an economical coating ideally suited for the protection of interior steel surfaces in enclosed areas such as tanks for storage of sea water, immersed piping and structural steelwork.
A high performance direct-to-metal silicone/polyurethane alkyd finish. Perfect for the protection and decoration of ferrous metals in many home projects such as fencing, gates and other ironmongery. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004 Advantages Outstanding application properties Excellent exterior...
A quick drying, White Spirit based alkyd topcoat with good light and weather resistance that is suitable for interior and exterior use. Top Features May be diluted up to 20% 24 month shelf life High gloss finish
An all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance and fast recoat times. Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Top Features Excellent corrosion protection Excellent application characteristics Fast...
A hammered finish maintenance paint for metal with superior metal protection, even direct to rust. Rust-Oleum CombiColor Hammertone is a primer and topcoat in one, ideal for various little projects. For a satin, matt or gloss finish, please check out Rust-Oleum CombiColor paint.
A high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Top Features Fast curing rate increases throughput Excellent abrasion resistance Compliant with AWWA C222 Compliant with EN 10290 This product is available as POA. Click here to email us...
A highly cross-linked, glass-flake filled polymer that offers exceptional barrier protection and resistance to wet/dry cycling at elevated temperatures. Suitable for insulated or uninsulated pipes, stacks and equipment operating up to 450°F (232°C). Top Features Temperature resistance up to 232°C Excellent resistance to thermal shock...
Cromadex 690 Two Pack Polyurethane Gloss Primer Finish is a two pack gloss primer finish; it is a high build finish making it suitable for blasted steel. The product contains zinc phosphate giving added corrosion resistance for greater durability.Cromadex 690 is available in full Cromadex range of colours, including BS, RAL, and special matches all in a...
A highly chemical resistant epoxy mastic coating with exceptionally versatile uses in all industrial markets. Carboline Carboguard 890 LT is self-priming and suitable for application over most existing coatings, and tightly adherent to rust. Top Features Excellent chemical resistance Self-priming capability Very good abrasion resistance...
This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Marathon 500 as a great alternative. Jotun Marathon is a two component polyamine cured epoxy coating that is a high solids, high build, glass flake reinforced product. It is scratch and abrasion resistant and is suitable for...
A higher solids, better coverage and lower VOC content product than the standard 9100 Epoxy. Two-pack, glossy epoxy coating for metal, walls and floors. The most efficient epoxy system providing a very hard coating with high layer thickness for lasting results even with a single coat application.