An epoxy lining for “dry” natural gas transmission pipelines. It is designed to increase flow efficiency of natural gas in pipelines. It fully meets criteria of API RP 5L2 for gas transmission pipelines. Top Features Improves flow efficiency in gas pipes Excellent flow and leveling Single-coat application Hard, smooth, glossy finish
Teamac Farm Oxide Paint
Teamac Farm Oxide Paint is an economical, general purpose, versatile product giving economical protection and decoration which can be used for the maintenance of structural steel, cladding etc. when applied to properly prepared surfaces. May be used coat on coat and dries to a durable gloss finish. Can be applied directly to prepared iron or steel.
Teamac Farm Oxide Paint is a general purpose, versatile product giving economical protection and decoration which can be used for the maintenance of structural steel, cladding etc. when applied to properly prepared surfaces. May be used coat on coat and dries to a durable gloss finish.
Teamac Farm Oxide Paint can be applied directly to prepared iron or steel. For greater protection prime with Teamac Zinc Phosphate Metal Primer.
- High opacity pigments
- Direct to steel
- Good coverage
Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
Bare steel should be free from dust, rust and scale. Blast cleaning to SA 2½ is recommended. If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree. Any oil or grease should be removed with Coo-Var Degreaser before de-rusting. Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts, welds etc. Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.
As dictated by normal good painting practice. Care must be taken during application that the temperature is above the dew point to avoid any contamination. In confined spaces, provide adequate ventilation during application and drying.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Brush, Roller
- 11m² per litre
- Touch Dry
- 5 Hours
|Heather on 23/02/2018|| |
Is farm oxide paint suitable for galvanised steel
Teamac Farm Oxide Paint is perfectly acceptable onto Galvanised steel, however before application the galvanised surface must be either:
A. Cleaned and T-washed if brand new.
|linda on 23/03/2017|| |
Question: is the farm oxide green paint suitable for painting wood at all? We have used the metalastic paint in the past but appears quite expensive now. how different are the colours, we used mid Brunswick green,
Teamac Farm Oxide will be OK on wood, if applying directly thin the first coat. The colours should be similar but wont be an exact match.
A surface tolerant from Jotun that is a high build epoxy coating suitable for environments with very high corrosivity, such as areas in the splash or tidal zones. Jotun Marathon 500 is a two component polyamine cured epoxy coating. It's a surface tolerant, high solids, high build product that will continue to cure even when immersed in water.
Thermo-Lag 3000-P is a petrochemical grade, 100% solids epoxy based intumescent designed to fireproof steelwork for up to a 4-hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways. Top Features UL...
A rust preventing primer. Typically used as a primer above water line on areas like superstructure, topside, deck, stores room, cargo hold etc. Top Features Quick drying, White Spirit based alkyd primer May be topcoated with alkyd paints as recommended Can be thinned
Everbuild 901 Black Bitumen Paint is a solvent based, full bodied black bitumen paint, When dry, the product forms an odourless and taint free bitumen film suitable for the protection of metals, concrete roofing, felt, fibre cement, corrugated iron, asphalt and wood against water attack.
A high performance immersion-grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures. It is typically used on hot steel substrates under insulation operating continuously up to 400°F/204°C. Top Features Continuous temperature resistance to 204°C Very good flexibility Acceptable for use...
A highly cross-linked, glass-flake filled polymer that offers exceptional barrier protection and resistance to wet/dry cycling at elevated temperatures. Suitable for insulated or uninsulated pipes, stacks and equipment operating up to 450°F (232°C). Top Features Temperature resistance up to 232°C Excellent resistance to thermal shock...
A high solids corrosion resistant primer or intermediate coat on concrete, steel and (in)organic zinc primers. Top Features Excellent corrosion protection. Excellent film build and edge protection. VOC compliant to current AIM regulations.
Jotun Peroxide 11 is a specially developed additive for Jotun Chemflake Special and Jotun Chemflake CV products - refer to each product data sheet for further information. Alternatively speak to our Technical Department at Rawlins Paints for help and advice prior to purchase.
A glass-flake filled, cold cure epoxy having excellent film strength and resistance to water, salt water and wastewater exposures. Can be used on a variety of surfaces including structural steel, piping, pilings, ships, offshore structures and other equipment exposed to industrial or marine environments. Top Features High solids, low VOC...
A single package medium to high temperature coating that withstands continuous temperature up to 400ºC peaks up to 540ºC. May be applied directly to properly prepared steel. Top Features Resistant to thermal shock conditions from ambient temperature to 400ºC. Excellent weathering properties.
Jotun Jotamastic 87 Alu WG is a 'Wintergrade' version of Jotamastic 87 Alu to aid application in lower temperatures and to provide faster drying and curing times. Jotun Jotamastic 87 Alu WG is a two component polyamine cured epoxy mastic coating. It is a surface tolerant, high solids, high build product that is aluminium pigmented for improved barrier...
International Interzone 1000 is one of the most proven and reliable glass flake epoxies on the market today, with documented in-service performance dating back almost 30 years. International Interzone 1000 provides outstanding abrasion and corrosion resistance to steelwork located in the harshest offshore and inland environments.
PPG Dimetcote 9 (also known as Sigmazinc 9), is a two-component, moisture-curing zinc (ethyl) silicate coating for structural steel that can withstand substrate temperatures from –90°C (–130°F) up to 400°C (750°F), with good resistance to impact and abrasion. Anti-corrosive primer for structural steel. Specified for structural joints...
Jotun Jotamastic SF is a two component polyamine cured epoxy mastic coating that is a surface tolerant, solvent free, high build product. Well suited for early immersion and specially designed for areas where optimum surface preparation is not possible or desired. Provides long lasting protection in environments with high corrosivity.