Jotun Baltoflake Ecolife
  • Jotun Baltoflake Ecolife

Jotun Baltoflake Ecolife

0BV038SVA

Jotun Baltoflake Ecolife is a one component styrene free glass flake reinforced unsaturated polyester coating. This ultra high build, extremely abrasion resistant and fast curing barrier coating from Jotun is ideal for offshore environments, including splash zones, jetties, piles, tidal zones, decks, battery rooms, power stations, etc.

Colour
Size
Finish
£455.74
VAT excluded

£546.89 Tax incl.
Quantity

Description

Jotun Baltoflake Ecolife is a one component styrene free glass flake reinforced unsaturated polyester coating. It is an ultra high build, extremely abrasion resistant and fast curing barrier coating that can be used as primer, mid coat or finish coat in atmospheric and immersed environments. Suitable for properly prepared carbon steel, stainless steel, aluminium and approved primers. It can be applied down to +5°C surface temperature.

Jotun Baltoflake Ecolife is recommended for areas subject to extreme mechanical wear and harsh exposure conditions. Ideal for offshore environments, including splash zones, jetties, piles, tidal zones, decks, battery rooms, power stations, exterior of buried tanks, concrete bunds, refineries, bridges, mining equipment and general structural steel where future maintenance is challenging.

Approvals and Certificates

  • Pre-qualification testing in acordance with NORSOK M-501, Rev. 3/4, System 7, suitable for splash zone.

Additional certificates and approvals may be available on request.

Features & Benefits

  • Superior lifetime
  • Extreme mechanical strength
  • Fast cure and low temperature cure
  • Styrene free

Fast cure

Baltoflake Ecolife cures so fast that you can walk on it only three hours after application. Perfect for painting in tidal zones where curing time is crucial. 

Few coats
Spray up to 1500 microns in a single coat on a vertical steel surface without sagging.

Superior protection

Baltoflake Ecolife gives immense strength and protection against water, chemicals, solvents, abrasion or mechanical attack - outperforming traditional protection such as metallizing and epoxy coatings.

NORSOK pre-qualification

Baltoflake is pre-qualified in several NORSOK coating systems (System No. 1 and 7).

IMPORTANT: Jotun additives MUST be bought with this product to ensure drying and correct use. Please refer to the product Technical Data Sheet for information on which additives and how much of each are required. If in doubt, please contact our Technical Department on 0113 2455450.

Associated Additives

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
0BV038SVA

Data sheet

Application
Brush, Spray
Coverage
0.93m² per litre
Touch Dry
2 hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Carboline Thermaline 4674

A single package medium to high temperature coating that withstands continuous temperature up to 400ºC peaks up to 540ºC. May be applied directly to properly prepared steel. Top Features Resistant to thermal shock conditions from ambient temperature to 400ºC. Excellent weathering properties.

Price £70.13
In stock

Carboline Thermaline Heat Shield

An extreme performance coating for hot, cryogenic and cycling exposures. The resulting film Provides an outstanding barrier against corrosives and harsh exposures typically seen in elevated temperature environments. Top Features Unique reinforced but flexible polymer film Versatile use from cryogenic to 650°C exposures Protects steel...

Price £225.00
In stock

Jotun Jotamastic 90 GF

Jotun Jotamastic 90 GF is a two component polyamine cured epoxy mastic coating that is a surface tolerant, abrasion resistant, high solids and high build. It is reinforced with glass flakes for improved abrasion and scratch resistance. Specially designed for areas where optimum surface preparation is not possible or desired.

Price £214.11
In stock

Carboline Carbocoat 1342 Primer

A rust preventing primer. Typically used as a primer above water line on areas like superstructure, topside, deck, stores room, cargo hold etc. Top Features Quick drying, White Spirit based alkyd primer May be topcoated with alkyd paints as recommended Can be thinned

Price £229.50
In stock

Sikalastic 841 ST

Sikalastic 841 ST is a liquid applied, pure polyurea membrane. Sikalastic 841 ST is a two part, elastic, 100% solids, very fast curing pure polyurea liquid applied membrane with very good chemical resistance. Sikalastic 841 ST shall not be used in closed structures containing biogenic sulphuric acid. Sikalastic 841 ST can only be spray applied with...

Price £5,742.31
In stock

Carboline Thermo-Lag 3000-P

Thermo-Lag 3000-P is a petrochemical grade, 100% solids epoxy based intumescent designed to fireproof steelwork for up to a 4-hour fire rating, depending on the design. The recommended use for this product is fireproofing of steel beams, columns, tubes, pipes, vessel skirts, bulkheads, underdecks and electrical raceways. Top Features UL...

Price £882.30
In stock

Sherwin-Williams Macropoxy C123

Sherwin-Williams Macropoxy C123 (formerly known as Epigrip C123) is a high solids, glass flake epoxy coating for the anti-corrosive protection of blast cleaned steel. Macropoxy C123 is especially suitable for steel structures, bridges and infrastructure in aggressive atmospheric conditions. Network Rail Item 7.2.3., Highways Agency Item No. 123.

Price £69.85
In stock

Rust-Oleum Mathys Noxyde Pegarust

A rust preventing coating that is the solvent-based version of Rust-Oleum Mathys Noxyde that can be applied by brush, roller or spray in cold temperatures down to 0°C or on damp surfaces by brush, roller or spray.

Price £61.05
In stock

Tor HB Zinc Phosphate White

Tor HB Zinc Phosphate White is a quick-drying corrosion-resistant finish for machinery that provides good coverage and fast drying times, able to be overcoated after just 30 minutes. A blend of alkyd resin pigments with inorganic pigments, including zinc phosphate, and extenders and thinned essentially with Xylene to facilitate application...

Price £157.07
In stock

Carboline Polyclad 777 PL

A high performance 100% solids structural polyurethane designed to provide superior corrosion protection for steel, ductile iron and concrete pipe. Tenacious adhesion and high impact resistance allow its use in the harshest environments. Top Features Fast curing increases throughput Excellent abrasion resistance Superior wetting...

In stock

International Intercryl 525

International Intercryl 525 is designed for use as a primer/finish for structural steel, in a wide variety of general industrial environments of light to moderate corrosivity, including on bridges, commercial buildings, infrastructure and manufacturing plants. It exhibits excellent colour and gloss retention.

Price £337.45
In stock

Jotun Jotamastic 87 Alu

Jotun Jotamastic 87 Alu provides long lasting protection in environments with high corrosivity. Can be used as primer, mid coat, finish coat or as single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel and aged coating surfaces. It can be applied at sub zero surface temperatures.

Price £41.85
In stock

Coo-Var Hammercote Smooth Aerosol

Coo-Var Hammercote Smooth Aerosol is a fast drying coating which gives a hard, durable, smooth finish direct to metal objects in a handy 400ml aerosol. ADVANTAGES Very fast drying Full hardness after several days Apply direct to metal or primer Durable Gloss finish Rust resistant Heat resistant up to 150°C Interior/Exterior use

Price £7.37
In stock

Jotun Penguard Pro

Jotun Penguard Pro is a two component amine cured epoxy coating that is a surface tolerant, fast drying, high solids, high build product specially designed as a universal, all round, all year, new construction coating. This Jotun Paints product can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric and immersed...

Price £45.46
In stock

Carboline Carboguard 878

A high-build epoxy mastic coating used for atmospheric exposed and submerged steel. Top Features Excellent film build and edge protection Surface tolerant characteristics Cures at low temperature

Price £255.00
In stock

Jotun Hardtop Flexi Alu

Jotun Hardtop Flexi Alu has a remarkable ability to resist impact and will maintain initial gloss level over extended periods. Low VOCs, application of single coats up to 110 microns and fast drying add to the features of Hardtop Flexi Alu. This is one of the few products that contain anti-corrosive pigments for the best direct to metal performance.

Price £237.98
In stock