Jotun Conseal Touch-Up Alu is a one component physically drying acrylic coating with a matt finish for suitably prepared steel and coated surfaces. This version of Jotun Conseal Touch-Up is aluminium pigmented for improved barrier effect.
Jotun Conseal Touch-Up Alu is a one component physically drying acrylic coating with a matt finish for suitably prepared steel and coated surfaces. This version of Jotun Conseal Touch-Up is aluminium pigmented for improved barrier effect.
Jotun Conseal Touch-Up Alu is a high build product which is fact drying, with the product being touch dry from approximately 20 minutes at 23°C. It is ideal for use as a topcoat in atmospheric environments and can be applied at sub-zero temperatures.
Jotun Conseal Touch-Up Alu is recommended as a protective coating for refineries, power plants, bridges and buildings and it is suitable for a wide range of industrial structures.
| Technical Data | |
|---|---|
| Solids by volume | 42 ± 2 % |
| Gloss level (GU 60 °) | Matt (0-35) |
| Flash point | 25 °C |
| VOC-EU | 507 g/l |
The provided data is typical for factory produced products, subject to slight variation depending on colour.
| Recommended Film Thicknesses | Theoretical Spreading Rate | |
|---|---|---|
| Dry | Wet | |
| 75µm | 180µm | 5.6m²/l |
| 120µm | 285µm | 3.5m²/l |
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.
| Surface Preparation | ||
|---|---|---|
| Substrate | Minimum | Recommended |
| Coated Surfaces | Clean, dry and undamaged compatible coating (ISO 12944-5 6.1) | Clean, dry and undamaged compatible coating (ISO 12944-5 6.1) |
| Carbon Steel | St 2 (ISO 8501-1) | Sa 2½ (ISO 8501-1) |
| Shop Primed Steel | Clean, dry and undamaged shop primer (ISO 12944-5 6.1) | Sa 2 (ISO 8501-1) |
Please refer to the Application Guide (AG) for full details.
Application Methods:
Please refer to the Application Guide (AG) for full details.
Product Mixing:
Pot Life:
Thinner/Cleaning Solvent:
Guiding Data for Airless Spray:
| Substrate Temperature | 5°C | 10°C | 23°C | 40°C |
|---|---|---|---|---|
| Surface (touch) dry | 40 min | 30 min | 20 min | 15 min |
| Walk-on-dry | 17 h | 11 h | 10 h | 6 h |
| Dry to over coat, minimum | 3 h | 2.5 h | 2 h | 1.5 h |
| Temperature | ||
|---|---|---|
| Continuous | Peak | |
| Dry, atmospheric | 60 °C | 60 °C |
Peak temperature duration max. 1 hour
The temperatures listed relate to retention of protective properties. Aesthetic properties may suffer at these temperatures.
Note that the coating will be resistant to various immersion temperatures depending on the specific chemical and whether immersion is constant or intermittent. Heat resistance is influenced by the total coating system. If used as part of a system, ensure all coatings in the system have similar heat resistance
Depending on the actual exposure of the coating system, various primers and topcoats can be used in combination with this product. Some examples are shown below.
Previous Coat:
Subsequent coat:
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Shelf life at 23 °C
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection.
Please contact Rawlins Paints' Technical Support Team on 0113 2455450 (option 2) or send a message to [email protected] for more information.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Jotun Conseal Touch-Up Alu is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
Jotun Conseal Touch-Up is a one component physically drying acrylic coating with a matt finish. This high build product is fast drying and can be used direct to metal.Ideal as a primer/topcoat in atmospheric environments Can be applied at sub zero surface temperatures Available in hundreds of RAL, NCS, BS and Jotun Colours - 1,100+ new...
£59.33 (incl. VAT)
£49.44 (ex. VAT)
Jotun Thinner No. 7 is a paint thinner designed to improve the flow of a range of Jotun acrylic, vinyl and antifouling coatings. It can also be used as a cleaner of pumps and tools after and before painting. More Information Delivery Info
£28.09 (incl. VAT)
£23.41 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)
