Jotun Norpol Accelerator 9826 (formerly known as Jotun Accelerator DMA10) is a specially developed additive for Jotun Chemflake Special and Jotun Chemflake CV products - refer to each product data sheet for further information.
Jotun Penguard HB
Jotun Penguard HB is a two component polyamide cured high molecular weight epoxy coating designed as a high build, all purpose coating for new construction. Can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric and immersed environments.
Jotun Penguard HB is a two component polyamide cured high molecular weight epoxy coating designed as a high build, all purpose coating for new construction. Can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric and immersed environments. Suitable for properly prepared carbon steel, stainless steel, aluminium, concrete, galvanised steel, shop primed steel and thermally sprayed zinc substrates.
Jotun Penguard HB is suitable for structural steel and piping to be exposed to corrosive environments up to very high and immersed. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
- Typical Coverage (per coat)
- 5.4m² per litre
- Touch Dry
- 2.5 hours
- Brush, Spray
|Hugo on 02/09/2016|| |
Question: Hello, Do you have any application technical manual in order to better apply the coating? We are looking for a 100 microns thick. Also do you just sell the product or do you be able to apply the coating and the blasting? Thanks
For full details on application of this product please download the TDS (Technical Data Sheet), MSDS's (Material Safety Data Sheets) and Application Guide. These documents are readily available to download from the 'DATASHEETS' tab which can be found at the top of the main description section on the product page.
We are only a supplier of the coatings and do not offer an application service.
A low-temperature and rapid curing primer/finish with an extended recoat window. Provides excellent corrosion resistance as a primer, intermediate or finish on steel substrates. Top Features Low temperature cure characteristics. Rapid handling for in-shop applications. Low yellowing compared to other epoxies. VOC compliant to current...
A hammered finish maintenance paint for metal with superior metal protection, even direct to rust. Rust-Oleum CombiColor Hammertone is a primer and topcoat in one, ideal for various little projects. For a satin, matt or gloss finish, please check out Rust-Oleum CombiColor paint.
Sherwin-Williams Macropoxy C123 (formerly known as Epigrip C123) is a high solids, glass flake epoxy coating for the anti-corrosive protection of blast cleaned steel. Macropoxy C123 is especially suitable for steel structures, bridges and infrastructure in aggressive atmospheric conditions. Network Rail Item 7.2.3., Highways Agency Item No. 123.
Self-priming and suitable for application over most existing coatings, and tightly adherent rust. Serves as stand-alone system for a variety of chemical environments and is also designed for various immersion conditions. Top Features Excellent chemical resistance Surface tolerant characteristics Self-priming and primer/finish...
Sherwin-Williams Dura-Plate 301K is a solvent-free, surface and humidity tolerant two-pack modified epoxy that can be applied without dew point restrictions and over wet steel surfaces. It is an anticorrosive coating for long service life steel protection that can be used for both immersion and above the waterline service in marine, offshore, construction...
Nu-Steel Zinc Rich Primer has been specifically-formulated to prime mild steel surfaces to prepare it for overcoating with the finish of your choosing. Steel with low carbon is termed as mild steel, and such uses of this type of steel include: signs, furniture, fencing, cars and structural steel. Advantages Interior and exterior use. 3-5m²/Litre....
This epoxy is a fast-curing, heavy-duty, high-build anti-corrosive coating with a broad and versatile list of uses in marine and other corrosive environments. It is an excellent choice for the protection of ship hull exteriors, underwater and ballast tanks. Top Features Excellent immersion performance in water Suitable as a rust...
A two component, 95% solids epoxy based intumescent coating for the fire protection of structural steel. Designed to fireproof steelwork for up to a 4 hour fire rating. Top Features UL listed - for both interior and exterior environments Durable finish Thin film coating VOC compliant Easy repair
A metal primer with surface tolerant properties, can also be used as an intermediate coat, or self-priming finish over steel and zinc primers. Top Features Ready to apply after mixing Economical fit for use epoxy Used as a primer, intermediate, or finish coat VOC compliant to current AIM regulations
This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Jotacote Universal N10 as a great alternative. Jotun Jotacote Universal is a two component amine cured pure epoxy coating that is a fast drying, abrasion resistant, high solids and high build. Designed as an universal, all round,...
A water-resistant epoxy coating polymerized with a polyamine type curing agent. A high performance lining for elevated temperature and pressure immersion services in high purity water, as well as the oil/water separating processes encountered in the petroleum industry. This HAR version of Plasite 7159 is extremely abrasion resistant. Top...
Carboline Plasite 4660 provides outstanding chemical resistance, abrasion and corrosion protection to a wide variety of steel and concrete substrates in aggressive environments at elevated temperatures. This product is available as POA. Click here to email us for more information. Top Features Solvent free Excellent chemical resistance...
Jotun Jotamastic SF WG is a 'Wintergrade' version of Jotun Jotamastic SF to aid application in lower temperatures and to provide faster drying and curing times. Jotun Jotamastic SF WG is a two component polyamine cured epoxy mastic coating that is a surface tolerant, solvent free, high build product. Well suited for early immersion.
A solvent-less, high gloss, smooth epoxy coating for the lining of gas transmission pipelines. It’s hard, smooth surface aids in the flow of gas by reducing turbulence while protecting the interior surfaces from corrosion. Tested in accordance with API RP 5L2 for gas transmission pipelines. Top Features Improves flow efficiency in gas...
Sherwin-Williams Dura-Plate UHS is a fast curing solvent free epoxy lining coating which rapid return to service and high build, edge retentive properties of tank lining provides superior protection compared to conventional approaches or alternative products. Dura-Plate UHS is the user friendly solution for use in tanks containing a wide range of contents...