HMG AR141 Matt Black

TOPAR141BLK

HMG AR141 Matt Black is an air dying silicone based paint specifically formulated to enable the dried film to tolerate high temperatures up to 300ºC.

  • The full physical properties are achieved after baking at temperatures above 220ºC (at this temperature the free silicones in the system auto cross link)
  • At temperatures of up to 300ºC there is virtually no decomposition of the silicone binder.
  • Above 300ºC the silicone is gradually driven off.
  • Ease of use.
  • Quick drying.
  • Click to jump down to Technical Data
Colour
Size
Finish
£89.86
VAT excluded

£107.83 Tax incl.
Quantity

Description

HMG AR141 Matt Black is an air dying silicone based paint specifically formulated to enable the dried film to tolerate high temperatures up to 300ºC.

An outstanding feature of AR141 is that gassing and smoking are significantly reduced when it first attains high temperature.  This is of particular advantage in the automotive field, and when AR141 is use in confined spaces.



Click To Jump To Section:




Features & Benefits


  • The full physical properties are achieved after baking at temperatures above 220ºC (at this temperature the free silicones in the system auto cross link).
  • At temperatures of up to 300ºC there is virtually no decomposition of the silicone binder.
  • Above 300ºC the silicone is gradually driven off.
  • Ease of use.
  • Quick drying.



Product Specification


Technical Data
Volume Solids: 29.6%
VOC Content: 0.70kgs/ltr
SG: -
Viscosity: -
Density: 0.994 g/cm³
Storage Conditions: Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Shelf Life: 12 months from delivery date in original sealed containers.
Flash Point: 24°C



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness
Gravity Gun: 15 μm 70 μm
HVLP: 15 μm 70 μm
Brush: 15 μm 70 μm
Aerosol: 15 μm 70 μm



Coverage: 15 square metres per litre @ 15 microns dft (Theoretical).

  • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
  • These values are a guide only and are not to be used as specifications.
  • Film thickness will vary depending on actual use and specification.
  • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



Drying Times


Drying Times At 20°C
Dry To Touch: 10 minutes
Dry To Handle: 30 minutes
Dry To Recoat: 15 minutes minimum
Fully Cured: 1 hour



Surface Preparation


  • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
  • Read and follow the safety data sheet, product data sheet and label instructions
  • Stir all paints thoroughly before use
  • Always use the same batch number on the same job
  • Check colour & sheen
  • Filter the product immediately before use
  • Reduce emissions and maintain quality by replacing tin lid after use



Application Methods


Technical Data
Gravity Gun HVLP Brush Aerosol
Mixing Ratio: Base: 1 Base: 1 Ready for use Ready for use
Thinner: >10% if needed Thinner: >10% if needed - -
Thinner Options: Thinner 2621 Thinner 2621 - -
- - - -
Viscosity: 30 seconds B4 cup 30 seconds B4 cup - -
Spray Gun Setup: - - - -
Number Of Coats (Guide Only): 2 thin coats 2 thin coats 2 thin coats 2 thin coats
Flash Off: 10 minutes 10 minutes 10 minutes 10 Minutes



For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



Product Notes


Information on basic physical and chemical properties
Form: Liquid
Colour: According to product specification
Odour: Characteristic
Odour Threshold: Not determined
pH-value: Not determined
Melting point/freezing point: Undetermined
Initial boiling point and boiling range: 136°C
Flash Point: 24°C
Flammability (solid, gas): Not applicable
Ignition temperature: 432°C
Decomposition temperature: Not determined.
Auto-ignition temperature: Product is not selfigniting
Explosive properties: "Product is not explosive. However, formation of explosive air vapour mixtures are possible."
Explosion limits: Lower: 1.7 Vol %
Explosion limits: Upper: 7.0 Vol %
Vapour pressure at 20°C: 6.7 hPa
Density at 20°C: 0.994 g/cm³
Relative density: Not determined
Vapour density: Not determined
Evaporation rate: Not determined
Solubility in / Miscibility with water: NOT MISCIBLE
Partition coefficient: n-octanol/water: Not determined
Viscosity: Dynamic at 20°C: Not determined
Viscosity: Kinematic: 23 s (DIN 53211/4)
Solvent content: Organic solvents: 0.2%
Solids content: 29.6%



Health & Safety


  • Refer to the safety data sheet in the attachments section above and tin label prior to use.
  • Suitable respiratory equipment should be worn when spraying.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
TOPAR141BLK

Data sheet

Manufacturer
HMG Paints Limited
Interior/Exterior Use
Interior and exterior
Touch Dry (at 20°C)
10 Mins
Dry to Handle (at 20°C)
30 Mins
Dry to Recoat (at 20°C)
15 Mins minimum
Fully Cured (at 20°C)
1 Hour
Density
0.994 g/cm³
Solids by Volume
29.6 %
Heat Resistance (up-to)
300 °C
VOC
0.70kgs/ltr
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers.
Recommended Dry Film Thickness
15 μm
Recommended Wet Film Thickness
70 μm
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

HMG Thinner 2621

HMG Thinner 2621 is a thinner for use in various applications. For use with compatible HMG systems. Click to jump down to Technical Data

Price £9.00
In stock