Tikkurila Temal 600 is a heat resistant silicone aluminium paint which resists dry heat up to +650°C. The paint is used in cases demanding heat-resistant products such as fireplace doors, flues, exhaust pipes, sauna stoves.
Can be applied directly on steel surfaces without any primer.
For industrial use only according to Directive 1999/13/EC.
Tikkurila Temal 600 is a heat resistant silicone aluminium paint which resists dry heat up to +650°C. The paint is used in cases demanding heat-resistant products such as fireplace doors, flues, exhaust pipes, sauna stoves.
Temal 600 can be applied directly on steel surfaces without any primer.
Resists dry heat up to +650°C. The paint is used in cases demanding heat-resistant products such as fireplace doors, flues, exhaust pipes, sauna stoves.
Can be applied directly on steel surfaces without any primer. • Resistant to temperatures up to +400 ºC when applied over zinc silicate paint.
For industrial use only according to Directive 1999/13/EC.
Suitable for fireplace doors, flues, exhaust pipes, sauna stoves and other hot metal surfaces.
Store away from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials. Keep container tightly closed. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Recommended storage temperature is +5°C ...+25°C
Flash Point:
25°C (xylene)
Coverage (for a flat substrate):
14.7 m²/l
Drying Times At 23°C
DFT 15µm
10°C
23°C
35°C
Dust Dry:
30 minutes
15 minutes
10 minutes
Touch Dry:
2 hours
1 hour
30 minutes
Recoatable:
3 hours
2 hours
1 hour
Final cure and hardness will be obtained by curing at +230 ºC, 1 h
Surface Preparation
Oil, grease, salts and dirt are removed by appropriate means. (ISO 12944-4)
Steel surfaces: Blast clean to grade Sa2½. (ISO 8501-1) If blast cleaning is not possible, phosphating is recommended for cold rolled steel to improve adhesion.
Zinc silicate surfaces: Oil, grease, salt and dirt are removed from the surface by appropriate means. Repair any damage to the primer coat. Note the overcoating time of primer. (ISO 12944-4)
Application Conditions
All surfaces must be clean, dry and free from contamination.
The temperature of the ambient air, surface and paint should not fall below +10ºC during application and drying.
Relative humidity of the air should not exceed 80% during application and drying.
The surface temperature of steel should remain at least 3°C above the dew point.
Good ventilation and sufficient air movement is required in confined areas during application and drying.
Application
For conventional spraying, the product is thinned 0–10%. Recommended nozzle tip is 1.2–1.4 mm and pressure 3–4 bar.
For brush application the product should be thinned according to the circumstances.
The Volatile Organic Compounds amount of the paint mixture is 660 g/litre of paint.
VOC of the paint (thinned 10% by volume) is 680 g/l.
Health And Safety
Containers are provided with safety labels, which should be observed. Further information about hazardous influences and protection are detailed in individual health and safety data sheets.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Tikkurila Temal 600 is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...