Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Axalta Stokes Heat Resisting Silicone Aluminium Paint is a heat resistant, silicone resin based, aluminium finish for metal surfaces.
Use for metal surfaces operating up to 600°C
Good resistance to water, dilute acids, and alkalis
Excellent flexibility
Quick drying - hard dry/ready to overcoat in as little as 2 hours (at 23ºC)
Axalta Stokes Heat Resisting Silicone Aluminium Paint is a heat resistant, silicone resin based, aluminium finish, used for metal surfaces operating up to 600°C and with good resistance to water, dilute acids, and alkalis.
Good resistance to water, dilute acids, and alkalis
Excellent flexibility
Quick drying
Good coverage
Product Specification
Technical Data
Stokes Heat Resisting Silicone Aluminium Paint
Volume Solids:
9 ± 2%
Theoretical Coverage Rate:
6.0 m²/litre
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated
Dry Film Thickness:
15 µm
Wet Film Thickness:
166 µm
VOC Values:
785 + 20 g/litre
SG:
0.94 kg/lt
Flash Point:
23-60ºC
Shelf Life:
Minimum 6 months if stored as above in unopened containers
Drying Times
Curing Schedule
Applied to 15 microns DFT
+23ºC
Touch Dry
1 - 2 hours
Hard Dry/Overcoat
2 hours
Full cure
1 hour @ 200ºC
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
Surface Preparation
All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination. Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams
Performance will depend on degree of surface preparation obtained
It is recommended to blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50- 75 microns. Where blast cleaning is impractical the surface should be prepared to St2 (ISO 8501-1:2007) taking care to avoid ‘polishing’ the surface
Do not overapply or blistering may occur on heating
Brush and Roller:
Yes
For exterior use, 2 coats are recommended to a total dft of 25 microns
Do not exceed 15um dft per coat or blistering may result on heating
The coating needs to be fully cured before optimum protection is provided
The aluminium flake may cause gassing in the can – take care when removing lid
Apply at normal ambient temperatures (approx. 20°C), do not apply to surfaces at hot operating temperatures
Application Conditions
Only apply in conditions of good ventilation which must be maintained during drying and curing
Do not apply when rain, mist, sleet or snow are imminent
During application and drying time of the paint coating, the surface should be dry, the Relative Humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
Paint temperature should ideally be at a minimum of 15ºC
Health and Safety
Containers are provided with safety labels which should be observed
Further information about hazardous influences and protection are detailed in individual technical data sheet and product safety data sheets in the attachments section above.
Product Details
AR002
Data sheet
Manufacturer
Axalta Coating Systems
Interior / Exterior Use
Interior & Exterior
For Use On
Metal
Application Method
Brush, Roller, Spray
Sheen
Mid-Sheen
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
5L
Coverage
6.0 m²/litre
Recommended Thinner/Cleaner
No.7 Thinner
Min. Application Temperature
Apply at normal ambient temperatures (approx. 20°C), do not apply to surfaces at hot operating temperatures
Solids by Volume
9 ± 2%
Heat Resistance (up-to)
600°C
VOC
785 + 20 g/litre
Shelf Life (from date of manufacture)
Minimum 6 months if stored as above in unopened containers
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Axalta Stokes Heat Resisting Silicone Aluminium Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
Use Axalta Thinner General Industrial TH004 (formerly known as Axalta Thinner No. 7) to thin and clean related Axalta products, such as Plicote HB Finish. More Information Delivery Info
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...