Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to discuss your project.
Axalta Stokes Heat Resisting Matt Black Paint is a heat resistant, silicone resin based, matt black finish for interior and exterior metal at operating temperatures up of to 400°C.
When fully cured produces a durable finish which affords protection against weather, heat, water, dilute acids and alkalis
Excellent flexibility
Fast drying - Hard Dry in as little as 2 hours (at 23°C)
Axalta Stokes Heat Resisting Matt Black Paint is a heat resistant, silicone resin based, matt black finish. For use on metal surfaces operating up to 400ºC, with an occasional surge up to 500ºC. When fully cured it produces a flexible durable finish which affords protection against weather, heat, water, dilute acids and alkalis.
Approvals/Certification - Please consult Axalta Coating Systems or Rawlins Paints Technical on 0113 2455450 (option 2) or send a message to [email protected].
For use on metal surfaces operating up to 400ºC, with an occasional surge up to 500ºC
Silicone resin based, matt black finish
When fully cured produces a durable finish which affords protection against weather, heat, water, dilute acids and alkalis
Excellent flexibility
Fast Curing - touch dry in 1-2hrs @ 23ºC
Hard Dry in 2hrs at 23°C
Single Pack
Product Specification
Technical Data
Axalta Stokes Heat Resisting Matt Black Paint
Volume Solids
9 ± 2%
VOC Content
776 + 20 g/litre
SG
0.93 kg/lt
Storage Conditions
Store in dry, cool conditions and protect from frost
Shelf Life
Minimum 12 months if stored as above in unopened containers
Flash Point
23-60ºC
Film Thickness Range And Coverage
Product Data
Dry Film Thickness
Wet Film Thickness
Theoretical Coverage
Typical
15 µm
166 µm
6.0m2/litre
Practical coverage depends on the application method, painting conditions and the shape and roughness of the surface to be coated
Drying Times
Product Data
Applied to 15 microns DFT
23℃
Touch Dry
1 - 2 hr
Hard Dry/Overcoat
2 hr
Full Cure
1 hr @ 200ºC
Drying and recoating times are related to the film thickness, temperature, the relative humidity of the air and ventilation
Surface Preparation
All surfaces to be coated should be dry and cleaned as necessary to remove all oil, grease, salts, weld flux or other contamination
Where necessary, remove weld spatter and grind smooth all sharp edges and weld seams
Performance will depend on degree of surface preparation obtained
It is recommended to blast clean to Sa2½ (ISO 8501-1:2007), surface profile 50- 75 microns. Where blast cleaning is impractical the surface should be prepared to St2 (ISO 8501-1:2007) taking care to avoid ‘polishing’ the surface
Do not apply over a primer or previous coatings
Mixing
Mix thoroughly before and during use
Thinner
No.7 Thinner
Application Conditions
Only apply in conditions of good ventilation which must be maintained during drying and curing
Do not apply when rain, mist, sleet or snow are imminent
During application and drying time of the paint coating, the surface should be dry, the relative humidity should not exceed 85% and the steel temperature should remain at least 3°C above the dew point
Paint temperature should ideally be at a minimum of 15ºC
Application Methods
Application Methods
Airless Spray
Yes
Conventional Spray
Yes
Brush
Yes
Roller
Yes
Airless Spray: Do not overapply or blistering may occur on heating
Conventional spray: thin as necessary
Product Notes
For exterior use, 2 coats are recommended to a total dft of 25 microns
Do not exceed 15um dft per coat or blistering may result on heating
The coating needs to be fully cured before optimum protection is provided
Apply at normal ambient temperatures (approx. 20ºC), do not apply to surfaces at hot operating temperatures
Health & Safety
Containers are provided with safety labels which should be observed
Further information about hazardous influences and protection are detailed in individual Product Safety Data Sheets
For specific advice regarding any aspect of this product, please consult our Technical Department on 0113 2455450 (option 2) or send a message to [email protected]
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Axalta Stokes Heat Resisting Matt Black Paint is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...