Teamac High Temperature Aluminium Paint

445/Q303/5
TEA793

Teamac High Temperature Aluminium Paint. A high quality enamel for use at temperatures up to 450°C indirect heat.

Advantages

Colour
Size
Finish
£79.60(ex. VAT)
£95.51 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Teamac High Temperature Aluminium Paint. A high quality enamel for use at temperatures up to 450°C indirect heat.



Click To Jump To Section:




Features & Benefits


Advantages



Product Specification


Technical Data
Volume Solids 45%
VOC Content Max 600 g/litre
SG 1.0 @ 20°C
Viscostity 1.6 Poise @ 25°C
Flash Point 25°C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 10 to 20 µm 40 to 80 µm 12 m2/litre @ 20 microns D.F.T



The dry film only fully cures after heating, slowly, to above 220°C for 20 to 30 minutes. Unless fully cured the film remains thermoplastic and sensitive to some solvents. The film may be cured in-service, some fume and light smoke generation is assosiated with the initial cure.

The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 10 - 20 Mins
Dry To Handle: 20 Mins @ 220°C
Dry To Recoat: N/A
Fully Cured: N/A



  • Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
  • Baresteel should be free from dust, rust and scale. Blast cleaning to SA 2½ is recommended. If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
  • Any oil or grease should be removed with Teamac Universal Degreaser before de-rusting. Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts, welds etc. Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.



Mixing


Mix well before use.



Application Conditions


As dictated by normal good painting practice. In confined spaces, provide adequate ventilation during application and drying.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  No No Yes Yes



  • Thinner (Max vol): Thinners 16 (5%)
  • Nozzle Size: N/A"
  • Nozzle Pressure:N/A
  • Cleaning Solvent Thinners 16



Health & Safety


See safety data sheet - SDS 11530

Click to go back to the top of the page

Product Details
445/Q303/5/E

Data sheet

Manufacturer
Teamac
Water / Solvent Based
Solvent
For Use On
Metal
Application Method
Roller, brush
Sheen
Satin
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
2.5L
Dry to Handle (at 20°C)
20 Mins @ 220 °C
Coverage
12m² per coat
Solids by Volume
45%
VOC
Max 600 g/litre
Touch Dry
20mins
Recommended Dry Film Thickness
10 to 20 µm
Recommended Wet Film Thickness
40 to 80 µm
UN Number
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions tom rashotte on 2019-11-03 13:17:00
Question: 

will this paint prevent corrosion between the painted aluminum and unpainted stainless steel (in a wet environment)?

Answer from Rawlins’ Technical Team: 

No, but you could use the following system over aluminium;

Surface preparation: Ensure surface is clean, dry and free from metal corrosion products prior to application. Light sweep with non-metallic and chloride free abrasive (e.g. aluminium oxide or garnet) to obtain anchor profile of approximately 50 microns.

Alternatively, some sort of insulation material may also work.

questions Grayson on 2018-07-22 13:14:58
Question: 

Is this aluminium paint painted on or sprayed ?

Answer from Rawlins’ Technical Team: 

This paint should be applied by brush or roller.


Question about the product

* Required fields
(read)
Send
You might also like

General Painting Application Kit

General Painting Application Kit from Rawlins Paints provides the basics for any painting project. Whether it is a one off job, or you just want to make sure the right application tools get to site. Provides an economical way of making sure you will have what you need Ideal for interior and exterior paint projects Click to jump down to...

Price £8.02 (ex. VAT)
In Stock and Available for Delivery

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22 (ex. VAT)
In Stock and Available for Delivery