Jotun Alkydprimer
  • Jotun Alkydprimer

Jotun Alkydprimer

JOT1074
JOT1001

Jotun Alkydprimer is a one component, single pack oxidatively drying alkyd coating that can be used as primer or mid coat in atmospheric environments. Suitable for properly prepared carbon steel, aluminium and wooden substrates, this alkyd primer is ideal for a wide range of industrial structures or for touch up areas in the marine industry.

Colour
Pick a Colour
  • Current colour: Black
Close colour picker
  • White
  • Black
  • Grey
  • Red
  • Light Grey
Size
Finish
£37.71(ex. VAT)
£45.25 (inc. VAT)
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Alkyd Primer

Jotun Alkydprimer can be used as a primer or mid coat in marine and atmospheric environments. This alkyd coating is generally used for touch-up work and small scale purposes within the marine industry and will also act as a protective coating for a wide range of industrial structures - carbon steel and aluminium.

Please download the attached datasheet for more technical information, including further application specifications, drying and curing times, heat resistance and product compatibility.

  • Reduces application cost
  • Resistant to dry heat up to 120°C

When applying this alkyd primer, the surface should always be clean, dry and free-from loose materials and contamination. General surface preparation guidelines are included in the datasheet for wood, carbon steel and aluminium.

Jotun Alkyd Primer can be applied by spray, brush or roller - with rollers needing extra care to achieve the specified dry film thickness.

Jotun Thinner No. 2 should be used as the thinner and cleaning solvents for Jotun Alkydprimer.

Reduces application cost and waste
Alkydprimer requires no mixing and has no pot life restrictions, which reduce your application cost, waste and leftover paint.

Application
Can be applied to any surface of new or aged coatings in atmospheric conditions - also in conjunction with Pilot II as a topcoat or finish coat.

Product Details
JOT1074

Data sheet

Manufacturer
Jotun
Water / Solvent Based
Solvent
For Use On
Steel, Aluminium, Wood
Application Method
Spray, Airless Spray, Brush
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Product Certifications
Low Flame Spread in accordance with EU Directive for Marine Equipment,
Pack Size
5L, 20L
Coverage
10.4 - 17.3m² per litre
Touch Dry
3 hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Amit singh chandel  on 2022-12-06 13:23:13
Question: 

Can I paint this as 2nd coat primer on top of jotamastic component A RED PRIMER

Answer from Rawlins’ Technical Team: 

No this should not be used over a 2 part primer.

Jotun Jotamastic products are two part, if only component A has been applied it will not cure and must be removed.

questions Julian Brett on 2022-01-25 07:35:59
Question: 

I'm painting my boat hull, top part not antifoul, and like the look of the Jotun Pilot2 gloss. Is this suitable? What primer should I use, if it is? The boat is GRP and it will be it's first coat of paint over the original gel coat. Also, the existing antifoul is a bit flakey. I've removed all the loose paint but is it worth using a primer on this too, if there's one suitable for both the top and bottom of the hull? One pack if possible.

Answer from Rawlins’ Technical Team: 

No, for application to the existing gelcoat above the water line assuming it is clean, dry, sound and prepared as detailed in the technical data sheet we would recommend 1 coat of Jotun Penguard HB followed by 1 coat of either of the following topcoats depending on the sheen you require.

Jotun Hardtop XP or Jotun Hardtop Flexi or Jotun Hardtop AX.

For the areas below the water line, they should be cleaned with a pressure washer prior to preparation then application of 3 brush coats of Jotun Penguard HB followed by 1 roller coat of Jotun Vinyguard Silvergrey 88 then 2 brush coats of Jotun Mare Nostrum SP..

questions james lean on 2016-05-14 15:21:09
Question: I am looking for primer for aluminium below the waterline, under antifouling coat. Is this suitable? Jus to touch in on existing bare patches, not to coat a new surface.
Answer from Rawlins’ Technical Team: 

The primer we recommend for prepared aluminium (cleaned and lightly abraded), which can then be overcoated with antifouling paint is Jotun Safeguard Universal ES however this product is only available in 18L drums.

For small repair areas you could instead apply 2-3 coats of Jotun Penguard HB, followed by a single coat of Jotun Vinyguard Silvergrey 88, before applying antifouling paint.


Question about the product

* Required fields
(read)
Send
You might also like

Jotun Thinner No. 2

Jotun Thinner No. 2 is a paint thinner designed to improve the flow of a range of Jotun alkyd and oil based based products. It can also be used as cleaner of pumps and tools after and before painting. More Information Delivery Info

Price £31.27 (ex. VAT)
In Stock and Available for Delivery

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22 (ex. VAT)
In Stock and Available for Delivery