Carboline Carboguard E 19 Primer (replaces Nullifire PM021 General Purpose Epoxy Primer) is a two-component epoxy polyamide primer containing zinc phosphate. A versatile epoxy primer with excellent resistance to salts, water and alkalies, with very good resistance to mild acids and solvents.
Nullifire have made the decision in March 2023 to rebrand Nullifire PM021 General Purpose Epoxy Primer as Carboline Carboguard E 19 – please see a letter explaining the changes HERE.
Carboline Carboguard E 19 Primer is a two-component epoxy polyamide primer containing zinc phosphate. A versatile epoxy primer with excellent resistance to salts, water and alkalies, with very good resistance to mild acids and solvents.
| Technical Data | ||||||
|---|---|---|---|---|---|---|
| Carboline Carboguard E 19 Primer | ||||||
| Volume Solids: | 50 ± 2% | |||||
| Theoretical Coverage Rate: | 5,0 m²/l at 100 µm | |||||
| Allow for loss in mixing and application. | ||||||
| Dry Film Thickness: | 30 - 200 microns (1.18 - 7.87 mils) per coat | |||||
| Normally 75 µm | ||||||
| Wet Film Thickness: | 60 – 400 µm per coat, normally 150 µm | |||||
| Dry Temperature Resistance: | Continuous: 120°C (248°F) | |||||
| Non-Continuous: 150°C (302°F) | ||||||
| Primer: | Self-priming | |||||
| Topcoats: | May be topcoated with epoxy, vinyl, polyurethane or other coatings as recommended by Rawlins on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected] | |||||
| Limitations: | Not recommended for immersion service in strong acids or exposures in areas where chalking is undesirable. | |||||
| Shelf Life: | Part A: 24 months at 24°C | |||||
| Part B: 36 months at 24°C | ||||||
| Storage Temperature and Humidity: | 5°C - 45°C | |||||
| 0 - 95% relative humidity | ||||||
| Curing Schedule | ||||||
|---|---|---|---|---|---|---|
| Surface Temp. | Dry to Touch | Dry to Recoat | Final Cure | |||
| 5°C (41°F) | 4 Hours | 20 Hours | 21 Days | |||
| 15°C (59°F) | 2 Hours | 15 Hours | 14 Days | |||
| 25°C (77°F) | 1 Hour | 5 Hours | 10 Days | |||
General
Steel
Concrete
| Product Information | |||||
|---|---|---|---|---|---|
| Mixing: | Power mix separately, then combine and power mix. DO NOT MIX PARTIAL KITS. | ||||
| Thinning: | May be thinned up to 40% with Carboline Thinner 15 | ||||
| Ratio: | 2 : 1 (A to B) by volume | ||||
| Pot Life: | 6 hours at 23°C and higher at lower temperatures | ||||
| Airless Spray: | Pump Ratio: 30:1 (min) | ||||
| GPM Output: 3.0 (min) | |||||
| Material Hose: 3/8” (0.38 cm) I.D. (min) | |||||
| Tip Size: 015-.021” | |||||
| Output PSI: 2000 | |||||
| Filter Size: 60 mesh | |||||
| Brush and Roller (General): | For small areas and stripe coating. Multiple coats may be required to obtain desired appearance, and recommended dry film thickness. | ||||
| Brush: | Use a medium bristle brush | ||||
| Roller: | Use 3/8” nap solvent resistant core roller | ||||
| Product Conditions | |||||
|---|---|---|---|---|---|
| Condition | Material | Surface | Ambient | Humidity | |
| Minimum | 5°C (41°F) | 5°C (41°F) | 5°C (41°F) | 0% | |
| Maximum | 40°C (104°F) | 50°C (122°F) | 50°C (122°F) | 85% | |
Clean Up
Safety
Ventilation
Caution
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Nullifire PM021 General-Purpose Epoxy Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.
Carboline Thinner 2 is a thinner for use in industrial coatings. More Information Delivery Info
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...
