Teamac Rapidry HB Zinc Phosphate Primer
  • Teamac Rapidry HB Zinc Phosphate Primer
  • Teamac Rapidry HB Zinc Phosphate Primer
  • Teamac Rapidry HB Zinc Phosphate Primer
  • Teamac Rapidry HB Zinc Phosphate Primer

Teamac Rapidry HB Zinc Phosphate Primer

(P218)

Teamac Rapidry HB Zinc Phosphate Primer, is a high build, high performance quick drying metal primer.  It has excellent anti-corrosive properties.

    • Anti-corrosive
    • Rapid drying
    • Use on iron
    • Use on Steel
    • Semi-Matt Finish

Click to jump down to Technical Data

Colour
Size
Finish
£15.79
VAT excluded

£18.95 Tax incl.
Quantity

Description

Teamac Rapidry HB Zinc Phosphate Primer, is used as an anti-corrosive primer on iron and steel where rapid coating and finishing is required.  Ideal in coastal areas.



Click To Jump To Section:




Features & Benefits


    • Anti-corrosive
    • Rapid drying
    • Use on iron
    • Use on Steel
    • Semi-Matt Finish

Click to jump down to Technical Data



Product Specification


Technical Data
Volume Solids 45%
VOC Content Max 470 g/litre
SG 1.3 @ 20 °C
Viscostity 2.2 to 2.5 @ 25 °C
Flash Point 25 °C (closed cup)



Film Thickness Range And Coverage


Product Data
  Dry Film Thickness Wet Film Thickness Theoretical Coverage
Maximum 45 μm 100 μm 10 m2/litre @ 45 micron D.F.T.



The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.



Drying Times


Drying Times At 20°C/RH 50%
Touch Dry: 30 Mins
Dry To Handle: 6 Hours
Dry To Recoat: 4 Hours
Fully Cured: N/A



Low temperature and high humidity will adversely affect application, drying and performance of any coating.



Surface Preparation


  • Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
  • Bare steel should be free from dust, rust and scale.
  • Blast cleaning to SA 2½ is recommended.
  • If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
  • Any oil or grease should be removed with Coo-Var Universal Degreaser Cleaner before de-rusting.
  • Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts, welds etc.
  • Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.



Preceeding Coat


  • N/A



Subsequent Coat


  • Suitable topcoat, e.g Teamac Rapidry Gloss.



Mixing


  • Mix well before use.



Application Conditions


  • As dictated by normal good painting practice.
  • Care must be taken during application that the temperature is above the dew point to avoid any contamination.
  • In confined spaces, provide adequate ventilation during application and drying.



Application Methods


Method Airless Spray Conventional Spray Brush Roller
  Yes No No No



  • Thinner (Max vol): Thinners 16 (10%)
  • Nozzle size: 0.011"
  • Nozzle pressure: 1800 to 2000 psi
  • Cleaning solvent: Thinners 16



Health & Safety


For red see safety data sheet - SDS 10743, for grey see safety data sheet - SDS 10742 in the attachments section above.

Click to go back to the top of the page

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
(P218)

Data sheet

Suitable Substrates
Iron and steel
Application
Brush, Roller, Spray
Touch Dry (at 20°C)
30 Mins
Dry to Handle (at 20°C)
6 Hours
Dry to Recoat (at 20°C)
4 Hours
Fully Cured (at 20°C)
N/A
Coverage
10m² per litre
Recommended Thinner/Cleaner
Teamac Thinner 16
Solids by Volume
45%
VOC
Max 470 g/litre
Touch Dry
45 Mins
Finish
Semi-Matt
Size
1 litre, 2.5 litre, 5 litre, 20 litre
Recommended Dry Film Thickness
45 μm
Recommended Wet Film Thickness
100 μm
UN Number
1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


questions Phil Ambrose on 2016-01-20 23:05:30
Question: 

What can be used to thin and clean up Teamac Rapidry HB Zinc Phosphate Primer (P218)?


Question about the product

* Required fields
(read)
Send
You might also like

Teamac Thinner 16

A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application. Suitable for application by Brush, Roller or Spray.  Teamac Thinner 16 can also be used for the cleaning of some surfaces prior to application of the coating. Suitable for cleaning of the...

Price £11.59
In stock

Coo-Var Universal Degreaser Cleaner

Coo-Var Universal Degreaser Cleaner is a careful blend of solvents to give powerful cleaning and degreasing properties.  Product Features Degreases and removes oil patches from floors, walls, interior and exterior surfaces prior to acid etching or painting. Part of the cleaning process. Essential for a good finish. Can also be used as a...

Price £19.02
In stock