Alternatively you can email our sales & support team on [email protected]
Teamac Red Oxide Primer
440/F158/65/D
Teamac Red Oxide Primer, is an inexpensive primer based upon iron oxide for use on structural steelwork, iron and metalwork which can be left as a short term finish or overcoated with Teamac Marine or Industrial coatings.
Traditional general purpose primer for iron and steel
Provides flat finish for topcoats to adhere to
Perfect for steel & cast iron
Suitable for narrowboats, cruisers, barges and marine structures
Teamac Acrylic Coating, is an inexpensive primer based upon iron oxide for use on structural steelwork, iron and metalwork which can be left as a short term finish or overcoated with Teamac Marine or Industrial coatings.
Suitable for narrowboats, cruisers, barges and marine structures. It can be applied to suitably prepared steel and cast iron. Where there is heavy oxidation that cannot be removed it can be used over Teamac Rust Converter.
The practical spreading rate may be lower as this depends on factors such as the porosity and roughness of the surface to be painted and material losses during application.
Drying Times
Drying Times At 20°C/RH 50%
Touch Dry:
2 Hours
Dry To Handle:
12 Hours
Dry To Recoat:
12 hours or overnight
Fully Cured:
5 - 7 Days
Low temperature and high humidity will adversely affect application, drying and performance of any coating.
Surface Preparation
Ensure all surfaces are clean, dry and free from grease, oil and any other contaminates.
Bare steel should be free from dust, rust and scale.
Blast cleaning to SA 2½ is recommended.
If blast cleaning is impractical, mechanical cleaning should be employed as hand cleaning does not clean the steel to the required degree.
Any oil or grease should be removed with CooVar Degreaser before de-rusting.
Where blast cleaning is carried out after assembly, special attention must be paid to edges, corners, nuts, bolts, welds etc.
Welds should, if necessary be ground and all weld spatter, slag etc. must be removed.
Preceeding Coat
N/A
Mixing
Mix well before use.
Application Conditions
As dictated by normal good painting practice.
Care must be taken during application that the temperature is above the dew point to avoid any contamination.
In confined spaces, provide adequate ventilation during application and drying.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Product Details
440/F158/65/D
Data sheet
Manufacturer
Teamac
Suitable Substrates
Steel & Cast Iron
Key Features
Traditional general purpose primer for iron and steel. Provides flat finish for topcoats to adhere to.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
A specially formulated blend of solvents designed to mix with its compatible Teamac or Coo-Var coating to create an optimal consistancy for application.
Suitable for use with Brush, Roller or Spray.
Teamac Thinner 14 can also be used for the cleaning of some surfaces prior to application of the coating.
Also suitable for the cleaning of...
Coo-Var Universal Degreaser Cleaner is a careful blend of solvents to give powerful cleaning and degreasing properties.
Product Features
Degreases and removes oil patches from floors, walls, interior and exterior surfaces prior to acid etching or painting.
Part of the cleaning process.
Essential for a good finish.
Can also be used as a...
International Intergard 400 is a high build, two component epoxy, pigmented with lamellar micaceous iron oxide for enhanced corrosion resistance and improved overcoating properties after ageing.
This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Penguard Express ZP or Jotun Penguard HSP ZP as great alternatives.
Jotun Penguard Special is a two component polyamide cured high molecular weight epoxy coating. It is a zinc phosphate pigmented, high build product specially...
PPG SigmaWeld 199 is a two-component, moisture-curing low zinc (ethyl) silicate prefabrication primer that is suitable for automatic application on shot blasted steel plates. Good cutting and excellent welding properties, including MIG/MAG welding in various positions (either automatic or manual welding), fast-drying and low fume release are...
A high solids corrosion resistant primer or intermediate coat over steel and inorganic zinc primers.
Top Features
Excellent corrosion protection
Good abrasion resistance
Cures down to 40°F
Part of the high performance, immersion grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures.
Top Features
Temperature resistant up to 204ºC
Protects steel substrates
Very good flexibility
Excellent overall chemical resistance
Very good abrasion resistance
HMG Synthetic BDX Primer is a high build, anti-corrosive, 1K alkyd primer for use under all HMG Synthetic topcoats.
High build and excellent sandability after a short drying period.
Excellent application and scratch filling properties.
Available in white, light grey, dark grey and red oxide.
Click to jump down to Technical Data
International Intercure 420 is a two component, high solids, low VOC epoxy micaceous iron oxide coating formulated on proprietary polymer technology which provides rapid cure and overcoating even under low temperature conditions.
International Interzinc 52 is a two component, metallic zinc rich epoxy primer which complies with the composition and performance requirements of SSPC Paint 20. It has been designed to provide excellent corrosion resistance in both maintenance and new construction situations.
Tor Adheron Metal Primer, a general purpose quick-drying anti-corrosive primer/finish for steel that can be applied by brush, roller or spray. Designed to give a tough but flexible primer/finish, the primer can be overcoated with conventional alkyd and chlorinated rubber finishes after just 4 hours. Additional coats of Tor Adheron Metal Primer...
This epoxy is a fast-curing, heavy-duty, high-build anti-corrosive coating with a broad and versatile list of uses in marine and other corrosive environments. It is an excellent choice for the protection of ship hull exteriors, underwater and ballast tanks.
Top Features
Excellent immersion performance in water
Suitable as a rust...
Jotun Resist 86 is a two component moisture cured inorganic zinc ethyl silicate coating that is a fast curing, very high zinc dust containing product.
Specially designed by Jotun as a primer in coating systems where extended durability is required. It provides a solid foundation for the optimal performing coating system in the toughest...
PPG Sigma Vikote 63 is a high-build bituminous protective coating for steel, concrete and fibre cement. Offering good resistance to sea and fresh water, PPG Sigma Vikote 63 can be used to protect void spaces, cofferdams, steelwork behind lining and pipes.
Top Features
Good adhesion to steel and galvanised steel
Flat finish
Black in...
A high performance epoxy that has excellent resistance to fresh and salt water exposures. This coating exhibits outstanding moisture and surface tolerance during application, low temperature cure capability, and very fast cure response for quick return to service.
Top Features
High solids, low VOC
Excellent wetting properties
Excellent...
Coo-Var Rust Converter will resist the rusting process and allow the surface to be overcoated. This product will turn any rust on the substrate into a stable surface allowing the user to then be able to coat the substrate without the risk of any further corrosion.
Product Features
Low Sheen finish
Suitable Surfaces: Metal
Application:...
PPG SigmaShield 420 is a two-component, reinforced high solids polyamine adduct cured epoxy coating, ideal as a coating for cargo tanks of bulk or oil carriers and storage tanks.
Buildcoat for underwater and boottop systems - No induction time
Excellent abrasion and impact resistance, with outstanding water resistance, including seawater...
PPG SigmaZinc 160 is a two-component, moisture-curing inorganic zinc (ethyl) silicate anti-corrosive primer for structural steel. This low-temperature curing coating is suitable as a system primer in various paint systems based on unsaponifiable binders.
Top Features
Galvanic action eliminates sub-film corrosion
Can withstand substrate...