International Intergard 214
  • International Intergard 214

International Intergard 214

EGA260

International Intergard 214 is a two component epoxy sealer coat pigmented with aluminium flake for the effective penetration and sealing of thermally sprayed aluminium coatings to eliminate porosity. Has specification approval for UK Department of Transport Item No.159.

Colour
Size
£65.36
VAT excluded

£78.43 Tax incl.
Quantity

Description

International Intergard 214 is a two component epoxy sealer coat pigmented with aluminium flake for the effective penetration and sealing of thermally sprayed aluminium coatings to eliminate porosity.

International Intergard 214 has the following specification approvals:

  • UK Department of Transport Item No.159

International Intergard 214 can be overcoated with a wide range of products, including:

International Intergard 214 is designed to seal porosity in aluminium metal spray. When applying by brush, work the sealer thoroughly into the surface of the aluminium metal spray.

When application is by spray rather than by brush, careful inspection will be needed to ensure thorough sealing of the aluminium metal spray. Any runs, sags or pooling on horizontal surfaces should be brushed out immediately.

Best results will be achieved at temperatures above 0°C (32°F). Surface temperature must always be a minimum of 3°C (5°F) above dew point. In common with all epoxies, Intergard 214 will chalk when exposed to weathering but this will not reduce efficiency in sealing metal spray.

Level of sheen and surface finish are dependent on application method. Avoid using a mixture of application methods whenever possible. Intergard 214 is not suitable for exposure to acid or alkaline environments.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
EGA260

Data sheet

Application
Brush, Roller, Spray
Coverage
12m² per litre
Touch Dry
20 mins
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Carboline Carbocrylic 3358 IMC

Used as an intermediate coat on steel or concrete in a three coat system, and can be topcoated with several generic types of topcoats. Excellent abrasion resistance and flexibility with good chemical resistance. Top Features Single component Fast drying Low VOC

Price £70.28
In stock

PPG AquaCover 20

PPG AquaCover 20 (also known as Sigma Aquacover 20) is a one-component waterborne, high-build zinc phosphate primer/coating, based on acrylic dispersion. It can be overcoated with most waterborne acrylics, solvent-borne epoxy coatings and alkyd paints, as well as certain solvent-borne, two-component products. Useful for when solvents are...

Price £64.35
In stock

Teamac Zinc Phosphate Primer

An anticorrosive primer on iron and steel, for use with a range of conventional topcoats such as Teamac Marine Gloss and Teamac Metalcote Plant Enamel.

Price £14.12
In stock

PPG AquaWeld 100

PPG AquaWeld 100 (also known as Sigma AquaWeld 100) is a two-component, moisture-curing, waterborne low zinc (ethyl) silicate prefabrication primer that is suitable for automatic application on shot-blasted steel plates. Top Features Certified by Lloyds Register and SLV Low fume release during welding and cutting Provides regular, smooth...

Price £496.80
In stock

International Interzinc 22

International Interzinc 22 is a two component, rapid recoat, inorganic zinc rich ethyl silicate primer and is part of the Interzinc 22 Series of products that deliver consistently fast re-coating across a choice of 85%, 80%, 77% or 65% minimum zinc content products. The variable zinc levels allow you to tailor your choice of product to meet...

Price £433.05
In stock

Jotun Penguard HSP ZP

Jotun Penguard HSP ZP is a two component polyamide cured epoxy coating that is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. To be used as a primer in atmospheric environments and is suitable for properly prepared...

Price £101.44
In stock

PPG Dimetcote 9

PPG Dimetcote 9 (also known as Sigmazinc 9), is a two-component, moisture-curing zinc (ethyl) silicate coating for structural steel that can withstand substrate temperatures from –90°C (–130°F) up to 400°C (750°F), with good resistance to impact and abrasion. Anti-corrosive primer for structural steel. Specified for structural joints...

Price £270.50
In stock

International Interzinc 72

International Interzinc 72 is a two component, metallic zinc rich epoxy primer, designed to provide excellent corrosion resistance both as a single coat and as a primer for a high performance coating system. Contains 90% zinc by weight in the dry film.

Price £338.07
In stock

Sherwin-Williams Zinc Clad II EU

Sherwin-Williams Zinc Clad II EU is a self-curing solvent based, two component zinc silicate coating for the protection of blast cleaned steel surfaces. It is capable of withstanding temperatures up to 400°C and of curing at temperatures down to 0°C. 

Price £110.26
In stock

Nullifire PM015 Aluminium Epoxy Primer

Nullifire PM015 Aluminium Epoxy Primer is a high-build, low temperature curing modified aluminium epoxy mastic. Nullifire PM015 provides unequaled levels or barrier protection and corrosion resistance over existing finishes and rusted or St2/St3 cleaned steel.

Price £89.40
In stock

Sherwin-Williams Macropoxy M902

Sherwin-Williams Macropoxy M902 (formerly known as Epigrip M902) is a low temperature curing hi-build 2-pack epoxy brushing aluminium primer coating capable of curing down to 0°C. 

Price £48.33
In stock

SikaCor 6630 Primer

SikaCor 6630 Primer is part of the SikaCor 6630 System which is a low-solvent, oxidative drying high-build coating with active corrosion protection pigments based on modified synthetic resin combination. SikaCor 6630 Primer is mainly used in case of manual de-rusting preparation or maintenance is being carried out on existing systems.

Price £203.39
In stock

Carboline Carbocrylic 3359 DTM

A durable and high performance acrylic coating for use where excellent weathering properties and chemical resistance are required. Use as a direct-to-metal acrylic coating for structural steel, as well as other exterior and interior uses. Top Features Smooth, attractive, high build finish Excellent corrosion protection Meets most VOC...

Price £92.81
In stock