Sherwin-Williams Epigrip C267V3
  • Sherwin-Williams Epigrip C267V3

Macropoxy 267

267

Macropoxy 267 (formerly known as Sherwin-Williams Macropoxy C267V3 and as Epigrip C267V3) is a high solids 2-pack epoxy, pigmented with micaceous iron oxide. It is used as an undercoat in conjunction with high performance primers. Macropoxy 267 has excellent resistance to moisture, aliphatic solvents, abrasion, alkali spillage, weather and petroleum solvents.

Colour
Size
£57.48
VAT excluded

£68.98 Tax incl.
Quantity

Description

Macropoxy 267 (formerly known as Sherwin-Williams Macropoxy C267V3 and as Epigrip C267V3) is a high solids 2-pack epoxy, pigmented with micaceous iron oxide, used as an intermediate in conjunction with high performance primers.



Recommended Primers/Topcoats


Compatable with a wide range of Macropoxy, Zinc Clad Epoxy primers and buildcoats.

Recommended Thinner: Cleanser/Thinner No 5 (for thinning), Cleanser/Thinner No 9 or No13 (for cleaning)

Endorsements


  • HA Item No 112



Surface Preparation


Ensure surfaces to be coated are clean, dry and free from all surface contamination.



Application Equipment


Suitable for applying by brush and roller. Application of more than one coat may be necessary to give equivalent dry film thickness to a single spray applied coat.

Airless Spray

  • Nozzle Size : 0.46mm (15-19 thou)
  • Fan Angle : 40°
  • Operating Pressure : 155kg/cm² (2200 psi)

The airless spray details given above are intended as a guide only. Details such as fluid hose length and diameter, paint temperature and job shape and size all have an effect on the spray tip and operating pressure chosen. However, the operating pressure should be the lowest possible consistent with satisfactory atomisation. As conditions will vary from job to job, it is the applicators’ responsibility to ensure that the equipment in use has been set up to give the best results. If in doubt our technical team should be consulted.

Conventional Spray

  • Nozzle Size: 1.27mm (50 thou)
  • Atomising Pressure: 3.5kg/cm² (50 psi)
  • Fluid Pressure: 0.7kg/cm² (10 psi)

The details of atomising pressure, fl uid pressure and nozzle size are given as a guide. It may be found that slight variations of pressure will provide optimum atomisation in some circumstances according to the set up in use. Atomising air pressure depends on the air cap in use and the fl uid pressure depends on the length of line and direction of feed i.e. horizontal or vertical.

For application by conventional spray, it may be necessary to thin the paint by the addition of up to 10% Cleanser Thinner No. 5.

Where thinning has been carried out the wet fi lm thickness must be adjusted accordingly. N.B. Thinning will affect VOC compliance.



Application Conditions & Overcoating


Epoxy paints should preferably be applied at temperatures in excess of 10ºC. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3ºC above the dew point and always above 0°C.

At application temperatures below 10°C, drying and curing times will be signifi cantly extended, and spraying characteristics may be impaired.

Application at ambient air temperatures below 5°C is not recommended.

In order to achieve optimum water and chemical resistance, temperature needs to be maintained above 10ºC during curing. If it is desired to overcoat outside the times stated on the data sheet, please seek advice of our technical team.



Additional Notes


Drying times, curing times and pot life should be considered as a guide only.

The curing reaction of epoxies commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature. Refer to the Product Data Sheet for details on tropical use.



Typical Thickness, Coverage and Application Rates


Refer to the Product Data Sheet for more information and recommendations, or contact our technical team on 0113 2455450.



Average Drying Times


15°C 23°C 35°C
To touch: 1¼ hours 45 minutes 30 minutes
To recoat: 6 hours 4 hours 2 hours
To handle: 10 hours 6 hours 3 hours

These figures are given as a guide only. Factors such as air movement and humidity must also be considered.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
267

Data sheet

Typical Coverage (per coat)
6.24m² per litre
Touch Dry
30 mins
Application
Brush, Roller, Spray
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Carboline Thermaline 400 EU Primer

Part of the high performance, immersion grade coating system which has excellent resistance to wet/dry cycling conditions at elevated temperatures.  Top Features Temperature resistant up to 204ºC protects steel substrates Very good flexibility Excellent overall chemical resistance Very good abrasion resistance

Price £164.25
In stock

Jotun Penguard Special B10

Jotun Penguard Special B10 is a two component polyamide cured high molecular weight epoxy coating that contains 65% zinc phosphate pigments by weight. Specially designed as a primer for galvanised steel it can be used as a primer as part of a complete system in atmospheric environments. 

Price £146.02
In stock

Carboline Carbocoat 115

A fast-drying steel primer that provides corrosion protection on structural steel. Well suited for fabrication shops that need fast cure to dry and handle times. Top Features Rapid cure and fast-drying VOC compliant for most areas Good for filling properties on rough and pitted steel

Price £42.75
In stock

Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion

Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion is a high quality anti-rust primer for Rust-Oleum CombiColor. The Anti-Corrosion Primer will ensure an even longer anti-rust protection on new or rusted steel surfaces and provides and enhances protection against corrosion.

Price £7.19
In stock

International Intercure 384

International Intercure 384 is a two component, high solids, low VOC epoxy micaceous iron oxide intermediate coating offering excellent barrier protection, low temperature cure and rapid overcoating properties. Pigmented with micaceous iron oxide to comply with the requirements of BS5493:1977

Price £85.76
In stock

Rust-Oleum 6400 Fast Drying Shopprimer

A fast drying, solvent based, anti-corrosive primer for temporary metal protection intended as the first coat in shop coating applications and provides the required basic protection following metal fabrication and assembly operations.

Price £22.38
In stock

Jotun Penguard Express MIO

Jotun Penguard Express MIO is a two component amine cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in...

Price £42.82
In stock

Jotun Barrier Plus

This Jotun Paints product is a high solids, very high zinc dust content primer for highly corrosive environments and can be applied down to 0°C surface temperature. Jotun Barrier Plus is a two component polyamine cured zinc rich epoxy coating.

Price £146.04
In stock

Jotun Muki Z 2001

An all-round excellent choice for the temporary protection of steel exposed to highly corrosive environments. Muki Z 2001 from Jotun has a solid track record and a reputation built on satisfied customers in a range of industries and countries worldwide. Jotun Muki Z 2001 is a two component inorganic low zinc moisture curing zinc ethyl silicate coating...

Price £119.64
In stock

Rust-Oleum 3302 CombiPrimer Adhesion

A primer from Rust-Oleum to make difficult smooth surfaces coatable. CombiPrimer Adhesion is ideal for use on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces that normal paints cannot stick to.

Price £7.19
In stock

Sherwin-Williams Macropoxy M182

Sherwin-Williams Macropoxy M182 (formerly known as Resistex M182) is a single pack epoxy anti-corrosive primer, used as an oil resisting primer for application onto ferrous substrates.

Price £161.94
In stock

Sherwin-Williams Mordant Wash L703

Sherwin-Williams Mordant Wash L703 (formerly known as Leighs L703/Transgard TG155) is a blue mordant solution for application onto galvanized surfaces as a chemical pre-treatment to improve the adhesion of subsequent paint systems.

Price £37.12
In stock

Sherwin-Williams Macropoxy M902

Sherwin-Williams Macropoxy M902 (formerly known as Epigrip M902) is a low temperature curing hi-build 2-pack epoxy brushing aluminium primer coating capable of curing down to 0°C. 

Price £48.33
In stock

International Intergard 307

International Intergard 307 is a two pack epoxy zinc phosphate primer, primarily formulated to meet the requirements of the UK Highways Agency specification. International Intergard 307 is intended to be used as a primer or blast primer under high build epoxy coating schemes for new construction.

Price £61.79
In stock

PPG Dimetcote 9

PPG Dimetcote 9, an anticorrosive primer for structural steel that can withstand substrate temperatures from –90°C (–130°F) up to 400°C (750°F), with good resistance to impact and abrasion. 2 component anti-corrosion primer Moisture-curing zinc (ethyl) silicate coating for structural steel Withstands substrate temperatures from –90°C...

Price £270.50
In stock

SikaCor 6630 Primer

SikaCor 6630 Primer is part of the SikaCor 6630 System which is a low-solvent, oxidative drying high-build coating with active corrosion protection pigments based on modified synthetic resin combination. SikaCor 6630 Primer is mainly used in case of manual de-rusting preparation or maintenance is being carried out on existing systems.

Price £203.39
In stock