Sherwin-Williams Epigrip C425V2
  • Sherwin-Williams Epigrip C425V2

Sherwin-Williams Macropoxy C425V2

C425V2

Sherwin-Williams Macropoxy C425V2 (formerly Epigrip C425V2) is a high build 2-pack epoxy zinc phosphate primer/buildcoat to provide anti-corrosive protection of carbon steel surfaces prepared by abrasive blast cleaning. Network Rail and NORSOK approved, ideal for use in internal/external exposed conditions including offshore, petrochemical and sub-sea environments.

Colour
Size
Finish
£71.21
VAT excluded

£85.45 Tax incl.
Quantity

Description

Sherwin-Williams Macropoxy C425V2 (formerly known as Epigrip C425V2) is a high build 2-pack epoxy zinc phosphate primer/buildcoat to provide anti-corrosive protection of carbon steel surfaces prepared by abrasive blast cleaning.

Sherwin-Williams Macropoxy C425V2 can be spray applied at thicknesses between 100 and 250 microns dry to provide both primer and buildcoat in a single coat.

A top coat is only required for decorative purposes. Without topcoat, Sherwin-Williams Epigrip C425V2 will quickly discolour and patchiness may be exaggerated due to film thickness variation, but will nonetheless provide excellent anti-corrosive protection as a single coat protective epoxy nor will intercoat adhesion be affected by any discolouration.

Sherwin-Williams Macopoxy C425V2 is for use in internal/external exposed conditions including offshore, petrochemical and sub-sea environments.

Endorsements

  • Network Rail – Item No 7.1.4
  • Complies with BS5493:1977 - Table 4K Type KP1A.
  • Approved for use by MoD(N) as a gel coat over FRP/GRP surfaces
  • Complies with NORSOK M501 Rev. 5 System 1 and 7.

Recommended Topcoats

Indefinitely overcoatable with epoxy systems provided the surfaces to be coated have been suitably cleaned. Where a high degree of gloss and colour retention is required, overcoat with Acrolon C137V2, Acrolon C237, Acrolon 1850 and Acrolon 7300 within 7 days at a minimum dft of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.

For overcoating outside the above parameters and with alkyd systems, consult our Technical team.

Application Conditions & Overcoating

Epoxy paints should preferably be applied at temperatures in excess of 10ºC. Relative humidity should not exceed 90% and in these conditions good ventilation is essential. Substrate temperature shall be at least 3ºC above the dew point and always above 0°C.
At application temperatures below 10°C, drying and curing times will be signifi cantly extended, and spraying characteristics may be impaired. Application at ambient air temperatures below 5°C is not recommended.

In order to achieve optimum water and chemical resistance, temperature needs to be maintained above 10ºC during curing.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
C425V2

Data sheet

Application
Brush, Roller, Spray
Touch Dry
1.5 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

International Interzinc 52

International Interzinc 52 is a two component, metallic zinc rich epoxy primer which complies with the composition and performance requirements of SSPC Paint 20. It has been designed to provide excellent corrosion resistance in both maintenance and new construction situations.

Price £340.89
In stock

Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion

Rust-Oleum 3369/3380 CombiPrimer Anti-Corrosion is a high quality anti-rust primer for Rust-Oleum CombiColor. The Anti-Corrosion Primer will ensure an even longer anti-rust protection on new or rusted steel surfaces and provides and enhances protection against corrosion.

Price £7.19
In stock

Jotun Penguard HSP MIO

Jotun Penguard HSP MIO is a two component polyamide cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Can be used as a primer or a mid coat in atmospheric environments. Specially designed for new construction where fast dry to handle and over coating times are required. 

Price £102.14
In stock

1803 HB Epoxy Intermediate/Finish

A high solids, epoxy intermediate/finish coat, providing exceptionally high film builds (up to 200 microns DFT per coat), enabling maximum performance in a minimum number of coats. Can be used year round due to its ability to cure down to temperatures as low as 2°C.

Price £91.82
In stock

Bradite Surface Tolerant Primer

A high performance two pack epoxy solvent based surface tolerant anti-corrosive primer, specifically developed for ferrous metals which are lightly rusted. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Contains a high level of zinc phosphate anti-corrosive pigment Flexible and abrasion resistant...

Price £68.89
In stock

Carboline Phenoline 311 Primer

A tank lining holding primer that has a variety of attributes including low-temperature cure, fast recoat times, moisture tolerance during application and cure, and excellent blast-hold protection. Phenoline 311 Primer is often used with thick film lining systems as a holding primer (maintain blast cleaning) and is suitable for both new tanks...

Price £258.83
In stock

Jotun Muki Z 3000

This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Muki Z 2001 as a great alternative. Offers excellent corrosion protection of steel during normal storage and fabrication, and reduces exposure to fumes during welding and cutting compared with high zinc shop primers. Especially...

Price £138.72
In stock

Jotun Muki EPS

A fast drying, shop primer designed for high welding and cutting speed, giving reduced weld porosity and back burning or as a temporary primer in a new construction phases or as a primer in a complete coating system.

Price £95.45
In stock

SikaCor EG 1

SikaCor EG 1 is a two-pack, high-solids, epoxy-based intermediate coat containing micaceous iron oxide. The coating is designed as a mechanically resistant intermediate coat on steel surfaces exposed to atmospheric conditions, hot-dip galvanized steel, zinc-spray, stainless steel and aluminium.

Price £70.52
In stock

Jotun Muki Z 2001

An all-round excellent choice for the temporary protection of steel exposed to highly corrosive environments. Muki Z 2001 from Jotun has a solid track record and a reputation built on satisfied customers in a range of industries and countries worldwide. Jotun Muki Z 2001 is a two component inorganic low zinc moisture curing zinc ethyl...

Price £119.64
In stock

Rust-Oleum 1060/1080 High Build Metal Primer

Rust-Oleum 1060/1080 High Build Metal Primer is for extra protection of bare or blasted metal, offers maximum durability under severely corrosive conditions. It assures appropriate protection under light industrial exposure conditions, if applied on a Rust-Oleum metal primer followed by Rust-Oleum 7500 Alkythane.

Price £86.96
In stock

PPG SigmaWeld 199

PPG SigmaWeld 199 is a two-component, moisture-curing low zinc (ethyl) silicate prefabrication primer that is suitable for automatic application on shot blasted steel plates. Good cutting and excellent welding properties, including MIG/MAG welding in various positions (either automatic or manual welding), fast-drying and low fume release are...

Price £216.72
In stock

Nullifire PM018 Primer or Top Seal Epoxy Coating

Nullifire PM018 Primer or Top Seal Epoxy Coating is a two-components modified epoxy coating. It is a heavy duty, high build coating for protection of steel in corrosive environments and is excellent for use at low temperatures. 

Price £311.85
In stock

PPG SigmaShield 420

PPG SigmaShield 420 is a two-component, reinforced high solids polyamine adduct cured epoxy coating, ideal as a coating for cargo tanks of bulk or oil carriers and storage tanks. Buildcoat for underwater and boottop systems - No induction time Excellent abrasion and impact resistance, with outstanding water resistance, including seawater...

Price £375.20
In stock

International Intergard 251

International Intergard 251 is a two component epoxy anti-corrosive primer pigmented with zinc phosphate for use on properly prepared surfaces in both new construction situations and as an industrial maintenance primer for a wide range of anti-corrosive coatings systems.

Price £237.33
In stock