Sherwin-Williams Macropoxy K267
  • Sherwin-Williams Macropoxy K267

Sherwin-Williams Macropoxy K267

K267

Sherwin-Williams Macropoxy K267 (formerly known as Epigrip K267/Transgard TG121) is a two-pack, pigmented with micaceous iron oxide, designed as an intermediate coat in conjuction with Macropoxy high performance primers. 

Colour
Size
£79.59
VAT excluded

£95.51 Tax incl.
Quantity

Description

Sherwin-Williams Macropoxy K267 (formerly known as Epigrip K267/Transgard TG121) is a two-pack, pigmented with micaceous iron oxide, designed as an intermediate coat in conjuction with Macropoxy high performance primers. 

Endorsements

  • BS476 Part 7 - Surface Spread of Flame - for details of substrates/scheme, consult our technical team.
  • Highways Agency Item No. 121
  • Network Rail Item No. 7.2.2 

Recommended Primers/Topcoats

Compatible with a wide range of Macropoxy, Dura-plate, Zinc Clad Epoxy Primers and Buildcoats.

Indefinitely overcoatable with epoxy systems provided the surfaces to be coated have been suitably cleaned. Where a high degree of gloss and colour retention is required overcoating with Acrolon C137V2, Acrolon C237, Acrolon 1850 and Acrolon 7300 within 7 days at a minimum dft of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.

Application Conditions & Overcoating

This material should preferably be applied at temperatures in excess of 10oC. In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3oC above the dew point and always above 0°C. 

At application temperatures below 10°C, drying and curing times will be significantly extended, and spraying characteristics may be impaired.

Application at ambient air temperatures below 5°C is not recommended.

In order to achieve optimum water and chemical resistance, temperature needs to be maintained above 10oC during curing.

Additional Notes

Drying times, curing times and pot life should be considered as a guide only.

The curing reaction of epoxies commences immediately the two components are mixed, and since the reaction is dependent on temperature, the curing time and pot life will be approximately halved by a 10°C increase in temperature and doubled by a 10°C decrease in temperature.

Epoxy Coatings - Tropical Use

Epoxy paints at the time of mixing should not exceed a temperature of 35oC. Use of these products outside of the pot life may result in inferior adhesion properties even if the materials appear fit for application. Thinning the mixed product will not alleviate this problem.

The maximum air and substrate temperature for application is 50oC providing conditions allow satisfactory application and film formation. If the air and substrate temperatures exceed 50oC and epoxy coatings are applied under these conditions, paint film defects such as dry spray, bubbling and pinholing etc, can occur within the coating.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
K267

Data sheet

Typical Coverage (per coat)
6.6m² per litre
Touch Dry
2 Hours
Application
Brush, Roller, Spray
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Nullifire PM019 Primer for Blasted Steel Substrates

Nullifire PM019 Primer for Blasted Steel Substrates is an anti-corrosive transport primer for temporary protection of blasted steel substrates, which will be finished with a compatible basecoat. Applied at standard film thickness, the protection in outdoor conditions is limited to approximately 3 months. Within this period of time the finishing coating...

Price £313.56
In stock

Sherwin-Williams FIRETEX C69

Sherwin-Williams FIRETEX C69 is a two pack epoxy, fast-track blast primer for intumescent coatings. Sherwin-Williams FIRETEX C69 is a fast-track temporary protective coating for surfaces prepared by abrasive blast cleaning, designed for use under FIRETEX intumescent coatings.

Price £151.77
In stock

Macropoxy 267

Macropoxy 267 (formerly known as Sherwin-Williams Macropoxy C267V3 and as Epigrip C267V3) is a high solids 2-pack epoxy, pigmented with micaceous iron oxide. It is used as an undercoat in conjunction with high performance primers. Macropoxy 267 has excellent resistance to moisture, aliphatic solvents, abrasion, alkali spillage, weather and...

Price £57.48
In stock

Jotun Penguard Midcoat MIO

Jotun Penguard Midcoat MIO is a two component polyamide cured epoxy coating that is a micaceous iron oxide (MIO) pigmented, high solids, high build product. Designed as a mid coat in systems for new construction in atmospheric environments. Suitable in approved coating systems.

Price £141.80
In stock

407 Multi Surface Primer

This low odour, high opacity white primer/sealer is suitable for most surfaces including tiles, wood, metal (including galvanised), plaster, existing paint, masonry and most plasics (test a small area first).

Price £23.39
In stock

Cromadex 750 Two Pack Epoxy Primer

Cromadex 750 Two Pack Epoxy Primer is a two pack epoxy primer for use over a wide range of substrates. It contains zinc phosphate giving added corrosion resistance for greater durability. The product can be air dried or stoved giving flexibility in production. It is available in white and grey as standard, it can also be tinted to ensure complete coverage...

Price £134.52
In stock

Carboline Carboweld 11

A weldable pre-construction inorganic zinc primer for shop use only. Designed to protect steel during construction phase of projects under normal conditions. Top Features Weld spatter does not adhere to or damage the coating Dries to touch and to handle in 3 to 5 minutes Flat finish

Price £308.25
In stock

Teamac Zinc Phosphate Primer

An anticorrosive primer on iron and steel, for use with a range of conventional topcoats such as Teamac Marine Gloss and Teamac Metalcote Plant Enamel.

Price £14.12
In stock

Jotun Barrier 77

From Jotun, this primer is for structural steel and piping in highly corrosive environments, ideal for offshore environments, refineries, power plants, bridges, buildings, mining equipment and general structural steel. Jotun Barrier 77 is a two component polyamide cured zinc rich epoxy coating.

Price £124.78
In stock

Carboline Carboguard 893 MIO

A high solids corrosion resistant primer or intermediate coat on concrete, steel and (in)organic zinc primers. Top Features Excellent corrosion protection. Excellent film build and edge protection. VOC compliant to current AIM regulations.

Price £81.00
In stock

Macropoxy 400

Macropoxy 400 (formerly known as Sherwin-Williams Macropoxy C400V3) multi-functional epoxy zinc phosphate coating is suitable for the protection of steelwork in a range of exposure environments from C1 to C5. It was recently used on The Shard for corrosion protection. Recommended Uses Buildings Car parks Petrochemical plants Breweries...

Price £58.12 Regular price £64.58
In stock

Jotun Penguard Express CF

Jotun Penguard Express CF is a two component polyamide cured, colour stable epoxy primer/finish coating that is fast drying, high solids and high build. It can be used as primer, mid coat or finish coat in atmospheric environments and is specially designed for new construction where fast dry to handle and over coating times are required.

Price £159.07
In stock

Jotun Penguard Special

This product is now only available with a minimum order of 800 litres; for smaller orders, we can recommend Jotun Penguard Express ZP or Jotun Penguard HSP ZP as great alternatives. Jotun Penguard Special is a two component polyamide cured high molecular weight epoxy coating. It is a zinc phosphate pigmented, high build product specially...

Price £138.65
In stock

SikaCor EG 1 Rapid

SikaCor EG 1 Rapid is a fast drying version of the standard SikaCor EG 1. It is a two-pack, high-solids, epoxy-based intermediate coat containing micaceous iron oxide. It is designed as a mechanically resistant intermediate coat on steel surfaces exposed to atmospherical conditions, hot-dip galvanized steel, zinc-spray, stainless steel and aluminium.

Price £159.09
In stock

Sika Permacor 2706 EG

Sika Permacor 2706 EG is a 2-pack mio-protective coating based on epoxy resin with high mechanical resistance and outstanding adhesion. Tested and official approved primer for Sika Unitherm fire protection systems on steel.

Price £251.69
In stock

Jotun Penguard Midcoat

Jotun Penguard Midcoat is suitable for structural steel and piping to be exposed to corrosive environments up to very high. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment. A high solids, high build product designed as a mid coat in systems for new construction in atmospheric environments. Suitable...

Price £30.71
In stock