Sherwin-Williams Macropoxy M902

M902

Sherwin-Williams Macropoxy M902 (formerly known as Epigrip M902) is a low temperature curing hi-build 2-pack epoxy brushing aluminium primer coating capable of curing down to 0°C. 

Colour
Size
£48.33
VAT excluded

£58.00 Tax incl.
Quantity

Description

Sherwin-Williams Macropoxy M902 (formerly known as Epigrip M902) is a low temperature curing hi-build 2-pack epoxy brushing aluminium primer coating capable of curing down to 0°C. 

Recommended Uses

  • For brush application onto hand or mechanically prepared surfaces and/or damp gingered surfaces giving excellent wetting and adhesion characteristics - see datasheet.
  • Suitable for atmospherically exposed surfaces but not recommended for exposure to severe chemical environments. 
  • May be spray applied to blast cleaned surfaces. Recommended where low temperature curing is required or where rapid overcoating is necessary. 

Endorsements

  • BS476 Part 7 - Surface Spread of Flame Material - for details of substrate/scheme, consult Technical Team.
  • Highways Agency Item No.115.
  • Approved by MoD/DRA to Def Stan 80-134.
  • Network Rail Item 7.1.5 

Recommended Buildcoat

Macropoxy M905 

Recommended Topcoats

For overcoating with epoxy products (including self overcoating), the maximum recommended interval is 28 days at 23°C. For overcoating outside this interval, consult Sherwin-Williams technical support for advice.

Where a high degree of gloss and colour retention is required overcoat with Acrolon C137V2, Acrolon C237, Acrolon 1850 and Acrolon 7300 within 7 days at aminimum dft of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature. For overcoating with alkyd systems consult Technical Team for advice. 

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
M902

Data sheet

Application
Brush, Roller, Spray
Coverage
6.0m² per litre
Touch Dry
3.5 Hours
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
16 other products in the same category:

Tor QD High Build Container Coating

Tor QD High Build Container Coating, a semi-gloss, quick-drying high build anti-corrosive primer finish for blast cleaned or mechanically cleaned mild steel. Use to paint containers/plant and equipment in a single coat application. Available in over 400 colours in the RAL and BS range Ready for overcoating after 4 hours Application by...

Price £38.92
In stock

Jotun Penguard WF

Jotun Penguard WF is a two component, anticorrosive water borne epoxy coating that is a versatile, fast drying product containing flash rust inhibitors. It is specially designed for new construction where fast dry to handle and over coating times are required. Jotun Penguard WF can be used as primer, mid coat, finish coat or as single coat...

Price £179.54
In stock

SikaCor EG 1

SikaCor EG 1 is a two-pack, high-solids, epoxy-based intermediate coat containing micaceous iron oxide. The coating is designed as a mechanically resistant intermediate coat on steel surfaces exposed to atmospheric conditions, hot-dip galvanized steel, zinc-spray, stainless steel and aluminium. Features and Benefits  Excellent adhesion...

Price £70.52
In stock

Jotun Barrier

Jotun Barrier is a two component polyamide cured zinc rich epoxy coating. From Jotun, this is a very high zinc dust containing product and it conforms to the compositional requirements of SSPC paint 20, level 2. Jotun Barrier provides very good corrosion protection as part of a complete coating system. To be used as primer in atmospheric...

Price £76.66
In stock

PPG Sigma Vikote 63

PPG Sigma Vikote 63 is a high-build bituminous protective coating for steel, concrete and fibre cement. Offering good resistance to sea and fresh water, PPG Sigma Vikote 63 can be used to protect void spaces, cofferdams, steelwork behind lining and pipes. Good adhesion to steel and galvanised steel Flat finish Black in colour Coverage...

Price £37.40
In stock

PPG NovaGuard 4701

PPG NovaGuard 4701 is a two-part glass flake vinylester primer for concrete and steel as a holding primer for Novaguard 4801. Suitable for service temperature >80°C (176°F) when overcoated with NOVAGUARD 4801 dependent on the actual environment. Mixing ratio by volume: base to catalyst 98:2 Coverage Calculator

Price £405.60
In stock

Nullifire PM018 Primer or Top Seal Epoxy Coating

Nullifire PM018 Primer or Top Seal Epoxy Coating is a two-components modified epoxy coating. It is a heavy duty, high build coating for protection of steel in corrosive environments and is excellent for use at low temperatures. 

Price £311.85
In stock

Hydron Nu-Flame HB Metal Primer

Nu-Flame HB Metal Primer is ideal for priming cast iron and structural steel in preparation to apply the Nu-Flame Fire Retardant System for metals. Advantages Quick dry. Ideal for cast iron and structural steel. 8m²/Litre coverage. 3 colours available. 12-month shelf life.

Price £57.75
In stock

Coo-Var Zinc Phosphate Primer

Coo-Var Zinc Phosphate Primer is a high performance, modified alkyd metal primer. It has very good anti-corrosive properties. Its high durability makes it ideal for use in coastal areas. Product Features Ideal when wood and metal are combined in the same structure as it will prime both surfaces A stronger primer than most basic DIY...

Price £15.29
In stock

HMG Speedbuild 3 Primer

HMG Speedbuild 3 Primer is a 1K, high build, high solids, anti-corrosive primer. Long wet edge time. Quick drying. Can be overcoated with either 1K or 2K topcoats. Click to jump down to Technical Data

Price £45.23
In stock

International Intergard 276

International Intergard 276 is a quick drying two component epoxy primer suitable for overcoating after prolonged periods of weathering, for use at both new construction and maintenance.

Price £189.22
In stock

Cromadex 230 Stoving Primer Filler

Cromadex 230 Stoving Primer Filler is a stoving primer filler containing melamine giving improved durability. The product can be overcoated wet-on-wet enabling rapid application. Cromadex 230 Stoving Primer Filler is available in white as standard, it can also be tinted to ensure complete coverage even on difficult lead free colours.

Price £76.17
In stock

Jotun Penguard Express B11

Jotun Penguard Express B11 can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric environments. Suitable for properly prepared carbon steel, aluminium, concrete and galvanised steel substrates. It can be applied at sub zero surface temperatures.

Price £39.75
In stock

International Interprime 306

International Interprime 306 is a single component, fast drying, high build alkyd primer used as a shop applied post-fabrication primer specifically designed for a blast, fabricate and prime steel production route, and where fast drying and rapid handling properties are required.

Price £38.34
In stock

International Intercure 324

International Intercure 324 is a two component, high solids, low VOC, epoxy zinc phosphate/micaceous iron oxide primer offering excellent barrier protection, low temperature cure and rapid overcoating properties. Pigmented with zinc phosphate anti-corrosive pigment to comply with the requirements of BS5493:1977.

Price £85.76
In stock