Sherwin-Williams Macropoxy M905 (formerly known as Epigrip M905) is a low temperature curing, two pack epoxy high build undercoat, capable of curing down to 0°C.
For application onto suitably primed surfaces, as an undercoat for use under suitable high performance finishes, where low temperature curing is required
Recommended for rapid overcoating and faster handling times
Sherwin-Williams Macropoxy M905 (formerly known as Epigrip M905) is a low temperature curing, two pack epoxy high build undercoat, capable of curing down to 0°C.
Macropoxy M905 is used for application onto suitably primed surfaces, as an undercoat for use under suitable high performance finishes, where low temperature curing is required. It is also recommended for rapid overcoating and faster handling times.
Endorsements
Highways Agency Item No. 116
Network Rail Item Nos 7.1.7 and 7.2.2
Recommended Primers
Compatible with a wide range of epoxy primers, whereby Macropoxy M902 Winterfast Hi-Build Brushing Aluminium is the preferred primer.
Recommended Topcoats
For overcoating with epoxy products (including self overcoating), the maximum recommended interval is 28 days at 23°C. For overcoating outside this interval, consult Sherwin-Williams technical support for advice.
Where a high degree of gloss and colour retention is required overcoat with Acrolon C137V2, Acrolon C237, Acrolon 1850 and Acrolon 7300 within 7 days at a minimum dft of 50 microns or in the case of Acrolon C750V2 overcoat within 4 days. These overcoating times refer to achievement of optimum adhesion at 23°C and will vary with temperature.
For overcoating with alkyd systems consult Technical Team for advice.
Application Conditions & Overcoating
In conditions of high relative humidity, ie 80-85% good ventilation conditions are essential. Substrate temperature shall be at least 3°C above the dew point and always above 0°C.
Application at ambient air temperatures below 5°C is not recommended where there is a risk of ice formation on the substrate.
Due to the high solids content of this material, it is not normally possible to achieve at dry film thicknesses much less than 100 microns by brush application.
Development of satisfactory physical properties including hardness and abrasion resistance will be obtained within 24-48 hours at a temperature of 5°C. Optimum water and chemical resistance will be achieved when the material is fully cured.
If it is desired to overcoat outside the times stated on the data sheet, please seek advice of Technical Team.
Product Details
M905
Data sheet
Manufacturer
Sherwin-Williams
Water / Solvent Based
Solvent
For Use On
Metal
Application Method
Airless Spray, Brush, Roller
Sheen
Mid Sheen
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-Pack
Product Certifications
Highways Agency Item No. 116, Network Rail Item Nos 7.1.7 and 7.2.2
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage