Nullifire PM020 High-Build Alkyd Primer

    NUL0801S1NL
    NUL10611

    Carboline Carbocoat 115 (replaces Nullifire PM020 High Build Alkyd Primer) is a fast-drying steel primer that provides corrosion protection on structural steel. Well suited for fabrication shops that need fast cure to dry and handle times.

    • Rapid cure and fast-drying
    • VOC compliant for most areas
    • Good for filling properties on rough and pitted steel

    Nullifire have made the decision in March 2023 to rebrand Nullifire PM020 High Build Alkyd Primer as Carboline Carbocoat 115 – please see a letter explaining the changes HERE.

    Coverage Calculator

    Colour
    Size
    Finish
    £56.39(ex. VAT)
    £67.67 (inc. VAT)
    Quantity
    Please choose your colour
    In Stock and Available for Delivery (See Delivery Options Below)

    Description

    Carboline Carbocoat 115 is a fast-drying steel primer that provides corrosion protection on structural steel. Well suited for fabrication shops that need fast cure to dry and handle times. May be top-coated with conventional alkyds or acrylics for colour, aesthetics or additional protection.

    When applying a topcoat, Carboline Carbocoat 115 may be coated with Acrylics or Alkyds depending on exposure and need.



    Click To Jump To Section:




    Features & Benefits


    • Rapid cure
    • VOC compliant for most areas
    • Good for filling properties on rough and pitted steel
    • Fast dry to handle properties



    Product Specification


    Technical Data
    Carboline Carbocoat 115
    Volume Solids:51% +/- 2%
    VOC Content:As Supplied : 3.50 lbs./gal (419 g/l)
    Thinner 10 : 6 oz/gal 3.65 lbs./gal (437 g/l)
    Dry Temperature Resistance:Continuous: 200°F (93°C)
    Non-Continuous: 250°F (121°C)
    Theoretrical Coverage Rate:818 ft²/gal at 1.0 mils (20.1 m²/l at 25 microns)
    545 ft²/gal at 1.5 mils (13.4 m²/l at 38 microns)
    409 ft²/gal at 2.0 mils (10.0 m²/l at 50 microns)
    Dry Film Thickness:1.5 - 2 mils (38 - 51 microns) per coat - Do not exceed 3.0 mils in a single coat.
    Topcoats:May be coated with Acrylics or Alkyds depending on exposure and need
    Storage Temperature & Humidity40-110 °F (4-43 °C) - 0-90% Relative Humidity
    Shelf Life24 months at 75 °F (24 °C)



    Drying Times


    Curing Schedule
    Surface TemperatureDry To TouchDry To HandleDry To Topcoat
    35°F (2°C)30 Minutes2 Hours4 Hours
    60°F (16°C)20 Minutes60 Minutes3 Hours
    75°F (24°C)10 Minutes30 Minutes2 Hours



    • These times are based on a 1.5 mil (35 microns) dry film thickness. Higher film thickness, insufficient ventilation, high humidity or cooler temperatures will require longer cure times and could result in solvent entrapment or premature failure. *Dry to topcoat with itself or other alkyds.
    • Recoat intervals may vary from those listed above when using under intumescent fireproofing products. Consult Carboline Technical Service for recommended cure times before applying Carboline intumescent products.



    Surface Preparation


    General

    • Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.

    Steel

    • SSPC-SP6 with a 1.0-2.0 mil (25-50 microns) surface profile for maximum protection. SSPC-SP2 or SP3 as minimum requirement.
    • When using under fireproofing products, defer to the primer surface preparation requirements in the product data sheet of the fireproofing product



    Application Methods


    Product Information
    Conventional Spray:Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, 0.052” I.D. fluid tip and appropriate air cap
    Airless Spray:Pump Ratio: 30:1 (minimum)
    GPM Output: 3.0 (minimum)
    Material Hose: 3/8” I.D. (minimum)
    Tip Size: 0.013-0.017”
    Output PSI: 1800-2000
    Filter Size: 60 mesh
    Brush & Roller (General):For small areas and touch-up only. Avoid excessive re-brushing or re-rolling
    Brush:Use a synthetic bristle brush.
    Roller:Use a short-nap natural roller cover with solvent resistant core.



    Application Conditions


    Product Application Conditions
    ConditionMaterialSurfaceAmbientHumidity
    Minimum35°F (2°C)35°F (2°C)35°F (2°C)0%
    Maximum120°F (49°C)120°F (49°C)120°F (49°C)95%



    • This product simply requires the substrate temperature to be above the dew point.
    • Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate.
    • Special application techniques may be required above or below normal application conditions.



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    Product Details
    10611-991898

    Data sheet

    Manufacturer
    Nullifire
    Water / Solvent Based
    Solvent
    For Use On
    Steel
    Application Method
    Conventional Spray, Airless Spray, brush, roller
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Single
    Pack Size
    5L
    UN Number
    UN1263
    Base Type
    Alkyd
    Suitable For Use On
    Structural Steel
    Application Method
    Roller
    Application Method
    Brush
    Application Method
    Spray
    Product Usage Type
    Primer
    Colour Family
    Red
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    Nullifire PM020 High-Build Alkyd Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    COVERAGE CALCULATOR
    Units
    Film Thickness
    Total area²
    Or enter length and width dimensions:
    Length
    Width

    *All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage

    You might also like

    Carboline Thinner 2

    Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info

    Price £32.63 (ex. VAT)
    In Stock and Available for Delivery

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery