PPG AquaCover 20 (also known as Sigma Aquacover 20) is a one-component waterborne, high-build zinc phosphate primer/coating, based on acrylic dispersion. It can be overcoated with most waterborne acrylics, solvent-borne epoxy coatings and alkyd paints, as well as certain solvent-borne, two-component products. Useful for when solvents are...
Nullifire PM021 General Purpose Epoxy Primer
Nullifire PM021 General Purpose Epoxy Primer is a two-components epoxy polyamide primer with excellent resistance to salts, water and alkalies, and with very good resistance to mild acids and solvents.
Nullifire PM021 General Purpose Epoxy Primer is a two-components epoxy polyamide primer with excellent resistance to salts, water and alkalies, and with very good resistance to mild acids and solvents. It can be used on steel and concrete substrates.
Features & Benefits
- Excellent corrosion resistance
- Cured film is tough and abrasion resistant
- Used 40% diluted as a tie-coat over zinc silicate and metallized steel
- Excellent adhesion to aluminium
- Widely used within petrochemical, offshore and shipping industries
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
Sherwin-Williams Macropoxy M902 (formerly known as Epigrip M902) is a low temperature curing hi-build 2-pack epoxy brushing aluminium primer coating capable of curing down to 0°C.
A metal primer with surface tolerant properties, can also be used as an intermediate coat, or self-priming finish over steel and zinc primers. Top Features Ready to apply after mixing Economical fit for use epoxy Used as a primer, intermediate, or finish coat VOC compliant to current AIM regulations
Nu-Steel Zinc Rich Primer has been specifically-formulated to prime mild steel surfaces to prepare it for overcoating with the finish of your choosing. Steel with low carbon is termed as mild steel, and such uses of this type of steel include: signs, furniture, fencing, cars and structural steel. Advantages Interior and exterior use. 3-5m²/Litre....
Nu-Steel TP Aluminium Primer is an epoxy-based coating, for use on properly prepared steelwork, such as parapet/guard rails, bridges and architecture. Advantages Metallic Aluminium finish. Touch-dry in 3 hours. 8m²/Litre average coverage. 12-month shelf life.
A rust preventing primer. Typically used as a primer above water line on areas like superstructure, topside, deck, stores room, cargo hold etc. Top Features Quick drying, White Spirit based alkyd primer May be topcoated with alkyd paints as recommended Can be thinned
An epoxy primer excellent anti-corrosion properties this primer is the perfect choice for steel and iron gutters or any other steel/iron surface. Top Features Good anti-corrosion properties Brush or airless spray applicable Application temperature from +5℃ (substrate)
Sherwin-Williams Transgard TG111V2 is a high build 2-pack epoxy zinc phosphate primer/buildcoat, designed as anti-corrosive protection of carbon steel surfaces prepared by abrasive blast cleaning.
PPG SigmaWeld 199 is a two-component, moisture-curing low zinc (ethyl) silicate prefabrication primer that is suitable for automatic application on shot blasted steel plates. Good cutting and excellent welding properties, including MIG/MAG welding in various positions (either automatic or manual welding), fast-drying and low fume release are...
An all-purpose immersion-grade epoxy that has a variety of attributes including low-temperature cure, surface tolerance and fast recoat times. Can be used direct to metal as a corrosion resistant primer or as an intermediate coating over other primers. Top Features Excellent corrosion protection Excellent application characteristics Fast...
International Interplate 855 is a fast drying, two component, weldable zinc silicate pre-fabrication primer for application by manual or automatic spray used as a temporary protective primer for the coating of steelwork prior to the fabrication process.
Nu-Steel® TP Etch Primer is a two pack primer giving excellent adhesion to metals prior to subsequent paint systems. Advantages Up to 8 years protection. Available in yellow or grey. 15m²/Litre approx. coverage rate. 12-month shelf life.
Quick Air Dry High Build Primer for blasted and non-blasted steel, a one-pack post-fabrication primer that dries fast for a quick turnaround. Suitable for use in mild to moderate corrosive environments, such as those typically found in commercial buildings, hospitals and schools. Features: Overcoatable with Cromadex 222, 233 & 400...
Jotun Resist 86 is a two component moisture cured inorganic zinc ethyl silicate coating that is a fast curing, very high zinc dust containing product. Specially designed by Jotun as a primer in coating systems where extended durability is required. It provides a solid foundation for the optimal performing coating system in the toughest...