Bradite Barrier Primer
  • Bradite Barrier Primer

Bradite Barrier Primer

EU96

Bradite Barrier Primer is a high performance two pack epoxy solvent based barrier primer for ferrous and non-ferrous metals, providing outstanding adhesion and excellent corrosion protection. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004.

Advantages

  • Suitable as a primer for a wide range of coatings
  • Can be used in immersion conditions
  • Conforms with parts KU1 A/B of B5493

Colour
Size
£68.89
VAT excluded

£82.67 Tax incl.
Quantity

Description

Bradite Barrier Primer is a high performance epoxy solvent based barrier primer for ferrous and non-ferrous metals which acts as a primer for suitably prepared steel and non-ferrous substrates providing outstanding adhesion and excellent corrosion protection.

May be used as a wet blast primer and for immersion application when part of a suitable coating system.

Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems. 2004/42/EC EU limit value for this product (cat.A/j sb): 500g/l (2010). This product contains max. 429 g/l VOC.


Features & Benefits

  • Suitable as a primer for a wide range of coatings.
  • Excellent adhesion to steel, galvanised steel and non-ferrous metals.
  • Can be used in immersion conditions.
  • Two-pack epoxy system.
  • Conforms with parts KU1 A/B of B5493.


Preparation

Industrial protective coating: High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil.

For new or total repair, steel should be blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns. (For maintenance repair, sweep blast or mechanically abrade existing coating to provide a key. Damaged or rusty areas should be blast cleaned to SIS Sa 21/2 or mechanically to SIS St 3 minimum).

1st coat: Bradite Epoxy Barrier Primer EU96.

2nd coat: Bradite HB MIO Epoxy Build Finish EM97.

3rd coat: Bradite Polyurethane Gloss Finish PG77.

4th coat: Bradite Polyurethane Gloss Finish PG77.

For maintenance painting, the 1st coat will be a touch up to bare areas only.

Wet blasted steel: High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil.

Steel should be wet blast cleaned to SIS Sa 21/2 minimum with a blast profile of 35-50 microns then rinsed with fresh water, with excess water being blown off with oil free compressed air. (For maintenance repair, wet blast as previous, feather existing coating to a sound edge and abrade to provide a key.)

1st coat: Bradite Epoxy Barrier Primer EU96.

2nd coat: Bradite HB MIO Epoxy Build Finish EM97.

3rd coat: Bradite Polyurethane Gloss Finish PG77.

For maintenance painting, the 1st coat will be a touch up to bare areas only.


Application

Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.

Brush and Roller: supplied ready for use. Thin, if required, with 0-5% Bradite Thinner TE36. 

Conventional Air Spraying: Thin with 10-25% Bradite Thinner TE36 as required, tip size – 23 thou (1.7mm), tip pressure 60psi (0.4MPa) approximately.

Airless Spraying: Thin with 0-25% Bradite Thinner TE36 as required, tip size - 18 thou (0.46mm) approximately, tip pressure - 2100 psi (15MPa) approximately.

Clean all equipment immediately after use with Bradite Thinner TE36 for best results. Always refer to the Health and Safety sheet for the product before use, and observe the warning phrases on the label.

Product Details
EU96

Data sheet

Manufacturer
Bradite
Water / Solvent Based
UN1263
For Use On
Steel, non-ferrous metals
Application Method
Brush, roller, Airless Spray, Conventional Air Spray
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-pack
Product Certifications
ISO 9001:2008, ISO 14001:2004 environmental management systems
Pack Size
5L
Coverage
10m2 per Litre
Touch Dry
30 Mins
UN Number
UN1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send