A high performance two pack epoxy solvent based barrier primer for ferrous and non-ferrous metals, providing outstanding adhesion and excellent corrosion protection. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Suitable as a primer for a wide range of coatings Can be used in immersion conditions...
Bradite Fastrac GP Anti-Corrosive Primer
A fast drying modified alkyd anti-corrosive primer for use as a general-use fast drying prefabrication or system primer on properly prepared ferrous surfaces. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004
- Protects against corrosion on properly prepared steel
- Pigmented with zinc phosphate
- Touch dry in as little as an hour
- Flat sheen
Bradite Fastrac GP Anti-Corrosive Primer is a fast drying anti-corrosive primer for use as a general-use fast drying prefabrication or system primer on properly prepared ferrous surfaces. Available in Dark Grey and Red Oxide shades that provide a flat sheen primer on structures, such as:
- Shipping containers
- Industrial plants
Touch dry in as little as one hour, this primer gives you peace of mind that a realistic turnaround time can be agreed between project managers and contractors.
Manufactured under the auspices of an ISO 9001:2008 quality & ISO 14001:2004 environmental management systems.
Product Use in the Workplace
- Metal fence - Although built as a barrier, it is fairly common for fences to be touched or climbed on. I think we all have some fence-climbing stories from our childhood to tell. It's therefore important that the fence is kept in top condition and free from rust and flaking that can cause discomfort or harm to individuals.
- Shipping container - Shipping goods all over the world means these structures are not only out all year round but also spend much time at sea, exposed to the full battle of the elements eroding away the metal.
- Storage facility - Protecting the items inside the facility is of prime importance. No storage facility can offer full protection if water and moisture are eating away at the structure, which will only serve to increase the potential of damaged goods inside.
- Factory - Exposed to contaminants, metalwork in factories need a protective layer that resists against corrosion.
Features & Benefits
- Fast drying modified alkyd primer for steel.
- Pigmented with zinc phosphate.
- Protects against corrosion on properly prepared steel.
- Flat sheen.
- Touch dry in as little as an hour.
High pressure steam cleaning to remove all loose, flaking paint and contamination back to a sound surface. Bradite TD39 industrial strength detergent, washing and rinsing should be used with scrubbing to remove grease or oil.
Remove all rust scale, loose mill scale or other corrosion products by scraping and mechanical cleaning to SIS-St 3 (ISO 8501-1:1998).
Intact areas of existing coatings should be roughened by abrasive manual or disc sanding, feathering back to a sound coating edge. Cracks and pits should be filled using a suitable metal filler before painting. Substrate should be dust free and completely dry before coating.
Light surface rusting may be effectively treated using one coat of Bradite FASTRAC Rust Converter RC46 prior to application of Bradite FASTRAC GP Anticorrosive Primer AP70.
New galvanised steel should be thoroughly degreased and then pre-treated with Bradite Mordent Solution TM38 prior to application of Bradite FASTRAC GP Anticorrosive Primer AP70. Alternatively, or for other nonferrous metals, prime with Bradite Barrier Primer EU96 before application of selected Bradite finish.
Suitable for use under many Bradite finishes such as Fastrac Gloss ME53 & Fastrac Satin SE53.
Application and use should always conform to the codes of practice described in BS 6150 and BS 5493.
Brush and Roller: supplied ready for use. Thin with 0-5% Bradite Thinner TW35 if required.
Conventional Air Spraying: Thin with 10-20% Bradite Thinner TW35 as required, tip size - 2.0mm, tip pressure 60psi (0.4MPa) approximately.
Airless Spraying: Thin with 0-15% Bradite Thinner TW35 as required, tip size - 19 thou (0.48mm) approximately, tip pressure - 2100 psi (15MPa) approximately.
Clean all equipment immediately after use with Bradite Thinner TW35 for best results. Always refer to the Health and Safety sheet for the product before use and observe the warning phrases on the label.
It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.
Be the first to ask a question about this product!
A metal primer for ferrous metals such as iron and steel that offers sound anti-corrosion properties and superb capacity and coverage. Can be used over existing paintwork. Examples of Use Bridges Metal artwork Metal trusses Warehouses Factories
A high performance single pack water based rust converter for the treatment and passivation of surface rust on all hand or mechanically prepared rusty ferrous surfaces. Manufactured under the auspices of an ISO 9001:2008 & ISO 14001:2004. Advantages Converts low level corrosion to an inert substrate for painting Suitable for...
A heavy duty, high build coating for protection of steel in corrosive environments. Gives a hard and smooth surface with excellent flexibility. Top Features Excellent immersion performance in water. Suitable as a rust preventing coating in ballast tanks. Ideal for areas prone to condensation. Very good abrasion resistance.
Teamac Rust Converter is an excellent product to stop the rusting process and allow rusty surfaces to be overcoated: Easy to apply, and ideal for marine and industrial applications Can be applied to rust in existing damp conditions Suitable for rusted iron or steel Application by brush, roller or airless spray To be overcoated with a...
Jotun Penguard Midcoat is suitable for structural steel and piping to be exposed to corrosive environments up to very high. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment. A high solids, high build product designed as a mid coat in systems for new construction in atmospheric...
A durable and high performance acrylic coating for use where excellent weathering properties and chemical resistance are required. Use as a direct-to-metal acrylic coating for structural steel, as well as other exterior and interior uses. Top Features Smooth, attractive, high build finish Excellent corrosion protection Meets most VOC...
International Intercure 420 is a two component, high solids, low VOC epoxy micaceous iron oxide coating formulated on proprietary polymer technology which provides rapid cure and overcoating even under low temperature conditions.
A high-build epoxy mastic coating used for atmospheric exposed and submerged steel. Top Features Excellent film build and edge protection Surface tolerant characteristics Cures at low temperature
PPG Dimetcote 9 (also known as Sigmazinc 9), is a two-component, moisture-curing zinc (ethyl) silicate coating for structural steel that can withstand substrate temperatures from –90°C (–130°F) up to 400°C (750°F), with good resistance to impact and abrasion. Anti-corrosive primer for structural steel. Specified for structural joints...
A heavy-duty primer formulated to provide long term protection of structural steel. It provides excellent adhesion and can be welded through to yield sound welds. Top Features Good for extended exposure demands Ability to be welded through Heavy-metal free
An inexpensive primer based upon iron oxide for use on structural steelwork, iron and metalwork which can be left as a short term finish or overcoated with Teamac Marine or Industrial coatings.
Sherwin-Williams Dura-Plate UHS Primer with Opti-Check OAP (Optically Activated Pigments) technology is a specially designed primer for use under Sherwin-Williams Dura-Plate UHS. It is ideal for use over prepared steel or concrete surfaces in industrial and marine exposures.
A primer from Rust-Oleum to make difficult smooth surfaces coatable. CombiPrimer Adhesion is ideal for use on galvanised steel, stainless steel, aluminium, copper, glass, porcelain and other smooth, dense surfaces that normal paints cannot stick to.
International Interplate 855 is a fast drying, two component, weldable zinc silicate pre-fabrication primer for application by manual or automatic spray used as a temporary protective primer for the coating of steelwork prior to the fabrication process.