Carboline Carbocrylic 3358 IMC is an intermediate coat on steel or concrete in a three coat system, and can be topcoated with several generic types of topcoats. Excellent abrasion resistance and flexibility with good chemical resistance.
Single component
Fast drying
Low VOC
Eggshell finish
This product is only available as PRICE ON APPLICATION - For more information and to place an order please contact us on 0113 2455450or email [email protected].
Carboline Carbocrylic 3358 IMC is an intermediate coat on steel or concrete in a three coat system, and can be topcoated with several generic types of topcoats. Excellent abrasion resistance and flexibility with good chemical resistance.
Slight discoloration and loss of gloss may be observed above 100°C
Theoretrical Coverage Rate:
4,2 m²/l at 100 µm
Allow for loss in mixing and application
Dry Film Thickness:
75 – 150 µm per coat, normally 100 µm
Wet Film Thickness:
180 – 360 µm per coat, normally 240 µm
Topcoats:
Normally topcoated with Carbocrylic 3359 TC. Other waterborne topcoats may be used.
Limitations:
Not recommended for immersion service
Shelf Life:
24 months at 24°C
Storage:
Store indoors. Keep from freezing.
Storage Temperature & Humidity:
5° - 45°C, 0-95% RH
Drying Times
Curing Schedule
Surface Temperature
Dry To Topcoat
Dry To Touch
10°C (50°F)
3 Hours
45 Minutes
25°C (77°F)
1.5 Hours
30 Minutes
35°C (95°F)
1 Hour
20 Minutes
Actual surface dry and dry to topcoat times will depend upon film thickness, air humidity, ventilation and other local conditions.
Above times should be considered as guidelines provided good ventilation conditions.
Surface Preparation
General
Surface must be clean and dry. Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.
Steel
Normally applied over clean and dry recommended primers. When applied directly to steel, blast clean to min. Sa2 or power tool clean to St2 (ISO 8501-1).
Concrete
Apply over clean and dry surface. Concrete must be cured min. 28 days at 24°C and RH 50% or equivalent. A test patch is recommended to check adhesion.
Application Methods
Product Information
Mixing:
Power mix until uniform in consistency. Avoid excessive air entrapment.
Thinning:
May be thinned up to 5% with clean potable water
General:
Pre-rinse equipment with butyl glycol followed by clean potable water before spraying.
Airless Spray:
Pump Ratio: 30:1 (minimum)
GPM Output: 3.0 (minimum) 12 liters/min
Material Hose: 3/8" I.D. (minimum)
Tip Size: 0.013” - 0.017”
Output PSI: 1800-2200
Filter Size: 60 mesh
Teflon packings are recommended
Brush & Roller (General):
Use a synthetic bristle brush or short nap synthetic roller cover with phenolic core.
Application Conditions
Product Application Conditions
Condition
Material
Surface
Ambient
Humidity
Minimum
10°C (50°F)
10°C (50°F)
10°C (50°F)
0%
Maximum
40°C (104°F)
50°C (122°F)
40°C (104°F)
80%
Do not apply when the surface temperature is less than 3°C above the dew point. Do not apply if temperatures are expected to drop below 10°C within 24 hours of application.
Film thickness above recommendations may reduce product properties.
Health & Safety
Clean Up
Use clean potable water followed by butyl glycol or other suitable solvent to dry equipment. In case of spillage, absorb and dispose of in accordance with local applicable regulations.
Safety
Read and follow all caution statements on this product data sheet and on the MSDS for this product. Employ normal workmanlike safety precautions. Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands and all exposed areas.
Refer to the safety data sheet in the attachments section above and tin label prior to use.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3).
Please click here for important information about these kits.
Kit Contents:
SET 1 (Hand Tools)
1 x Rust-Oleum...
• These colour samples are to be used for guidance only.
• Product contained within is generic to provide a close representation to your chosen colour.
• Should not be used to carry out any painting project, this is for colour selection purposes only and does not remove the need for you to ensure the correct product is chosen and tested for your application once a colour has been decided on.
• It is not a sample of the product you intend to purchase/use and cannot be used to test anything other than colour appearance.
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application, batches variances number of coats and substrate surface.
• We cannot therefore promise that the colour of the product you ultimately purchase will exactly match the colour of this colour sample.
• Once you have selected a colour, you must purchase the smallest amount of the product you intend to use in your chosen colour and apply to a small, inconspicuous test area to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
Colourmatch Service Disclaimer
• Notwithstanding any other provision of our conditions of sale, you agree and understand that many factors affect the colour of a painted product, including lighting, sheen level, method of application and product surface.
• We cannot therefore promise that the colour of the product you paint with the Kolorbond paint will exactly match the colour of the item you send to us.
• You must therefore purchase the smallest Kolorbond paint pot available first and then apply the paint to a small, and where possible hidden, test area of your product to be sure that it meets your expectations.
• Leave the product for 24 hours and then only buy more paint and/or apply more paint to your product if you are completely happy with the results on the test area.
• We cannot be liable to you for any loss or damage if you have not complied with this process.
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
*All estimates are based on theoretical consumption rates for a single coat and do not take into account any substrate deviations or wastage
