Carboline Carboguard 633

8170

Carboline Carboguard 633 is a heavy duty, high build primer or intermediate coating for protection of steel in corrosive environments. Can be used on aluminium and galvanization.

  • Fast overcoatable with 2K topcoats
  • Quick drying - can be recoated after 3 hours (at 23°C)
  • Can be applied in temperatures as low as -5°C
  • Excellent anti-corrosive properties
  • Excellent flowability, also at low DFT
  • Incredibly good abrasion resistance
  • Approved for Grain (Newcastle Occupational Health and Hygiene)

Colour
Size
Finish
£145.80
£174.96 Incl. VAT
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

100% secure payments
Description

Carboline Carboguard 633 is a heavy duty, high build primer or intermediate coating for protection of steel in corrosive environments. Can be used on aluminium and galvanization. Cures at low temperature and can be over-coatable relatively quickly.



Click To Jump To Section:




Features and Benefits


  • Fast overcoatable with 2K topcoats
  • Excellent anti-corrosive properties
  • Applicable as one-coat system up to corrosion class C4 (ISO 12944-2)
  • Applicable up to corrosion class C5(H) with suitable primer
  • Excellent flowability, also at low DFT
  • Incredibly good abrasion resistance
  • Semi-gloss finish



Product Specification


Technical Data
Carboline Carboguard 633
Volume Solids: 74 ± 2%
Dry Temperature Resistance: Continuous: 120°C (248°F)
Non-continuous: 150°C (302°F)
Theoretical Coverage Rate: 6.2 m²/l at 120 µm DFT. Allow for loss in mixing and application.
Dry Film Thickness: 80 - 200 microns (3.15 - 7.87 mils) per coat
Wet Film Thickness: 110 - 270 µm per coat
Limitations: Epoxies discolour and eventually chalk in sunlight exposure
Topcoats: Carbothane 156 SG for ISO 12944-systems. Other topcoats according to Carboline recommendations
Approvals: Grain, Newcastle Occupational Health and Hygiene
Shelf Life: 24 months at 24°C
Storage Temperature and Humidity: 5°- 45°C. 0 - 95% relative humidity



Drying Times


Curing Schedule
Surface Temp Cure for Service Dry to Handle Dry to Touch Dry to Recoat
-5°C (23°F) 30 Days 48 Hours 24 Hours 24 Hours
5°C (41°F) 21 Days 20 Hours 10 Hours 10 Hours
10°C (50°F) 14 Days 12 Hours 6 Hours 6 Hours
15°C (59°F) 7 Days 8 Hours 4 Hours 4 Hours
23°C (73°F) 5 Days 6 Hours 3 Hours 3 Hours



  • The above times are based on recommended DFT. higher DFT, insufficient ventilation or lower ambient temperatures would cause longer curing times.
  • Maximum recoating time up to 6 months depending on temperature and curing conditions.



Surface Preparation


General

  • Surfaces must be clean and dry. Employ adequate methods to remove dirt, dust, oil, and all other contaminants that could interfere with adhesion of the coating.

Steel

  • Abrasive blast cleaning to min. Sa 2 (ISO 8501-1)

Galvanised Steel

  • Light sweep-blasting to attain even roughness (SaS)

Aluminium

  • Light sweep-blasting to attain even roughness (SaS)
  • Alternatively wash surface with alkaline detergent, e.g. Carboline Surface Cleaner No.3.



Application Methods


Product Information
Mixing: Power mix separately, then add part B to part A and power mix. DO NOT MIX PARTIAL KITS
Ratio: 2 : 1 (A to B) by volume
Thinning: Typically, not necessary
May be thinned up to 10% with Carboline Thinner #2
Pot Life: 1.5 hour at 20°C and longer at lower temperatures.
Airless Spray: Pump ratio: 30:1 (min.)
GMP output: 3.0 (min.)
Material hose: 3/8” I.D. (min.)
Tip size: .015-.019”
Output PSI: 2400
Filter size: 60 mesh
Brush and Roller (General): For small areas and stripe coating only. Multiple coats may be required to obtain desired appearance, recommended dry film thickness and adequate hiding.
Brush: Use a medium bristle brush
Roller: Use a medium nap phenolic core roller



Application Conditions


Product Conditions
Condition Material Surface Ambient Humidity
Minimum -5°C (23°F) -5°C (23°F) -5°C (23°F) 0%
Maximum 35°C (95°F) 50°C (122°F) 40°C (104°F) 85%



  • Industry standards are for substrate temperatures to be 3°C above the dew point.
  • Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate.
  • Special application techniques may be required above or below normal application conditions.



Health and Safety


Clean Up

  • Use Carboline Thinner #2 or Acetone.
  • In case of spillage, absorb and dispose of in accordance with local applicable regulations.

Safety

  • Read and follow all caution statements on this product data sheet and on the MSDS for this product.
  • Employ normal workmanlike safety precautions.
  • Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands, and all exposed areas.

Ventilation

  • When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
  • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used.

Caution

  • This product contains flammable solvents.
  • Keep away from sparks and open flames.
  • All electrical equipment and installations should be made and grounded in accordance with applicable regulations.
  • In areas where explosion hazards exist, workmen should be required to use nonferrous tools and wear conductive and non-sparking shoes.
  • Refer to the product and safety data sheet in the attachments section above for further details.
Product Details
8170

Data sheet

Manufacturer
Carboline
Water / Solvent Based
Solvent
For Use On
Steel, Galvanized Steel, Aluminum
Application Method
Airless Spray, brush, roller
Sheen
Semi-gloss
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-pack
Product Certifications
Grain- Newcastle Occupational Health and Hygiene
Pack Size
15L
Mixing Ratio
2 : 1 (A to B) by volume
Coverage
6.2 m²/l at 120 µm DFT. Allow for loss in mixing and application.
Compatible Topcoats
Carbothane 156 SG for ISO 12944-systems. Other topcoats according to Carboline recommendations
Max. Application Temperature
Material: 35°C (95°F) - Surface: 50°C (122°F) - Ambient: 40°C (104°F)
Min. Application Temperature
Material: -5°C (23°F) - Surface: -5°C (23°F) - Ambient: -5°C (23°F)
Shelf Life (from date of manufacture)
24 months at 24°C
Recommended Dry Film Thickness
80 - 200 microns (3.15 - 7.87 mils) per coat
Recommended Wet Film Thickness
110 - 270 µm per coat
UN Number
UN1263
Dry to Recoat (at 10°C)
6 Hours
Fully Cured (at 10°C)
14 Days
Touch Dry (at 10°C)
6 Hours
Pot Life
1.5 hour at 20°C and longer at lower temperatures.
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22
In Stock and Available for Delivery