Carboline Carboguard E 19 Primer

8101

Carboline Carboguard E 19 Primer is a two-component epoxy polyamide primer containing zinc phosphate. A versatile epoxy primer with excellent resistance to salts, water and alkalies, with very good resistance to mild acids and solvents.

  • Excellent corrosion resistance
  • Cured film is tough and abrasion resistant
  • Used 40% diluted as a tie-coat over zinc silicate and metallized steel
  • Excellent adhesion to aluminium
  • Widely used within petrochemical, offshore and shipping industries
  • Flat finish

Colour
Size
Finish
£65.25
£78.30 Incl. VAT
Quantity
Please choose your colour
Available for Delivery (See Delivery Options Below)

Description

Carboline Carboguard E 19 Primer is a two-component epoxy polyamide primer containing zinc phosphate. A versatile epoxy primer with excellent resistance to salts, water and alkalies, with very good resistance to mild acids and solvents.



Click To Jump To Section:




Features and Benefits


  • Excellent corrosion resistance
  • Cured film is tough and abrasion resistant
  • Used 40% diluted as a tie-coat over zinc silicate and metallized steel
  • Excellent adhesion to aluminium
  • Widely used within petrochemical, offshore and shipping industries
  • Flat finish



Product Specification


Technical Data
Carboline Carboguard E 19 Primer
Volume Solids: 50 ± 2%
Theoretical Coverage Rate: 5,0 m²/l at 100 µm
Allow for loss in mixing and application.
Dry Film Thickness: 30 - 200 microns (1.18 - 7.87 mils) per coat
Normally 75 µm
Wet Film Thickness: 60 – 400 µm per coat, normally 150 µm
Dry Temperature Resistance: Continuous: 120°C (248°F)
Non-Continuous: 150°C (302°F)
Primer: Self-priming
Topcoats: May be topcoated with epoxy, vinyl, polyurethane or other coatings as recommended by Rawlins on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Limitations: Not recommended for immersion service in strong acids or exposures in areas where chalking is undesirable.
Shelf Life: Part A: 24 months at 24°C
Part B: 36 months at 24°C
Storage Temperature and Humidity: 5°C - 45°C
0 - 95% relative humidity



Drying Times


Curing Schedule
Surface Temp. Dry to Touch Dry to Recoat Final Cure
5°C (41°F) 4 Hours 20 Hours 21 Days
15°C (59°F) 2 Hours 15 Hours 14 Days
25°C (77°F) 1 Hour 5 Hours 10 Days



  • These times are based on 75 µm DFT. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure.



Surface Preparation


General

  • Surface must be clean and dry.
  • Employ adequate methods to remove dirt, dust, oil and all other contaminants that could interfere with adhesion of the coating.

Steel

  • Abrasive blasting to min. Sa 2½ (ISO 8501-1)
  • Alternatively, ultra high pressure water jetting to Nace No. 7 min. C Vis WJ-2. Max flash rust; C Vis WJ-2M.

Concrete

  • Concrete must be cured at least 28 days at 24°C and 50% relative humidity or equivalent.
  • Prepare surfaces in accordance with ASTM D42582 Surface Cleaning of Concrete and ASTM D4259 Abrading Concrete.
  • Voids in concrete may require surfacing



Application Methods


Product Information
Mixing: Power mix separately, then combine and power mix. DO NOT MIX PARTIAL KITS.
Thinning: May be thinned up to 40% with Carboline Thinner 15
Ratio: 2 : 1 (A to B) by volume
Pot Life: 6 hours at 23°C and higher at lower temperatures
Airless Spray: Pump Ratio: 30:1 (min)
GPM Output: 3.0 (min)
Material Hose: 3/8” (0.38 cm) I.D. (min)
Tip Size: 015-.021”
Output PSI: 2000
Filter Size: 60 mesh
Brush and Roller (General): For small areas and stripe coating. Multiple coats may be required to obtain desired appearance, and recommended dry film thickness.
Brush: Use a medium bristle brush
Roller: Use 3/8” nap solvent resistant core roller



Application Conditions


Product Conditions
Condition Material Surface Ambient Humidity
Minimum 5°C (41°F) 5°C (41°F) 5°C (41°F) 0%
Maximum 40°C (104°F) 50°C (122°F) 50°C (122°F) 85%



  • Industry standards are for substrate temperatures to be 3°C above the dew point.
  • Condensation due to substrate temperatures below the dew point can cause flash rusting on prepared steel and interfere with proper adhesion to the substrate.
  • Special application techniques may be required above or below normal application conditions.



Health and Safety


Clean Up

  • Use Thinner 2 or Acetone
  • In case of spillage, absorb and dispose of in accordance with local applicable regulations.

Safety

  • Read and follow all caution statements on this product data sheet and on the SDS for this product.
  • Employ normal workmanlike safety precautions.
  • Hypersensitive persons should wear protective clothing, gloves and use protective cream on face, hands, and all exposed areas.

Ventilation

  • When used as a tank lining or in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
  • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used.

Caution

  • This product contains flammable solvents
  • Keep away from sparks and open flames
  • All electrical equipment and installations should be made and grounded in accordance with applicable regulations.
  • In areas where explosion hazards exist, workmen should be required to use nonferrous tools and wear conductive and non-sparking shoes.
  • Refer to the product and safety data sheet in the attachments section above for further details.
Product Details
8101

Data sheet

Manufacturer
Carboline Carboguard E 19 Primer
Water / Solvent Based
Solvent
For Use On
Steel, Concrete
Application Method
Airless Spray, Brush, Roller
Sheen
Flat
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Two-pack
Pack Size
5L
Mixing Ratio
2 : 1 (A to B) by volume
Coverage
5,0 m²/l at 100 µm
Compatible Topcoats
May be topcoated with epoxy, vinyl, polyurethane or other coatings as recommended by Rawlins
Max. Application Temperature
Material: 40°C (104°F) - Surface: 50°C (122°F) - Ambient: 50°C (122°F) - Humidity: 0%
Min. Application Temperature
Material: 5°C (41°F) - Surface: 5°C (41°F) - Ambient: 5°C (41°F) - Humidity: 0%
Solids by Volume
50 ± 2%
Shelf Life (from date of manufacture)
Part A: 24 months at 24°C - Part B: 36 months at 24°C
Touch Dry
1 Hour @ 25°C (77°F)
Recommended Dry Film Thickness
30 - 200 microns (1.18 - 7.87 mils) per coat
Recommended Wet Film Thickness
60 – 400 µm per coat, normally 150 µm
UN Number
UN1263
Dry to Recoat
5 Hours @ 25°C (77°F)
Fully Cured
10 Days @ 25°C (77°F)
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Carboline Thinner 15

Carboline Thinner 15 is a thinner for use in industrial coatings. More Information

Price £43.05
In Stock and Available for Delivery

Carboline Thinner 2

Carboline Thinner 2 is a thinner for use in industrial coatings. More Information

Price £42.83
In Stock and Available for Delivery

Surface Preparation Kits for Steel

These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools) 1 x Rust-Oleum...

Price £17.22
In Stock and Available for Delivery