Carboline Phenoline 311 Primer

    0629A1NL

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    Carboline Phenoline 311 Primer is a two-component, tank lining holding primer that has a variety of attributes including low-temperature cure, fast recoat times, moisture tolerance during application and cure, and excellent blast-hold protection. Often used with thick film lining systems as a holding primer (maintain blast cleaning) and is suitable for both new tanks and relines.

    • Approved for potable water, ANSI/NSF standard 61 if manufactured at certified location
    • Low temperature cure (6°C)
    • Excellent blast-hold protection
    • Suitable for use over damp concrete
    • Excellent application characteristics
    • Fast recoat times
    • Moisture tolerance during application
    • Meets VOC restrictions
    • Low HAP’s content

    Quantity
    Product not available
    This Product has been Discontinued

    Description

    Carboline Phenoline 311 Primer is a two-component tank lining holding primer that has a variety of attributes including low-temperature cure, fast recoat times, moisture tolerance during application and cure, and excellent blast-hold protection.

    Phenoline 311 Primer is often used with thick film lining systems as a holding primer (maintain blast cleaning) and is suitable for both new tanks and relines. It exhibits excellent surface wetting characteristics and quick cure for handling. It contains high levels of inert flake reinforcement. Excellent for use as a bonding primer for linings when damp concrete or masonry substrates are encountered.



    Click To Jump To Section:




    Features and Benefits


    • Approved for potable water, ANSI/NSF standard 61 if manufactured at certified location
    • Low temperature cure (6°C)
    • Excellent blast-hold protection
    • Suitable for use over damp concrete
    • Excellent application characteristics
    • Fast recoat times
    • Moisture tolerance during application
    • Meets VOC restrictions
    • Low HAP’s content



    Product Specification


    Technical Data
    Carboline Phenoline 311 Primer
    Volume Solids:47% +/- 2%
    Theoretical Coverage Rate:

    18.5 m²/l at 25 microns

    6.2 m²/l at 75 microns

    Allow for loss in mixing and application
    Dry Film Thickness:25 - 76 microns typical
    Do not exceed 3 mils
    HAPs Values:1.64 lbs/solid gallon
    VOC Values:

    Per EPA Method 24: 231 g/l mixed

    6 oz/gal of Thinner 225 E: 231 g/l

    These are nominal values and may vary slightly with colour. Product contains VOC-exempt t-butyl acetate. Check local regulations regarding product usage

    Dry Temp. Resistance:Continuous: 82°C
    Non-Continuous: 104°C
    Primer:Self-priming
    Topcoats:Topcoat selection will depend on exposure
    Limitations:Epoxies lose gloss, discolour, and eventually chalk in sunlight exposure
    Flash Point:

    Part A: 21°C

    Part B: 33°C

    Shelf Life:

    Part A: 12 months at 24°C

    Part B: 24 months at 24°C

    Storage Temperature and Humidity:4°C-38°C
    0-95% Relative Humidity



    Drying Times


    Curing Schedule
    Surface TempDry to HandleDry to Topcoat MinimumMaximum Recoat Time
    -7°C36 Hours24 Hours45 Days
    2°C16 Hours2 Hours45 Days
    10°C10 Hours1 Hour30 Days
    24°C3 Hours30 Minutes30 Days
    32°C90 Minutes30 Minutes3 Days



    • Note: Minimum cure time, prior to placing in potable water, is 7 days
    • These times are based on a 50 microns dry film thickness per coat. Higher film thickness, insufficient ventilation or cooler temperatures will require longer cure times and could result in solvent entrapment and premature failure
    • While this product can tolerate excessive humidity during curing, check for blush or haze and remove, if present, by water washing before recoating
    • If the maximum recoat times have been exceeded, the surface must be abraded by sweep blasting or sanding prior to the application of additional coats
    • For force curing, contact Rawlins on Tech - 0113 2455450 (option 2) or [email protected] for specific requirements
    • For application and cure conditions below 1.6°C, dehumidify before, during, and after application to prevent ice formation on the surface
    • Do not apply to substrates with ice or ice crystal formation
    • Dehumidify or raise the temperature to eliminate ice on the substrate
    • Exposure to elevated temperatures (e.g. 26°C or greater) or sunlight can dramatically reduce the maximum recoat times



    Surface Preparation


    General

    • Steel: Remove any oil or grease from surface to be coated with clean rags soaked in Carboline Thinner 2, or toluol
    • Concrete: Do not apply coating unless concrete has cured at least 28 days @ 21°C and 50% RH or equivalent

    Steel

    • For immersion applications: Abrasive blast to a Near-White Metal Finish in accordance with SSPC-SP 10 and obtain a 2.5-4 mil blast profile
    • For non-immersion applications: Abrasive blast to a Commercial Finish in accordance with SSPC-SP 6 and obtain a 1½-2 mil (40-75 micron) blast profile for moderate to severe exposures. For mild environments, Hand Tool or Power Tool clean in accordance with SSPC-SP 2, SSPC-SP 3, or SSPC-SP 11 to produce a rust-scale free surface. For applications over damp surfaces, brush and roller is the preferred method

    Concrete:

    • Remove all loose, unsound concrete. Can be applied to damp concrete with no visible water present. Consult Rawlins for more specific recommendations



    Application Methods


    Product Information
    Mixing:

    Mix separately, then combine and mix in the following proportions (3:1 ratio):

    1 Gal. Kit

    • Part A: 0.75 gallon
    • Part B: 0.25 gallon

    4 Gal Kit

    • Part A: 3 gallons
    • Part B: 1 gallon
    Thinning:

    Thinning not normally required. May be thinned up to 6 oz/gal with Carboline exempt Thinner 225 E to maintain VOC. Maintain constant agitation to ensure consistency due to settling.

    Tip: If spraying is stopped for more than 10 minutes it is advisable to recirculate the material lines

    Pot Life:3 hours at 24°C and less at higher temperatures. Pot life ends when coating becomes too viscous to use
    Conventional Spray:Pressure pot equipped with dual regulators, 3/8” I.D. minimum material hose, 0.070” I.D. fluid tip and appropriate air cap
    Airless Spray:

    Pump Ratio: 30:1 (min.)

    GPM Output: 2.5 (min.)

    Material Hose: 3/8” I.D. (min.)

    Tip Size: 0.015-0.019”

    Output PSI: 2000-2500

    Brush and Roller:

    Multiple coats may be required to obtain desired appearance, recommended dry film thickness, and adequate hiding

    Avoid excessive re-brushing or re-rolling. For best results, tie-in within 10 minutes at 24°C. Use a short-nap synthetic roller cover with solvent resistant core



    Application Conditions


    Product Conditions
    ConditionMaterialSurfaceAmbientHumidity
    Minimum7°C-7°C-7°C0%
    Maximum32°C49°C38°C95%



    • Industry standards are for substrate temperatures to be above the dew point
    • Phenoline 311 Primer is unique in that it can tolerate damp substrates
    • Special thinning and application techniques may be required above or below normal conditions



    Health and Safety


    Clean Up

    • Use Thinner 2 or Acetone
    • In case of spillage, absorb and dispose of in accordance with local applicable regulations

    Safety

    • Read and follow all caution statements on this product data sheet and on the safety data sheets for this product and use personal protective equipment as directed
    • Employ normal workmanlike safety precautions

    Ventilation

    • When used in enclosed areas, thorough air circulation must be used during and after application until the coating is cured.
    • The ventilation system should be capable of preventing the solvent vapor concentration from reaching the lower explosion limit for the solvents used
    • User should test and monitor exposure levels to ensure all personnel are below guidelines
    • If not sure or if not able to monitor levels, use MSHA/NIOSH approved supplied air respirator

    Caution

    • This product contains flammable solvents. Keep away from sparks and open flames
    • All electrical equipment and installations should be made and rounded in accordance with applicable local regulations
    • In areas where explosion hazards exist workers should be required to use non-ferrous tools and wear conductive and non-sparking shoes
    • Refer to the product data sheet and safety data sheets in the attachments section above for further details
    Product Details
    0629A1NL

    Data sheet

    Manufacturer
    Carboline
    Water / Solvent Based
    Solvent
    For Use On
    Steel, Concrete
    Application Method
    Airless Spray, Conventional Spray, Brush, Roller
    Sheen
    Flat
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Two-pack
    Pack Size
    17L
    Mixing Ratio
    4:1 Ratio by volume(A to B)
    Dry to Handle (at 20°C)
    36 Hours
    Dry to Recoat (at 20°C)
    24 Hours
    Coverage
    754 ft²/gal at 1.0 mils (18.5 m²/l at 25 microns) - 251 ft²/gal at 3.0 mils (6.2 m²/l at 75 microns)
    Recommended Thinner/Cleaner
    Thinning is not required
    Compatible Topcoats
    Topcoat selection will depend on exposure
    Max. Application Temperature
    Material: 32°C - Surface: 49°C - Ambient: 38°C - Humidity: 95%
    Min. Application Temperature
    Material: 7°C - Surface: -7°C - Ambient: -7°C - Humidity: 0%
    Solids by Volume
    47% +/- 2%
    VOC
    0.04 lbs./gal (5 g/L)
    Shelf Life (from date of manufacture)
    Part A: 12 months at 76°F (24°C) - Part B: 24 months at 76°F (24°C)
    Dry for Topcoat (at +20°C)
    24°C: 30 Minutes - 32°C: 30 Minutes
    Recommended Dry Film Thickness
    1 - 3 mils (25 - 76 microns) Typical
    UN Number
    UN1263
    Pot Life
    3 hours at 24°C
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    Carboline Phenoline 311 Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    Carboline Thinner 2

    Carboline Thinner 2 is a thinner for use in industrial coatings.More Information Delivery Info

    Price £32.63 (ex. VAT)
    In Stock and Available for Delivery

    Carboline Thinner 225 E

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product.

    In stock

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery