Tor Torfab TP Etch Primer (Chromate Free)

    CR533

    We no longer stock this product; please contact our technical team on 0113 2455450 (option 2) or send a message to [email protected] where we will be happy to find an alternative product. See our metal primers page for more paints and coatings.

    Quantity
    Product not available
    This Product has been Discontinued

    Description

    Tor Torfab TP Etch Primer (Chromate Free) is a 2-part pre-treatment primer for non-ferrous metals such as aluminium, galvanising, copper, brass, etc, and is capable of being overcoated with a wide variety of single pack and two pack products. This Etch Primer has good coverage of up to 14 square metres per litre and is applied by spray (conventional or airless). Overcoat the primer after 4 hours (at 20ºC).

    Tor Torfab TP Etch Primer (Chromate Free) is an acid catalysed polyvinyl butyral type containing non toxic anti-corrosive pigment and extenders. Coloured yellow, it should be easier to spot which parts of a surface need to be overcoated.



    Features & Benefits


    • Pre-treatment primer for non-ferrous metals
      • Aluminium, galvanising, copper, brass, etc
    • Chromate-free
    • 2 part, consisting of base and activator
    • Apply by conventional or airless spray
    • Touch dry in just 5 minutes - recoat after 4 hours (at 20ºC)
    • Can be overcoated with a wide variety of single pack and two pack products
    • Yellow colour - easy to see to overcoat
    • Good coverage - up to 14 square metres per litre
    • 8 hour pot life
    • Refer below for more product data, including application and preparation instructions



    Product Information


    Product referenceCR533
    Volume solids7%
    Typical thickness7 microns dft from 100 microns wet
    Theoretical coverage14 square metres per litre
    Practical coverage10 square metres per litre
    Colour rangeYellow



    Surface Preparation


    Non-ferrous metals such as aluminium, galvanised, copper, brass etc. – surfaces must be degreased until no further evidence on “white swab”.



    Application Details


    Mix ratio1:1 by volume
    Method of applicationSpray (conventional or airless). Small areas may be brushed.
    ThinnerTor TH80 (where necessary)
    CleanerTor TH80 for cleaning equipment
    Pot Life8 hours



    Drying Times


    Substrate TemperatureTouch DryHard DryOvercoating Interval
       MinimumMaximum
    20ºC5 mins30 mins4 hours28 days

    Note: Drying/curing times will be shortened by higher temperatures and lengthened by lower temperatures



    Storage and Handling


     

    Storage

    Store the closed containers in a store room which is either in a safe place or is a fire resisting structure. The storage and conditions must meet the statutory requirements of The Highly Flammable Liquids and Petroleum Gases Regulations 1972.

    Flash point

    • Below 22ºC



    Limitations


    1. Do not exceed normal film thickness
    2. Do not use material that has exceeded its 8 hours pot life

    Product Details
    CR533

    Data sheet

    Manufacturer
    Tor
    Water / Solvent Based
    Solvent
    For Use On
    Non-ferrous metals, aluminium, Galvanized Steel, copper, brass
    Application Method
    Spray, brush
    Sheen
    Matt
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Two-pack
    Pack Size
    10L
    Solvent
    Acid catalysed polyvinyl butyral type containing non toxic anti-corrosive pigment and extenders.
    Mixing Ratio
    1:1 by volume
    Key Features
    Pre-treatment etch primer for non-ferrous metals
    Touch Dry (at 20°C)
    5 mins
    Dry to Handle (at 20°C)
    -
    Dry to Recoat (at 20°C)
    4 hours
    Fully Cured (at 20°C)
    30 mins
    Pot Life (at 20°C)
    8 hours
    Coverage
    Theoretical: 14 square metres per litre; Practical: 10 square metres per litre
    Recommended Thinner/Cleaner
    Tor TH80
    Unit Contents
    -
    Compatible Primers
    -
    Compatible Topcoats
    -
    Max. Application Temperature
    -
    Min. Application Temperature
    -
    Density
    -
    Solids by Volume
    7%
    Heat Resistance (up-to)
    -
    VOC
    -
    Shelf Life (Once Opened)
    -
    UN Number
    UN 1263, UN 1993
    Brand
    Tor Coatings

    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    Tor Torfab TP Etch Primer (Chromate Free) is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery