Tor QD High Build Phosphate Primer

AK636

Tor QD High Build Phosphate Primer, a quick drying high build anti-corrosive primer for blast cleaned or mechanically cleaned mild steel. Applied by spraying, the primer is touch dry in 1 hour and hard dry in 4 hours.

  • Anti-corrosion protection for cleaned mild steel
  • An alkyd resin binder with zinc phosphate anti-corrosive pigment, together with inert inorganic pigments and thinned with a blend of xylene and aromatic hydrocarbon solvents
  • Up to 6 square metres per litre
  • Not suitable for overcoating with 2 pack products
  • Refer below for more product information and instructions for application and preparation

Colour
Size
Finish
£37.10
VAT excluded

£44.52 Tax incl.
Quantity

Description

Tor QD High Build Phosphate Primer is a quick drying high build anti-corrosive primer for blast cleaned or mechanically cleaned mild steel. Applied by spraying, the primer is touch dry in 1 hour and hard dry in 4 hours.



Features & Benefits


  • Anti-corrosion primer for mild steel
  • Quick drying - touch dry in 1 hour, hard dry in 4 hours
  • Applied by spray
    • Smaller areas can be applied by brush
    • Brush application will only produce approximately half the recommended film thickness
  • Not suitable for overcoating with 2 pack products
  • Theoretical coverage of up to 6 square metres per litre
  • Refer below for more product information and instructions for application and preparation



Product Information


An alkyd resin binder with zinc phosphate anti-corrosive pigment, together with inert inorganic pigments and thinned with a blend of xylene and aromatic hydrocarbon solvents.

Product reference AK636
Volume solids 45%
Typical thickness 75 microns dft from 167 microns wet
Theoretical coverage 6 square metres per litre
Practical coverage Reduce theoretical coverage by up to 20%
Colour range Grey
VOC content EU limit value for this product (cat A/i): 500 g/l . This product contains max 500 g/l VOC



Surface Preparation


Steel:

Grit blast to BS4232, 2nd Quality (SA 2.5 Swedish Standard) with a blast profile of 50-75 microns to remove all scale, rust, old paint and contaminants.

Minimum – chip scrape and mechanically wire brush to Swedish Standard ST2 for mechanically cleaned steel.



Application Details


Mix ratio N/A
Method of application Airless spray (tip size 0.019”-0.021” and 2000-2400 psi atomising pressure) Small areas can be brushed, two coats may be necessary to achieve the dry film thickness quoted.
Thinner Thinning may render product VOC non-compliant.
Cleaner Tor TH25
Pot Life N/A



Drying Times


Substrate Temperature Touch Dry Hard Dry Overcoating Interval
      Minimum Maximum
20ºC 1 hour 4 hours 4 hours 3 months

Note: Drying/curing times will be shortened by higher temperatures and lengthened by lower temperatures



Storage and Handling


 

Flash Point

  • 23ºC



Limitations


Not suitable for overcoating with 2 pack products.

Brush application will only produce approximately half the recommended film thickness.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
AK636

Data sheet

Manufacturer
Tor
Parts
1
Base Type
Solvent
Mixing Ratio
-
Suitable Substrates
Blast cleaned or mechanically cleaned mild steel
Key Features
Anti-corrosion primer
Application
Theoretical coverage: 6 square metres per litre; Practical coverage: Reduce theoretical coverage by up to 20%
Touch Dry (at 20°C)
1 hour
Dry to Handle (at 20°C)
-
Dry to Recoat (at 20°C)
4 hours
Fully Cured (at 20°C)
4 hours
Pot Life (at 20°C)
-
Coverage
Theoretical coverage: 6 square metres per litre; Practical coverage: Reduce theoretical coverage by up to 20%
Recommended Thinner/Cleaner
Tor TH25
Unit Contents
-
Compatible Primers
-
Compatible Topcoats
-
Max. Application Temperature
-
Min. Application Temperature
-
Density
-
Solids by Volume
45%
Heat Resistance (up-to)
-
VOC
500 g/l VOC
Shelf Life (Once Opened)
-
UN Number
UN 1263
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Tor HF Aromatic Thinners

Tor HF Aromatic Thinners (TH025), high flash point substitutes for Xylene used for thinning chlorinated rubber paints, etc, and for the cleaning of the same materials from application equipment.

Price £34.70
In stock
16 other products in the same category:

PPG Sigma Etch

PPG Sigma Etch, a phosphoric acid-based etch solution for treating new, unweathered galvanized surfaces, where blasting or abrasion is not possible, prior to painting. Changes color on application from blue to black to indicate the effectiveness of primary pre-treatment Meets the requirements of British Rail's 'T-wash' solution May be...

Price £29.05
In stock

International Interprime 306

International Interprime 306 is a single component, fast drying, high build alkyd primer used as a shop applied post-fabrication primer specifically designed for a blast, fabricate and prime steel production route, and where fast drying and rapid handling properties are required. Coverage Calculator

Price £42.13
In stock

Sherwin-Williams Macropoxy M111

Sherwin-Williams Macropoxy M111 is a 2-pack epoxy zinc phosphate primer for application to surfaces which have been prepared by wet abrasive blasting. It may also be applied to grit blasted surfaces and for surfaces prepared by UHP water blasting where existing blast profile is exposed.  Coverage Calculator

Price £79.15
In stock

International Intergard 214

International Intergard 214 is a two component epoxy sealer coat pigmented with aluminium flake for the effective penetration and sealing of thermally sprayed aluminium coatings to eliminate porosity. Has specification approval for UK Department of Transport Item No.159. Coverage Calculator

Price £71.82
In stock

Coo-Var Water Based All Metals Primer

Coo-Var Water Based All Metals Primer is a water thinnable acrylic metals primer which has very good anti-corrosive properties. It is low odour and easy to apply to most metals. Product Features Water based primer Interior and exterior Suitable Surfaces: Most Metals Inc. Iron, Steel, Aluminium, Brass, Copper Finish: Matt Application:...

Price £13.19
In stock

International Intercure 200HS

A fast drying reputation isn't all International Intercure 200HS is renowned for. Complete with MIO, this fast cure anti-corrosive primer/intermediate with added barrier protection, can improve your productivity and lower your solvent emissions. Coverage Calculator

Price £386.64
In stock

International Intergard 400

International Intergard 400 is a high build, two component epoxy, pigmented with lamellar micaceous iron oxide for enhanced corrosion resistance and improved overcoating properties after ageing. Coverage Calculator

Price £227.14
In stock

Jotun Muki AC

A one component waterborne primer from Jotun that is a shop primer designed for high welding and cutting speed, giving reduced weld porosity and back burning. It is fast drying making it suitable for stacking shortly after application. Jotun Muki AC is a one component physically drying waterborne acrylic coating. Coverage Calculator

Price £147.87
In stock

Rust-Oleum 6400 Fast Drying Shopprimer

Rust-Oleum 6400 Fast Drying Shopprimer is a fast drying, solvent based, anti-corrosive primer for temporary metal protection intended as the first coat in shop coating applications and provides the required basic protection following metal fabrication and assembly operations. Excellent adhesion to metal Ideal for spray application...

Price £23.50
In stock

Jotun Penguard Primer

Jotun Penguard Primer is a two component polyamide cured high molecular weight epoxy coating designed as a primer for new construction. It can be used as a primer as a part of a complete system in atmospheric and immersed environments. Suitable for properly prepared carbon steel, stainless steel, aluminium, concrete, galvanised steel, shop...

Price £36.59
In stock

PPG AquaCover 20

PPG AquaCover 20 (also known as Sigma Aquacover 20) is a one-component waterborne, high-build zinc phosphate primer/coating, based on acrylic dispersion. It can be overcoated with most waterborne acrylics, solvent-borne epoxy coatings and alkyd paints, as well as certain solvent-borne, two-component products. Useful for when solvents are...

Price £64.35
In stock

Carboline Carboguard 888 MIO

A low temperature and rapid curing primer/finish with an extended recoat window that provides excellent corrosion resistance as a primer, intermediate or finish coat on to steel. Top Features Low-temperature characteristics Rapid handling Low yellowing VOC compliant

Price £249.00
In stock

Cromadex AQ58 One Pack Waterbased Acrylic Primer

Cromadex AQ58 One Pack Waterbased Acrylic Primer is a one pack waterbased acrylic primer for use over a wide range of substrates. Cromadex AQ58 is available in grey and white as standard, it can also be tinted to ensure complete coverage even on difficult lead free colours. Life expectancy of up to 3 years in a C2 external environment when...

Price £76.15
In stock

Carboline Carbomastic 18 FC

This epoxy is a fast-curing, heavy-duty, high-build anti-corrosive coating with a broad and versatile list of uses in marine and other corrosive environments. It is an excellent choice for the protection of ship hull exteriors, underwater and ballast tanks. Top Features Excellent immersion performance in water Suitable as a rust...

Price £62.25
In stock

Nullifire PM021 General Purpose Epoxy Primer

Nullifire PM021 General Purpose Epoxy Primer is a two-components epoxy polyamide primer with excellent resistance to salts, water and alkalies, and with very good resistance to mild acids and solvents. 

Price £265.07
In stock

International Intergard 307

International Intergard 307 is a two pack epoxy zinc phosphate primer, primarily formulated to meet the requirements of the UK Highways Agency specification. International Intergard 307 is intended to be used as a primer or blast primer under high build epoxy coating schemes for new construction. Coverage Calculator

Price £67.90
In stock