Tor Quick Drying Red Oxide Primer prepares steel components and fabrications for overcoating with compatible topcoats, dry and ready in just 1 hour. Can be applied by brush, short pile roller or airless spray.
An alkyd binder pigmented with inert inorganic pigments and thinned with an aromatic hydrocarbon solvent blend
Not suitable for use in water immersed conditions or for overcoating with two pack materials
Apply by brush, short pile roller or airless spray, with good coverage with up to 10 square metres per litre
Refer below for more product information, preparation and application instructions
Use Tor Quick Drying Red Oxide Primer to prepare steel components and fabrications for overcoating, dry in just 1 hour. Can be applied by brush, short pile roller or airless spray.
Features & Benefits
Not suitable for use in water immersed conditions or for overcoating with two pack materials
Touch dry in 30 minutes - can be overcoated after just 1 hour
Apply by brush, short pile roller or airless spray
Good coverage with up to 10 square metres per litre
Refer below for more product information, preparation and application instructions
Product Information
An alkyd binder pigmented with inert inorganic pigments and thinned with an aromatic hydrocarbon solvent blend.
Product reference
AK618
Volume solids
47%
Typical thickness
47 microns dft from 100 microns wet
Theoretical coverage
10 square metres per litre
Practical coverage
Reduce theoretical coverage by up to 20%
VOC content
EU limit value for this product (cat A/i): 500 g/l . This product contains max 500 g/l VOC
Surface Preparation
Steel:
Grit blast to BS4232 2nd quality (Sa 2.5 Swedish Standard) with a blast profile of between 50-75 microns to remove all scale, rust, old paint and contaminants.
Minimum:
Should be mechanically cleaned to Swedish Standard ST2 for mechanically cleaned steel.
Application Details
Mix ratio
N/A
Method of application
Brush, short pile roller or airless spray (tip size 0.019” to 0.021” and 2000 psi atomising pressure)
Note: Drying/curing times will be shortened by higher temperatures and lengthened by lower temperatures
Storage and Handling
Flammable. Keep away from heat and flames. Store in tightly closed original container in a dry, cool and well ventilated place. Keep in original container. Avoid contact with oxidising agents.
Flash point
Above 23°C
Shelf life
2 years in unopened containers
Limitations
Not suitable for use in water immersed conditions or for overcoating with two pack materials.
Avoid skin and eye contact i.e. wear gloves, goggles, etc
Ensure good ventilation, mechanical if necessary
Store and use away from heat and flame
Do not eat or smoke in the vicinity of work
Wash hands before eating
Refer to supply container for additional warning labels
Product Details
4092-515329
Data sheet
Manufacturer
Tor Coatings
Water / Solvent Based
Solvent
For Use On
Steel
Application Method
Brush, roller, spray
Sheen
Matt
Colour
Standard / Ready Mixed
Single, Two or Three Pack
Single
Pack Size
5L, 20L
Parts
1
Solvent
An alkyd binder pigmented with inert inorganic pigments and thinned with an aromatic hydrocarbon solvent blend.
Mixing Ratio
-
Key Features
For steel components and fabrications, ready to overcoat in just 1 hour.
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
Tor Quick Drying Red Oxide Primer is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
We no longer stock this product, but can recommend Tor QD Thinner as a great alternative. Please note: it is important to check that any alternative product is suitable for your requirements, as our suggestion is given in good faith but without warranty. If you are in any doubt please first contact our technical team on 0113 2455450 (option...
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...