Rust-Oleum 9170/9180 Epoxy Metal Primer

9170.5

Rust-Oleum 9170/9180 Epoxy Metal Primer is a fast drying metal primer based on two-component epoxy resin offering extra protection against corrosion on bare or blasted metal, also ideal for galvanised metal under severe conditions.

  • High build primer for optimal opacity with topcoat 9100
  • Touch dry after just 1 hour
  • Contains a high amount of rust inhibitors
  • Easy to apply by brush, roller or spray
  • Easy 1:1 mixing ratio
Colour
Size
Finish
£108.43
VAT excluded

£130.12 Tax incl.
Quantity

Description

Rust-Oleum 9170/9180 Epoxy Metal Primer

Rust-Oleum 9170/9180 Epoxy Metal Primer is a fast drying metal primer based on two-component epoxy resin offering extra protection against corrosion on bare or blasted metal. Rust-Oleum 9170/9180 Epoxy Metal Primer is the best fast drying primer for bare and galvanised metal under severe conditions.

Rust-Oleum 9170/9180 Epoxy Metal Primer is designed for application on bare or blasted metal and can be recoated with Rust-Oleum 9100 topcoats, offering the appropriate protection against strong chemicals, acids, alkalis and solvents; frequent product spillage and frequent chemical cleaning; high humidity and moist conditions.

Features & Benefits

  • Fast drying
  • High film build; up to 100 microns dry in one coat is possible
  • Easy to apply
  • Excellent adhesion
  • Easy mixing (1:1 ratio)

Technical Data

  • Density: 1,5
  • Gloss Level: Matt
  • Corrosion Class: C4 high protection
  • Solids content in volume: 52 %
  • Heat Resistance: 150°C (dry heat)
  • Mixing Ratio: 1 : 1 by volume

Drying Times At 20°C/RH 50%

  • Touch dry: 1 hour
  • Dry to handle: 2 hours
  • Dry to recoat: After 16 hours
  • Fully cured: 8 days
  • Pot Life: 8 hours for a 5 ltr. mix at 20°C
  • Induction Time: 30 minutes

Theoretical Consumption

7 m²/l

Practical Consumption

Practical coverage depends on many factors such as porosity and roughness of the substrate and material losses during application.

Application Conditions

Temperature of air and substrate between 5 and 35°C and relative humidity below 85%. The substrate temperature must be at least 3°C above dew point.

Please note: This product is recoatable with 9100 Epoxy topcoat and if good U.V. resistance is required, Rust-O-Thane Polyurethane Topcoat 9600 should be applied.

Please contact Rawlins Paints' Technical Support Team on 0113 2455450 for more information.

It is your responsibility to read the Product Data Sheets (available below) before you place an order and prior to application of the product. The content of this website is our best recommendation and is not advice. Coverage rates quoted are approximate, you agree that coverage depends on the condition of the substrate, surface absorption, texture and application method. We ALWAYS recommend a trial area is coated to ensure the product meets your requirements before use.

Product Details
9170.5

Data sheet

Base Type
Based on two-component epoxy
Mixing Ratio
1 : 1 by volume
Application
Brush, Roller, Spray
Dry to Handle (at 20°C)
2 Hours
Dry to Recoat (at 20°C)
After 16 hours
Fully Cured (at 20°C)
8 Days
Pot Life (at 20°C)
8 hours for a 5 ltr. mix at 20°C
Coverage
7m² per litre
Recommended Thinner/Cleaner
RUST-OLEUM Thinner 160.
Max. Application Temperature
35°C
Min. Application Temperature
5°C
Solids by Volume
52 %
Heat Resistance (up-to)
150°C (dry heat)
VOC
421 g/l
Shelf Life (from date of manufacture)
5 years from date of production in unopened cans, if stored in dry, well ventilated areas, not in direct sunlight at temperatures between 5° and 35°C.
Touch Dry
1 Hour
Recommended Dry Film Thickness
75 µm
Recommended Wet Film Thickness
150 µm
UN Number (Activator)
Not regulated
UN Number (Base)
Not regulated
Attachments
Download


Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


Be the first to ask a question about this product!


Question about the product

* Required fields
(read)
Send
You might also like

Rust-Oleum Thinner 160

Rust-Oleum Thinner 160 is a specially formulated blend of solvents designed to mix with Rust-Oleum's 1085 Galva Zinc, 9100 High Performance Epoxy and B95 Flexible Epoxy to create an optimal consistency for application whether it be for Brush, Roller or Spray. Can also be used for the cleaning of some surfaces or equipment. Strong dilution...

Price £13.04
In stock

Rust-Oleum 9100 Winter Grade Epoxy

Rust-Oleum 9100 Winter Grade Epoxy coating for application at temperatures down to 0°C. Two-pack, glossy epoxy coating for metal, walls and floors. The most efficient epoxy system providing a very hard coating with high layer thickness for lasting results even with a single coat application. Single coat application directly over rusted...

Price £97.58
In stock

Rust-Oleum 9100 High Performance Epoxy

Rust-Oleum 9100 High Performance Epoxy is a two-pack, glossy epoxy for metal, walls and floors. It is the most efficient epoxy system providing a very hard coating with high layer thickness giving lasting results with even a single coat application. 

Price £98.77
In stock

Rust-Oleum 9100 High Solids Epoxy

Rust-Oleum 9100 High Solids Epoxy is a higher solids, better coverage and lower VOC content product than the standard 9100 Epoxy. Two-pack, glossy epoxy coating for metal, walls and floors. The most efficient epoxy system providing a very hard coating with high layer thickness for lasting results even with a single coat application. Single...

Price £108.16
In stock
16 other products in the same category:

Tor Torfab TP Etch Primer (Chromate Free)

Tor Torfab TP Etch Primer (Chromate Free), a 2-part pre-treatment primer for non-ferrous metals such as aluminium, galvanising, copper, brass, etc. The primer is capable of being overcoated with a wide variety of single pack and two pack products and be overcoated after 4 hours (at 20ºC). Good coverage - up to 14 square metres per litre...

Price £85.99
In stock

Britannia Zinc Phosphate Metal Primer

A metal primer for ferrous metals such as iron and steel that offers sound anti-corrosion properties and superb capacity and coverage. Can be used over existing paintwork. Examples of Use Bridges Metal artwork Metal trusses Warehouses Factories

Price £27.34
In stock

Jotun Penguard Midcoat

Jotun Penguard Midcoat is suitable for structural steel and piping to be exposed to corrosive environments up to very high. Recommended for offshore environments, refineries, power plants, bridges, buildings and mining equipment. A high solids, high build product designed as a mid coat in systems for new construction in atmospheric...

Price £147.42
In stock

Teamac Micaceous Iron Oxide

Teamac Micaceous Iron Oxide, is a high build coating for the protection of structural steelwork against corrosion.  It can be used as either an intermediate, or finish coat.  For use on cranes, transmission towers, bridges, lamp posts, railings etc.  Its thick anti-corrosive film is extremely effective in prolonging the life of these types...

Price £49.76
In stock

International Intergard 405

International Intergard 405 is a two component epoxy sealer coat, pigmented with micaceous iron oxide. Formulated on proprietary polymer technology, which provides rapid cure and overcoating, even at low temperatures.

Price £208.50
In stock

PPG AquaCover 400

PPG AquaCover 400 (also known as Sigma Aquacover 400) is a two-component, polyamine-cured, waterborne epoxy coating for steel structures in atmospheric exposure, touch dry in 90 minutes. Also suitable for concrete floors. Top Features Particularly suitable when solvents are not permitted because of health and safety reasons Free from...

Price £98.20
In stock

Jotun Penguard Express MIO

Jotun Penguard Express MIO is a two component amine cured epoxy coating that is a fast drying, micaceous iron oxide (MIO) pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in...

Price £42.82
In stock

Hydron Nu-Steel TP Etch Primer

Nu-Steel® TP Etch Primer is a two pack primer giving excellent adhesion to metals prior to subsequent paint systems.  Advantages Up to 8 years protection. Available in yellow or grey. 15m²/Litre approx. coverage rate. 12-month shelf life.

Price £279.50
In stock

Sherwin-Williams Transgard TG116

Sherwin-Williams Transgard TG116 is a two pack epoxy undercoat for abraded surfaces. It is used for application onto suitably primed surfaces, as an undercoat for use under suitable high performance finishes. 

Price £68.36
In stock

PPG SigmaCover 1500

PPG SigmaCover 1500, a two-component, surface-tolerant, solvent-free, polyamine-cured epoxy primer/buildcoat for long-term protection of steel structures. Excellent corrosion resistance, with good flow and wetting properties Compatible with various aged coatings, like aged alkyd, epoxy and polyurethane Reduces explosion risk and fire...

Price £98.76
In stock

International Intercure 324

International Intercure 324 is a two component, high solids, low VOC, epoxy zinc phosphate/micaceous iron oxide primer offering excellent barrier protection, low temperature cure and rapid overcoating properties. Pigmented with zinc phosphate anti-corrosive pigment to comply with the requirements of BS5493:1977.

Price £85.76
In stock

Tor HB Micaceous Iron Oxide

Tor HB Micaceous Iron Oxide, a high build anti-corrosive coating for structural steelwork on structures such as cranes, bridges, gantries, tanks, etc. Apply by spray or brush Brush application will only achieve 45 to 70 microns dry film thickness 2 colours available Touch dry in 2 hours Overcoat after 16 hours Micaceous oxide of...

Price £36.47
In stock

PPG Sigma Etch

PPG Sigma Etch, a phosphoric acid-based etch solution for treating new, unweathered galvanized surfaces, where blasting or abrasion is not possible, prior to painting. Changes color on application from blue to black to indicate the effectiveness of primary pre-treatment Meets the requirements of British Rail's 'T-wash' solution May be...

Price £29.05
In stock

Jotun Penguard Express ZP

Jotun Penguard Express ZP is a two component amine cured epoxy coating that is a fast drying, zinc phosphate pigmented, high solids, high build product. Specially designed for new construction where fast dry to handle and over coating times are required. Can be used as a primer, mid coat, finish coat or as a single coat system in atmospheric...

Price £40.28
In stock

Teamac Rapidry HB Zinc Phosphate Primer

Teamac Rapidry HB Zinc Phosphate Primer, is a high build, high performance quick drying metal primer.  It has excellent anti-corrosive properties. Anti-corrosive Rapid drying Use on iron Use on Steel Semi-Matt Finish Click to jump down to Technical Data Coverage Calculator

Price £15.04
In stock

PPG AquaCover 20

PPG AquaCover 20 (also known as Sigma Aquacover 20) is a one-component waterborne, high-build zinc phosphate primer/coating, based on acrylic dispersion. It can be overcoated with most waterborne acrylics, solvent-borne epoxy coatings and alkyd paints, as well as certain solvent-borne, two-component products. Useful for when solvents are...

Price £64.35
In stock