HMG Ferrozinc Rust Converter is a high performance water-based rust converter, ideal for application to areas difficult to shot-blast or where total removal of rust is not possible. Also suitable for surfaces difficult to dry due to existing moisture.
Easily applied single pack material
Changes colour to show rust has been neutralised
Excellent long term conversion properties
Brush application
Hard dry in 1 hour at 20°C
Suitable for structural steel, fences, iron railings, guttering, external ferrous metals, vehicles, machinery and marine situations
Compatible with most coating systems including water/oil based, chlorinated rubber and epoxy systems
Offers a far superior performance than conventional coatings applied to slightly rusted surfaces
To be used after wire brushing to remove surface rust
A dramatic colour change from white to black shows that rust has been effectively neutralised
Product should not be used over oil/grease contamination or existing paint as this will render the product ineffective
Do not apply during wet weather
For professional use only
Manufactured under the auspices of an ISO 9001 management system
Product Specification
Technical Data
VOC Content:
30g/L
Storage Conditions:
Store between 5°C - 25°C. When not in use, cans must be kept sealed.
Pot Life:
N/A
Dry Film Thickness:
20 μm
Wet Film Thickness:
30 μm
Coverage:
20m2/L at 20 microns
Drying Times
Drying Times At 20°C
Touch Dry:
20-30 minutes
Hard Dry:
60 minutes
Full Dry:
2-3 days
Surface Preparation
Ensure surfaces are clean, dry and free from grease, oils, dust and other contamination prior to application
Substrate temperature should be 5⁰C or above for application and during cure, and a minimum of 3⁰C above the dew point
Adequate dry air ventilation should be supplied during drying
Read and follow the safety data sheet, product data sheet (see section above) and label instructions
High pressure wash to remove all loose debris and other contamination
Thoroughly clean and degrease using suitable HMG Prep Clean 2801, HMG 2802 or HMG 2804 until surface is clean and free from all deposits (grease, oil, silicone)
Heavily rusted areas to scraped, wire brushed or mechanically prepared to remove all loose material
Failure to degrease areas to be treated could slow down or stop conversion process
Stir all paints thoroughly before use
Always use the same batch number on the same job
Check colour & sheen
Filter the product immediately before use
Reduce emissions and maintain quality by replacing tin lid after use
Application
Apply by brush to affected areas, applying light coat
Avoid coating non rusted areas where possible
Application and use should always conform with the codes of practice described in BS 6150 and BS 5493
Substrates
HMG Ferrozinc is suitable for use on wire brushed or mechanically abraded metal surfaces which are free from heavy rust scale, grease and dirt
Health & Safety
Refer to SDS and tin label prior to use.
Suitable respiratory equipment should be worn when spraying.
Contaminated rags, spray booth filters or other substrates should be segregated from other chemical waste, soaked with water or disposed of in a non-combustible container with tight fitting lid.
Product Details
4434-1004757
Data sheet
Manufacturer
HMG Paints Limited
Interior / Exterior Use
Exterior Use
Water / Solvent Based
Water
For Use On
Structural Steel Fences Iron Railings Guttering Ferrous Metals Vehicles Machinery Marine Applications Metal Substrates
Application Method
Brush
Sheen
Matt
Colour
Clear
VOC Levels
Ultra-Low (5-49 g/l)
Single, Two or Three Pack
Single
Pack Size
250ml 1L 5L
Mixing Ratio
Ready for use
Touch Dry (at 20°C)
20 - 30 minutes
Dry to Handle (at 20°C)
60 minutes
Dry to Recoat (at 20°C)
After 2 - 3 hours
Fully Cured (at 20°C)
2 - 3 hours
Coverage
20m²/L
Density
1.4 g/cm³ at 20°C
VOC
30g/L
Shelf Life (from date of manufacture)
12 months from delivery date in original sealed containers
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Ferrozinc Rust Converter is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
HMG Prep Clean 2802 is a fast evaporating, strong Preparatory Cleaning solvent for the heavy duty degreasing of substrates.Used in many applications For use on bare surfaces onlyMore Information Delivery Info
HMG Prep Clean 2804 is a water based preparatory Cleaner for the degreasing of substrates.Used in many applications For use on bare surfaces onlyMore Information Delivery Info
HMG Prep Clean 2801 is a slow evaporating, mild preparatory cleaning solvent for the degreasing of substrates.Used in many applications Anti-static For use on bare surfaces onlyMore Information Delivery Info
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...