HMG A1242 Undercoat

    PRIA1242
    HMG4438

    HMG A1242 Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties.

    • Suitable for large areas due to its ease of application and long wet edge time.

    Colour
    Size
    Finish
    £38.22(ex. VAT)
    £45.86 (inc. VAT)
    Quantity
    Please choose your colour
    Available for Delivery (See Delivery Options Below)

    Description

    HMG A1242 Undercoat is a 1K alkyd/polyurethane undercoat with superior brushing qualities and excellent obliteration properties.



    Click To Jump To Section:




    Features & Benefits


    • Suitable for large areas due to its ease of application and long wet edge time.



    Product Specification


    Technical Data
    HMG A1242 Undercoat
    Volume Solids:75.8%
    VOC Content:0.400kgs/ltr
    SG:-
    Viscosity:400 mPas
    Density:1.489 g/cm³
    Storage Conditions:Store between 5°C - 25°C. When not in use, cans must be kept sealed.
    Shelf Life:12 months from delivery date in original sealed containers.
    Pot Life:-
    Flash Point:37°C



    Film Thickness Range And Coverage


    Product Data
     Dry Film ThicknessWet Film Thickness
    Compliant Spray Gun:55 μm100 μm
    Brush:55 μm100 μm



    Coverage: 12 square metres per Litre @ 55 microns dft (theoretical).

    • HMG technical data sheets indicate a dry film thickness that will be achieved when applying a particular wet film thickness.
    • These values are a guide only and are not to be used as specifications.
    • Film thickness will vary depending on actual use and specification.
    • Great care should be taken to achieve the dft stated in the agreed specification and to avoid areas of excessively low or high thickness.



    Drying Times


    Drying Times At 20°C
    Touch Dry:3 hours
    Fully Cured:16 hours



    Surface Preparation


    • Ensure surfaces to be coated are dry and must be cleaned using the appropriate HMG product to remove all traces of contaminants.
    • Read and follow the safety data sheet, product data sheet and label instructions.
    • Stir all paints thoroughly before use.
    • Always use the same batch number on the same job.
    • Check colour & sheen.
    • Filter the product immediately before use.
    • Reduce emissions and maintain quality by replacing tin lid after use.



    Application Methods


    Technical Data
    Compliant Spray GunBrush
    Mixing Ratio:Base: 10Ready for use
    Thinner: 1-
    Thinner Options:Thinner 2612Thinner 2612
    Viscosity:25 - 35 seconds DIN4-
    Spray Gun Setup:1.8-
    Number Of Coats (Guide Only):2 full coats2 coats
    Flash Off:15 minutes between coats-



    For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]



    Product Notes


    Information On Basic Physical And Chemical Properties
    HMG A1242 Undercoat
    Form:According to product specification
    Colour:According to product specification
    Odour:Characteristic
    Odour Threshold:Not determined
    pH-value 20°C:Not determined
    Melting point/freezing point:Undetermined
    Initial boiling point and boiling range:137°C
    Flash Point:37°C
    Flammability (solid, gas):Not applicable
    Ignition temperature:200°C
    Decomposition temperature:Not determined.
    Auto-ignition temperature:Product is not selfigniting.
    Explosive properties:"Product is not explosive. However, formation of explosive air vapour mixtures are possible."
    Explosion limits: Lower:0.6 Vol %
    Explosion limits: Upper:7 Vol %
    Vapour pressure at 20°C:Not determined
    Density at 20°C:1.489 g/cm³
    Relative density:Not determined
    Vapour density:Not determined
    Evaporation rate:Not determined
    Solubility in / Miscibility with water:NOT MISCIBLE
    Partition coefficient: n-octanol/water:Not determined
    Viscosity: Dynamic at 20°C:400 mPas
    Viscosity: Kinematic:Not determined
    Solvent content: Organic solvents:23.9%
    Solids content:75.8%



    Health & Safety


    • Refer to the safety data sheet in the attachments section above and tin label prior to use.
    • Suitable respiratory equipment should be worn when spraying.

    Click to go back to the top of the page

    Product Details
    4438-689523

    Data sheet

    Manufacturer
    HMG Paints Limited
    Water / Solvent Based
    Solvent
    For Use On
    Metal
    Application Method
    Brush, spray
    Sheen
    Matt
    Colour
    Standard / Ready Mixed
    Single, Two or Three Pack
    Single
    Pack Size
    2.5L, 5L
    Mixing Ratio
    Base: 10 - Thinner: 1
    Touch Dry (at 20°C)
    3 hours
    Fully Cured (at 20°C)
    16 hours
    Recommended Thinner/Cleaner
    Thinner 2612
    Density
    1.489 g/cm³
    Solids by Volume
    75.8%
    Heat Resistance (up-to)
    80°C
    Shelf Life (from date of manufacture)
    12 months from delivery date in original sealed containers
    Recommended Dry Film Thickness
    55 μm
    Recommended Wet Film Thickness
    100 μm
    UN Number
    UN1263
    Base Type
    Solvent-Based
    Suitable For Use On
    Metal
    Finish
    Matt
    Application Method
    Brush
    Application Method
    Spray
    Product Usage Type
    Undercoat
    Colour Family
    Cream
    Colour Family
    White
    Attachments
    Download


    Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.


    Be the first to ask a question about this product!


    Question about the product

    * Required fields
    (read)
    Send

    IMPORTANT SHIPPING & DELIVERY INFORMATION

    HMG A1242 Undercoat is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.

    Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.

    Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.

    All delivery costs below are excluding VAT


    You might also like

    HMG Thinner 2612

    HMG Thinner 2612 is a slow thinner.For use with compatible HMG systems.More Information Delivery Info

    Price £11.22 (ex. VAT)
    In Stock and Available for Delivery

    Surface Preparation Kits for Steel

    These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...

    Price £21.53 (ex. VAT)
    In Stock and Available for Delivery