HMG Thinner 2691
HMG Thinner 2691 is a thinner for use in various applications.For use with compatible HMG systems.More Information Delivery Info
£13.21 (incl. VAT)
£11.01 (ex. VAT)
HMG Epiprime is a zinc phosphate 2K epoxy primer offering excellent adhesion.
This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:
2-Pack System Details | |||||
---|---|---|---|---|---|
Base (Part 1) | HMG Epiprime | ||||
Activator (Part 2) | Option 1: HMG Hardener 9058 Standard | ||||
Option 2: HMG Hardener 9060 Rapid Cure |
HMG Epiprime is a zinc phosphate 2K epoxy primer offering excellent adhesion.
Please note this product is one part of a two-pack system which MUST be purchased/used together with HMG Hardener 9058 Standard or HMG Hardener 9060 Rapid Cure.
Technical Data | ||||||
---|---|---|---|---|---|---|
Epiprime White | Epiprime Colours | |||||
Volume Solids: | 71.1% | 65.7% | ||||
VOC Content: | 0.530kgs/ltrl | 0.530kgs/ltr | ||||
SG: | - | - | ||||
Viscosity: | 220 mPas | 300 mPas | ||||
Density: | 1.487 g/cm³ | 1.281 g/cm³ | ||||
Storage Conditions: | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | Store between 5°C - 25°C. When not in use, cans must be kept sealed. | ||||
Shelf Life: | 12 months from delivery date in original sealed containers. | 12 months from delivery date in original sealed containers. | ||||
Pot Life: | 8 hours at 20°C | 8 hours at 20°C | ||||
Flash Point: | 25°C | 25°C |
Product Data | |||
---|---|---|---|
Dry Film Thickness | Wet Film Thickness | ||
Brush: | 50 μm | 80 μm | |
Compliant Spray Gun: | 50 μm | 80 μm | |
Pressure Pot: | 50 μm | 80 μm | |
Airless/Air-Assisted: | 50 μm | 80 μm |
Coverage: 12.5 square metres per litre @ 50 microns dft (Theoretical)
Drying Times At 20°C | |
---|---|
Touch Dry: | 2 hours |
Dry To Handle: | 24 hours |
Dry To Recoat: | After 45 minutes at 20°C without flatting. After 8 hours at 20°C either flat and recoat with itself or topcoat. |
Fully Cured: | 3 - 7 days |
Technical Data | |||||
---|---|---|---|---|---|
Brush | Compliant Spray Gun | Pressure Pot | Airless/Air-Assisted | ||
Mixing Ratio: | Base: 4 | Base: 4 | Base: 4 | Base: 4 | |
Hardener: 1 | Hardener: 1 | Hardener: 1 | Hardener: 1 | ||
Thinner: <0.5 | Thinner: 1.5 | Thinner: 1.5 | Thinner: <0.5 | ||
Hardener Options: | Hardener 9058 Standard | Hardener 9058 Standard | Hardener 9058 Standard | Hardener 9058 Standard | |
Hardener 9060 Rapid Cure | Hardener 9060 Rapid Cure | Hardener 9060 Rapid Cure | Hardener 9060 Rapid Cure | ||
Thinner Options: | Thinner 2691 | Thinner 2691 | Thinner 2691 | Thinner 2691 | |
Thinner 2711 | Thinner 2711 | Thinner 2711 | Thinner 2711 | ||
Viscosity: | - | 28 - 35 seconds B4 cup | 28 - 35 seconds B4 cup | 35 - 40 seconds B4 cup | |
Spray Gun Setup: | - | 1.8 - 2.0 | 1.1 - 1.4 | 11 - 13 thou 40/50° | |
Number Of Coats (Guide Only): | 1 - 2 full coats | 1 - 2 full coats | 1 - 2 full coats | 1 - 2 full coats | |
Flash Off: | - | 10 - 15 minutes between coats | 10 - 15 minutes between coats | 10 - 15 minutes between coats |
For further information on mixing ratios please contact Rawlins Paints on Tech - 0113 2455450 (option 2) or [email protected] Sales - 0113 2455450 or [email protected]
Information On Basic Physical And Chemical Properties | ||||||
---|---|---|---|---|---|---|
Epiprime White | Epiprime Colours | |||||
Form: | According to product specification | According to product specification | ||||
Colour: | According to product specification | According to product specification | ||||
Odour: | Characteristic | Characteristic | ||||
Odour Threshold: | Not determined | Not determined | ||||
pH-value 20°C: | Not determined | Not determined | ||||
Melting point/freezing point: | Undetermined | Undetermined | ||||
Initial boiling point and boiling range: | 36°C | 136°C | ||||
Flash Point: | 24°C | 24°C | ||||
Flammability (solid, gas): | Not applicable | Not applicable | ||||
Ignition temperature: | 500°C | 315°C | ||||
Decomposition temperature: | Not determined. | Not determined. | ||||
Auto-ignition temperature: | Product is not selfigniting. | Product is not selfigniting. | ||||
Explosive properties: | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | "Product is not explosive. However, formation of explosive air vapour mixtures are possible." | ||||
Explosion limits: Lower: | 1.1 Vol% | 1.1 Vol% | ||||
Explosion limits: Upper: | 7 Vol% | 7 Vol% | ||||
Vapour pressure at 20°C: | 6.7 - 8.2 hPa | 6.7 - 8.2 hPa | ||||
Density at 20°C: | 1.487 g/cm³ | 1.281 g/cm³ | ||||
Relative density: | Not determined | Not determined | ||||
Vapour density: | Not determined | Not determined | ||||
Evaporation rate: | Not determined | Not determined | ||||
Solubility in / Miscibility with water: | NOT MISCIBLE | NOT MISCIBLE | ||||
Partition coefficient: n-octanol/water: | Not determined | Not determined | ||||
Viscosity: Dynamic at 20°C: | 220 mPas | 300 mPas | ||||
Viscosity: Kinematic: | Not determined | Not determined | ||||
Solvent content: Organic solvents: | 28.9% | 34.3% | ||||
Solids content: | 71.1% | 65.7% |
Customer agrees that before placing an Order, Customer has read and understood the most up to date Product Data Sheet for the Product. Where we have access to the Product Data Sheet from the manufacturer, we will either provide a copy on request, or include a link to the Product Data Sheet available on the manufacturer’s website. Customer further agrees that we have no liability for any errors or omissions contained within the Product Data Sheets. For more information, please see our Terms & Conditions of Sale.
HMG Epiprime is only available with the shipping and delivery timescales listed below - please do not contact our Customer Support Team with enquiries about alternative or earlier shipping and delivery times.
Saturdays and Sundays, as well as Bank Holidays, are not classed as working days.
Orders placed after the cut-off for this product will not be processed for earliest dispatch until 9am the next working day.
All delivery costs below are excluding VAT
HMG Thinner 2691 is a thinner for use in various applications.For use with compatible HMG systems.More Information Delivery Info
£13.21 (incl. VAT)
£11.01 (ex. VAT)
HMG Thinner 2711 is a low odour thinner recommended for use in certain HMG systems.Suitable for various HMG systems.More Information Delivery Info
£47.48 (incl. VAT)
£39.57 (ex. VAT)
HMG Hardener 9060 Rapid Cure is a polyamide hardener for use as a fast option in recommended HMG systems. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG EpiprimeActivator (Part 2) HMG Hardener 9060 Rapid Cure...
£24.16 (incl. VAT)
£20.13 (ex. VAT)
HMG Hardener 9058 Standard is a polyamide hardener for use as a standard in recommended HMG systems. This product MUST be purchased/used in conjuction with its manufacturer specified base or activator/hardener:2-Pack System DetailsBase (Part 1) HMG EpiprimeActivator (Part 2) HMG Hardener 9058 StandardPart...
£7.84 (incl. VAT)
£6.53 (ex. VAT)
These surface preparation kits for steel have been created to help provide customers with an easily accessible bundle of tools to aid in the preparation of steel surfaces in accordance with ISO 8501-1 (St2/3) and SSPC (SP 2/3). Please click here for important information about these kits. Kit Contents: SET 1 (Hand Tools)1 x Rust-Oleum...
£25.84 (incl. VAT)
£21.53 (ex. VAT)